www.lorextechnology.com
LW2960_SERIES_QSG_EN_R1 Page 1
B. LCD Receiver Setup
1
Insert the included microSD card into the microSD card slot on
the LCD receiver until you hear a “click.”
NOTE: The receiver is compatible with most major brands of
microSD card up to 64 GB.
2
Pull out the receiver stand for convenient
placement on a flat surface.
Connect one end of the receiver’s power adapter to the back
of the receiver. Connect the other end to an electrical outlet.
NOTE: Make sure to first connect the
camera(s) to an electrical outlet before
powering on the receiver. This will
ensure a proper connection.
3
4Pull up the antennas on the back of the LCD receiver.
5Push the power button on top of the LCD receiver.
NOTE: If one or more cameras do not appear when selected (i.e., Camera 2 is
plugged in but does not appear on channel 2), follow the pairing process
described in the user’s guide.
*Number of cameras, and microSD card capacity may vary
by model. Check your package for specific content information.
Time
Under 20
minutes*
NOTE: AVOID INSTALLING IN A LOCATION
THAT REQUIRES THE WIRELESS SIGNAL TO
PASS THROUGH CEMENT, CONCRETE, OR
METAL STRUCTURES. THIS WILL REDUCE THE
TRANSMISSION RANGE.
WIRELESS VIDEO MONITORING SYSTEM
LW2960 SERIES
QUICK START GUIDE
Charge the receiver for at least 6 hours before using.
The receiver has a rechargeable battery for up to 3.5 hours of portable use.
This system comes with the following
components:
• 9” wireless LCD video monitor
• Indoor / outdoor color camera(s)*
• SD memory card*
• Mounting hardware kit(s)*
• Power adapters*
• Ethernet cable
Loosen the thumbscrews (1, 2) and the adjustment ring (3) by turning
them counter clockwise.
2
1Use the included mounting screws to attach the camera(s) to the
mounting surface:
a. Mark the positions of the screw holes on the mounting surface.
b. Drill holes and insert the drywall anchors (included) as needed.
c. Firmly attach camera(s) to the surface using the included screws.
2
1
3
Adjust the angle of the camera(s) as needed, then tighten the
thumbscrews and the adjustment ring.
A. Camera Setup
Before installing camera(s), carefully plan where and how it will be positioned,
and where you will route the cable that connects the camera to the power adapter.
3Connect one end of the camera’s power adapter to the camera and the
other end to an electrical outlet. Make sure the power connector is fully
inserted to avoid water getting in the plug.
4Remove the protective film from the front of the camera(s). If the film is
not removed, it will block the microphone and will affect picture quality.
• Cameras are rated for indoor/outdoor installation, but are not intended for direct
exposure to rain or snow. For outdoor applications install under shelter protected
from the elements.
• Wireless cameras require a power source to operate.
• Ensure power outlets are sheltered from the elements.
Installation Tips
NOTE: If you run the power cable through the mounting surface,
connect power before attaching the camera to the wall.
*
www.lorextechnology.com
LW2960_SERIES_QSG_EN_R1 Page 2
©2014 Lorex Technology Inc.
As our product is subject to continuous improvement, Lorex Technology &
subsidiaries reserve the right to modify product design, specifications, prices &
warranty without notice and without incurring any obligation. E&OE
Front Panel Buttons:
Menu: Open main menu. Return to previous menu / exit menus without
saving changes.
Quad / Sequence Viewing: Switch between Quad mode (up to 4
channels) and Auto Sequence mode (automatically cycles through channels).
Scan Mode: Enter Scan mode (display turns on only when motion is
detected).
Channel Select: Change channel.
Zoom: Activate / deactivate 2x digital zoom. Use the joystick to adjust the
viewing area (must be in single-channel view).
Delete File: Delete the highlighted file in Playback mode.
Joystick: Scroll up / down / left / right in menus. Push to make a
selection in menus, or enter Playback mode from live view.
Side Panel Buttons:
Motion Recording: Activate / deactivate motion recording.
Manual Recording: Activate / deactivate manual recording.
Talk: Press and hold to activate intercom (two-way audio).
C. Basic System Setup
WIRELESS VIDEO MONITORING SYSTEM
LW2960 SERIES
QUICK START GUIDE
Scan the QR code or go to the
address below for the complete
user’s guide.
lorex.ca/SDPro9
1. Press to open the main menu. Move the joystick
left / right to highlight Settings and push the joystick to
select.
2. Select Date & Time and push the joystick to confirm.
3. Move the joystick left / right to move the cursor. Move the joystick
up / down to change the year, month, day, hour, minutes, seconds.
NOTE: The system uses a 24-hour clock.
4. Push the joystick to save your settings.
5. Press to close any remaining menu
windows.
NOTE: See the user’s guide for details on
configuring Daylight Savings Time and
Network Time Protocol.
D. Setting the Date & Time NOTE: It is important to set the date and time to ensure that they are properly captured on recordings.
1Connect the included Ethernet cable from the Ethernet port on the
LCD receiver to your wireless router. The network icon turns green.
2Download the free Lorex SD Pro app from the App Store. Once installed,
tap to launch the app.
Tap QRCode to scan the QR
code on the back of the receiver.
OR
Tap Add to enter the UID manually.
iPhone® / iPad®Android™
4
5Enter the following:
Enter the password (default: 000000).
Enter a personalized name for the system.
Enter the UID printed below the QR code on the back
of the receiver. If you tapped QRCode in Step 4, this
field populates automatically.
6Tap Save. The system will show in your device list with an Online status.
7Tap the name of the system. You will be asked to enter a new, secure password.
Congratulations! You are now connected to your surveillance system over the Internet.
View live video from your camera(s) in portrait or landscape mode.
3Tap Click here to add device.
4Enter the following:
Enter the password (default: 000000).
Enter a personalized name for the system.
Tap Scan to scan the QR code on the
back of the receiver.
OR
Enter the UID printed below the QR code.
7Tap OK. The system will show in your device list with an Online status.
8Tap the name of the system. You will be asked to enter a new, secure password.
5Tap OK. The system will show in your device list with an Online status.
6
E. Smartphone / Tablet Setup
3Tap Add Device.
1Connect the included Ethernet cable from the Ethernet port on the
LCD receiver to your wireless router. The network icon turns green.
2Download the free Lorex SD Pro app from the Google Play Store. Once
installed, tap to launch the app.
NOTE: You may need to turn the receiver off and on again. NOTE: You may need to turn the receiver off and on again.
Write your password down for future reference: __________________________________________
It’s all on the Web
NOTE: Be sure to leave the receiver connected to a power outlet to ensure remote connectivity.
/
