Lorex LW2760 Series Quick start guide

Category
Dashcam
Type
Quick start guide
LW2760_SERIES_QSG_EN_R1
www.lorextechnology.com
Time
Under 20 minutes*
NOTE: AVOID INSTALLING IN A LOCATION THAT
REQUIRES THE WIRELESS SIGNAL TO PASS THROUGH
CEMENT, CONCRETE, OR METAL STRUCTURES. THIS
WILL REDUCE THE TRANSMISSION RANGE.
Loosen the thumbscrews (1, 2) and the adjustment ring (3) by turning them
counter clockwise.
2
1
Use the included mounting screws to attach the camera(s) to the mounting surface:
a. Mark the positions of the screw holes on the mounting surface.
b. Drill holes and insert the drywall anchors (included) as needed.
c. Firmly attach camera(s) to the surface using the included screws.
3
Adjust the angle of the camera(s) as needed, then tighten the thumbscrews and
the adjustment ring.
A. Camera Setup
Before installing camera (s), carefully plan where and how it will be positioned,
and where you will route the cable that connects the camera to the power adapter.
3
Connect one end of the camera’s power adapter to the camera and the other end to
an electrical outlet. Make sure the power connector is fully inserted to avoid water
getting in the plug.
4
Remove the protective film from the front of the camera(s). If the film is not
removed, it will block the microphone and will affect picture quality.
This system comes with the following
components:
7” wireless LCD video monitor
Indoor / outdoor color camera (s)*
SD memory card*
Mounting hardware kit(s)*
Power adapters*
Ethernet cable
*Camera configuration, memory card size, and the number of accessories may vary by
model. Please refer to your package for specific details.
Cameras are rated for indoor/outdoor installation, but are not intended for direct exposure to rain
or snow. For outdoor applications, install under shelter protected from the elements.
Wireless cameras require a power source to operate.
Ensure power outlets are sheltered from the elements.
Installation Tips
NOTE: If you run the power cable through the mounting surface, connect power
before attaching the camera to the wall.
*
WIRELESS VIDEO MONITORING SYSTEM
LW2760 SERIES
QUICK START GUIDE
3
5
6
1
B. LCD Receiver Setup
Insert the included SD card into the SD card slot on the LCD receiver until you hear a “click.”
Connect one end of the receiver’s power adapter to the side of the receiver. Connect the other
end to an electrical outlet.
Pull up the antenna on the back of the LCD receiver.
Slide the power switch on the side panel of the LCD receiver to the “ON” position.
NOTE: If one or more cameras do not appear when selected (i.e., Camera 2 is plugged in but does not
appear on channel 2), follow the pairing process described in the user’s guide.
NOTE: Make sure to first connect the camera(s) to an electrical outlet before powering on
the receiver. This will ensure a proper connection.
2
1
© 2016 Lorex Corporation
As our product is subject to continuous improvement, Lorex Corporation & subsidiaries reserve the right to
modify product design, specifications & prices without notice and without incurring any obligation. E&OE.
NOTE: The receiver is compatible with most major brands of SD card up to 64 GB.
LW2760_SERIES_QSG_EN_R1
www.lorextechnology.com
Front Panel Buttons:
Motion Recording: Activate / deactivate motion recording.
Menu: Open main menu. Return to previous menu / exit menus without
saving changes.
Quad / Sequence Viewing: Switch between Quad mode (up to 4 channels) and Auto
Sequence mode (automatically cycles through channels).
Scan Mode: Enter Scan mode (display turns on only when motion is detected).
Channel Select: Change channel.
Zoom: Activate / deactivate 2x digital zoom. Use the joystick to adjust the viewing area
(must be in single-channel view).
Delete File: Delete the highlighted file in Playback mode.
Joystick: Scroll up / down / left / right in menus. Push to make a
selection in menus, or enter Playback mode from live view.
Top Panel Buttons:
Volume Down
Volume Up
Talk: Press and hold to activate intercom (two-way audio).
Manual Recording: Activate / deactivate manual recording.
C. Basic System Setup
1. Press to open the main menu. Move the joystick
left / right to highlight Settings and push the joystick to select.
2. Select Date & Time and push the joystick to confirm.
3. Move the joystick left / right to move the cursor. Move the joystick up / down to
change the year, month, day, hour, minutes, and seconds.
NOTE: The system uses a 24-hour clock.
4. Push the joystick to save your settings.
5. Press to close any remaining menu windows.
NOTE: See the user’s guide for details on configuring
Daylight Savings Time and Network Time Protocol.
D. Setting the Date & Time
NOTE: It is important to set the date and time to ensure that they are properly captured on recordings.
1
Connect the included Ethernet cable from the Ethernet port on the
LCD receiver to your wireless router. The network icon turns green.
2
Download the free Lorex SD Pro app from the App Store. Once installed, tap to launch
the app.
Tap QRCode to scan the QR
code on the back of the receiver.
OR
Tap Add to enter the UID manually.
iPhone® / iPad® Android™
4
5
Enter the following:
Enter the password (default: 000000).
Enter a personalized name for the system.
Enter the UID printed below the QR code on the back of the
receiver. If you tapped QRCode in Step 4, this field populates
automatically.
6
Tap Save. The system will show in your device list with an Online status.
7
Tap the name of the system. You will be asked to enter a new, secure password.
Congratulations! You are now connected to your surveillance system over the Internet.
View live video from your camera(s) in portrait or landscape mode.
3
Tap Click here to add device.
4
Enter the following:
Enter the password (default: 000000).
Enter a personalized name for the system.
Enter the UID printed below the QR code.
OR
7
Tap OK. The system will show in your device list with an Online status.
8
Tap the name of the system. You will be asked to enter a new, secure password.
5
6
E. Smartphone / Tablet Setup
3
Tap Add Device.
1
Connect the included Ethernet cable from the Ethernet port on the
LCD receiver to your wireless router. The network icon turns green.
2
Download the free Lorex SD Pro app from the Google Play Store. Once installed, tap to
launch the app.
NOTE: You may need to turn the receiver off and on again.
NOTE: You may need to turn the receiver off and on again.
Write your password down for future reference: __________________________________________
NOTE: Be sure to leave the receiver connected to a power outlet to ensure remote connectivity.
WIRELESS VIDEO MONITORING SYSTEM
LW2760 SERIES
QUICK START GUIDE
Need Help?
Visit us online for up-to-date software and complete instruction manuals
Tap Scan to scan the QR code on the back of the receiver.
© 2016 Lorex Corporation
As our product is subject to continuous improvement, Lorex Corporation & subsidiaries reserve the right to
modify product design, specifications & prices without notice and without incurring any obligation. E&OE.
1
3
Go to www.lorextechnology.com
Search the model number of your product
Click on your product in the search results
Click the Downloads tab
2
4
  • Page 1 1
  • Page 2 2

Lorex LW2760 Series Quick start guide

Category
Dashcam
Type
Quick start guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI