Alemlube SPG300-D_SPG300-R Owner's manual

Brand: Alemlube

Model: SPG300-D_SPG300-R

Type: Owner's manual

Description

The SPG300-D and SPG300-R refillable automatic grease lubricators dispense a precise amount of grease to single or multiple lube

points at pre-determined intervals. Powered by four AAA batteries, the SPG300-D can be installed directly and the SPG300-R can be

installed remotely utilising a bracket, 113cm of tubing and fittings (not depicted). The SPG300-D and SPG300-R refillable automatic

grease lubricators can be set to dispense 300cc of grease within a 1 month period or periods of 3, 6 or 12 months. Quick and easy

refilling can be achieved with the aid of a suitable bulk grease source (20kg grease kit) or a portable grease gun.

Specifications

Installation

Direct Install (SPG300-D)

1 Remove the grease nipple from the bearing and attach the automatic grease

lubricator directly using an 11mm spanner

2 Switch on by turning the battery cap clockwise until it locks

3 The green light should come on for a few seconds after initial start up

Remote Install (SPG300-R)

1 Attach the bracket supplied to the automatic grease lubricator using a 12mm spanner

2 Connect the automatic grease lubricator to the specified bearing grease nipple

utilising the supplied 113cm long tubing (maximum remote mount capabilities of 2

metres using your own tubing)

3 Fix the automatic grease lubricator with attached mounting bracket in the desired

position with the hardware supplied

4 Switch on by turning the battery cap clockwise until it locks

5 The green light should come on for a few seconds after initial start up

Operation Status

1 When powering the SPG up by doing up the battery cap, the green light comes on for

about 1 second to show the unit is working

2 It will complete 1 lube cycle at this time – around 10 seconds long

3 If the red light starts flashing at this time, for about 10 seconds, the batteries are

weak and should be replaced or that the back pressure is excessive and the unit is

struggling to pump – change the batteries and if the red flashing on start up

continues, check the bearing/feed line.

Changing the Batteries

1 Unscrew the yellow cap at the top of

the automatic grease lubricator and

insert the batteries as shown

Changing the Discharge Interval

1 Unscrew the yellow cap and remove the four AAA batteries

2 Using a 2.5mm Allen key, remove the top section to access

the mode setting device

Uses Automatic lubrication of single or multiple lube points

Power Supply 4 x 1.5V (AAA batteries)

Motor Power Minimum 3.02V DC / maximum 6V DC

Discharge Quantity 0.085cc per stroke

Discharge Intervals 300cc of EP#1 or EP#2 grease within a 1 month, 3 month, 6 month or 12 month period

Operating Temperature -10ºC to +50ºC

BATTERY ORIENTATION

= NEGATIVE DOWN

POSITIVE DOWN

12 3

12 months setting shown

Visit our website at www.alemlube.com.au Email - inf[email protected]

Refillable Automatic Grease Lubricator

SPG300-D

SPG300-R

NSW

TEL: (02) 9939 0711

FAX: (02) 9939 0411

QLD/PNG

TEL: (07) 3889 8480

FAX: (07) 3889 8490

VIC/TAS

TEL: (03) 8787 8288

FAX: (03) 8787 8266

TEL: (08) 9209 3066

FAX: (08) 9209 3933

SA/NT

TEL: (08) 8241 7111

FAX: (08) 8241 7011

TEL: (09) 447 1007

FAX: (09) 447 1008

OWNER’S MANUAL

Alemlube SPG300-D_SPG300-R Owner's manual

Alemlube SPG300-D_SPG300-R Owner's manual

Alemlube SPG300-D_SPG300-R Owner's manual

Related papers

Other documents