2. Home
  3. Domestic appliances
  4. Sanitary ware
  5. Aquasana
  6. AQ-SFRO-S1S3

Aquasana AQ-SFRO-S1S3 Owner's manual

  • Hello, I've reviewed the Owner's Manual for the Aquasana SmartFlow AQ-SFRO-S1S3 water filter. This manual provides instructions on how to replace the carbon block and advanced carbon block filters, as well as how to flush the system. I'm ready to answer your questions about the device, its maintenance, and the manufacturer's recommendations.
  • What is the recommended replacement frequency for the AQ-SFRO-S1S3?
    What should I do before installing new filters?
    What types of filters are in the SmartFlow AQ-SFRO-S1S3 system?
    How do I clean the system manifold and tank?
Protect your investment and save money
with our Water for Life program.
Free
Shipping
Discounted
Replacements
No
Contract
[email protected]
CONTACT US TO LEARN MORE 866-662-6885
Aquasana, Inc.
4343 S. Hamilton Road
Groveport, OH 43125
866-662-6885 USA
877-332-7873 Canada
www.aquasana.com 100368703
Certied by WQA to NSF/ANSI Standard
42, 53, 401, and CSA B483.1 when used
in the AQ-SFRO for the reduction of the
claims specied on the Performance
Data Sheet and at www.WQA.org.
For the full list of
contaminants ltered,
scan to view the
Performance Data Sheet
on Aquasana.com.
AQ-SFRO-S1S3
Under Sink Water Filter
Owner’s Manual
SmartFlow™ Reverse Osmosis Carbon Block
and Advanced Carbon Block Replacements
REPLACEMENT
The recommended replacement frequency for the AQ-SFRO-S1S3 is every 6 months or 365 gallons of use.
Use only certied, genuine Aquasana replacement lters for continued contaminant removal and
system performance.
Extended
Warranty
For use with AQ-SFRO
Turn o COLD water valve. Release pressure from system by turning on
dedicated faucet until water stops owing. Once water stops owing from
the dedicated faucet, turn the faucet o.
Unbox lter cartridge replacements and remove plastic.
Remove the Carbon Block lter cartridge from Stage 1 by turning the
handle to the left and pulling out. Discard entire lter cartridge. Repeat for
the Advanced Carbon Block (Stage 3).
1
2
3
4
5
6
7
8
NOTE: Do not drink ushed water.
Scan to view the SmartFlow™ Reverse
Osmosis lter replacement video.
INSTALLATION STEPS
Prepare for Installation
Insert each lter cartridge into its designated location in the system
manifold by turning to the right with the handle vertically aligned. The guides
on each lter will ensure proper alignment within the system manifold.
Once the lter is engaged, push the lter fully in while rotating 90 degrees
to the right. Continue this step for each lter.
• Top Filter: Carbon Block
• Bottom Filter: Advanced Carbon Block
Insert Filter Cartridges
Flush and Check for Leaks
Turn on COLD water valve and conrm
dedicated faucet is o. While tank rells,
carefully inspect for leaks.
After the water tank is full, turn on
the dedicated faucet and empty the
tank again.
Once the water tank is empty, turn o
the dedicated faucet and allow tank to rell.
Repeat this step two more times. Once you
have emptied three tanks of water, close all
faucets and rell for regular use.
NOTE: It will take 1-3 hours for the water tank
to rell.
STAGE 1
Carbon Block
STAGE 2
SmartFlow
™
Membrane
STAGE 3
Advanced Carbon Block
Care
To clean the system manifold and tank, wipe exterior with a damp cloth.
Do not use any strong or abrasive cleaning agent or solvent cleaner.
NOTICE – Safeguards: If you are experiencing a tubing connection leak,
shut o COLD water, disconnect and re-set the tube.
Do not use with water that is microbiologically unsafe or of unknown
quality without adequate disinfection before or after the system.
Conforms to NSF/ANSI 53 for VOC reduction. See performance data sheet
for individual contaminants and reduction performance.
Systems certied for cyst reduction may be used on disinfected waters
that may contain lterable cysts.
/