Campbell Scientific SkyVUE8M Owner's manual

Revision:08/2020

Campbell Scientific, Inc.

Table of contents

1. General information 1

1.1 Packing list 1

1.2 General safety 1

1.3 Sensor unit safety 2

1.4 Laser safety 2

1.5 Electrical safety 4

2. Product overview 5

2.1 Introduction 6

2.1.1 Cloud height detection 6

2.1.2 Sky condition 7

2.1.3 Backscatter profile reporting 7

2.2 Optical measurement 8

2.2.1 Optical arrangement 8

2.3 Internal monitoring 8

2.4 Specifications 9

2.4.1 Measurement specifications 9

2.4.2 Mechanical specifications 9

2.4.3 Electrical specifications 10

2.4.4 Optical specifications 12

2.4.5 Environmental specifications 12

2.4.6 Communications specifications 12

2.4.7 Transport, shock, and vibration certification 13

2.4.8 Compliance and testing 13

3. Initial preparation and checks 14

4. Installation 15

4.1 Location and orientation 15

4.2 Grounding 15

4.3 Mounting the SkyVUE 8M 16

4.4 Tilt angle 17

4.5 Connectors and wiring 17

4.5.1 Base connectors 18

Table of Contents - i

4.5.2 Wiring using supplied Campbell Scientific cables 19

4.5.2.1 Power connections 20

4.5.2.2 Communications connections 20

4.5.3 USB connection 21

4.5.4 I/O connection 21

4.6 Military transport case 22

4.7 Bird spike kit 22

4.8 Storage information 24

4.9 Fitting the camouflage cover 24

5. Operation 24

5.1 Terminal mode 24

5.1.1 Entering/exiting the SkyVUE 8M terminal mode 25

5.1.2 Terminal mode commands general 25

5.1.3 Terminal mode command examples 26

5.1.4 Application command message types 41

5.1.5 MCFG command message types 42

5.1.6 Measurement and message intervals 43

5.1.7 Status command 46

5.1.8 Message polling 55

5.1.9 Loading a new operating system (OS) 56

5.1.10 Stratocumulus backscatter calibration 57

5.1.11 CRC-16 codes on terminal commands 59

5.1.12 Service command 59

5.1.13 Locked features 60

5.2 Restoring factory defaults 61

5.3 LED indicator 62

6. Messages 62

6.1 Data messages general 63

6.2 Checksums used in SkyVUE 8M messages 63

6.3 CS messages 64

6.3.1 MESSAGE 001 (no profile, no sky condition) 64

6.3.2 MESSAGE 002 (Profile, no sky condition) 68

6.3.3 MESSAGE 003 (no profile, sky condition) 71

6.3.4 MESSAGE 004 (profile, sky condition) — default message 73

6.4 CL31 messages 77

Table of Contents - ii

6.4.1 MESSAGES 101 - 106, (CL31 MESSAGE 1) 77

6.4.2 MESSAGE 005 (no profile, sky condition, mixing layer heights) 78

6.4.3 MESSAGES 107 - 112, CL31 Message 2 82

6.5 CT25K messages 86

6.5.1 MESSAGE 113, CT25K Data Message No. 1 86

6.5.2 MESSAGE 114, CT25K Data Message No. 6 89

7. Maintenance 91

7.1 General 91

7.2 Cleaning 91

7.3 Diagnostic LED indicators within the enclosure 92

Appendix A. Measurement of the attenuated backscatter profile 94

A.1 Initial measurement 94

A.2 Backscatter onset height detection 94

A.3 Produce attenuated backscatter output message 95

Appendix B. Cloud height calculation 96

Appendix C. Sky condition algorithm description 97

Appendix D. Replacing the SkyVUE 8M PSU 99

Appendix E. SkyVUE 8M Laser/APD module replacement 101

List of figures

FIGURE 1-1. Location of laser warning label 4

FIGURE 2-1. Principle of operation 8

FIGURE 2-2. SkyVUE 8M dimensions 10

FIGURE 2-3. PSU types 11

FIGURE 4-1. Military base 17

FIGURE 4-2. Connector layout 18

FIGURE 4-3. Cable connections 21

FIGURE 4-4. USB port 21

FIGURE 4-5. Ceilometer bird spike kit installed 22

FIGURE 4-6. Preparing the SkyVUE 8M for installing the bird spikes 23

FIGURE 4-7. Attaching bird spikes to the SkyVUE 8M cowl 23

FIGURE 5-1. Restoring factory defaults 61

FIGURE 5-2. LED indicator 62

FIGURE 7-1. Diagnostic LED indicators 93

Table of Contents - iii

List of tables

Table 1-1: Packing list 1

Table 4-1: Power and communications connectors 18

Table 4-2: Function of the connector pins for the blower/heater connector 19

Table 5-1: Summary of the terminal mode commands available 27

Table 5-2: Summary of applications and applied settings for SkyVUE 8M 42

Table 5-3: Summary of message ID and descriptions 43

Table 6-1: Most significant alarm word for CS messages 65

Table 6-2: Middle alarm word for CS messages 66

Table 6-3: Least significant alarm word for CS messages 67

Table 6-4: Most significant alarm word for CS31 messages 79

Table 6-5: Middle alarm word for CS31 messages 80

Table 6-6: Least significant alarm word for CS31 messages 80

Table 6-7: Most significant alarm word for CT25K messages 87

Table 6-8: Second alarm word for CT25K messages 88

Table of Contents - iv

1. General information

1.1 Packing list 1

1.2 General safety 1

1.3 Sensor unit safety 2

1.4 Laser safety 2

1.5 Electrical safety 4

1.1 Packing list

The following table lists the products shipped with the SkyVUE 8M.

Table 1-1: Packing list

Description Quantity

Ceilometer 1

Cable, USB type A plug to type B plug, 2 m 1

Triangle key 1

Calibration plate 1

Canvas cover, white 1

Canvas cover, olive green 1

T-shaped heavy duty stakes 5

Power and communications cable 1

1.2 General safety

This manual provides important safety considerations for the installation, operation and

maintenance of the SkyVUE™8M. These safety considerations are classified into three levels:

WARNING:

Warnings alert the installer or user to serious hazards. Ignoring these warnings could result in

injury or death and/or irrevocable damage to the sensor unit.

SkyVUE™8M Tactical LIDAR Ceilometer 1

CAUTION:

Cautions warn of potential hazards. Ignoring these cautions could result in the sensor being

damaged and data being lost.

NOTE:

Notes highlight useful information in the installation, use and maintenance of this product.

These should be followed carefully in order to gain the maximum benefit from the use of this

product.

1.3 Sensor unit safety

The SkyVUE 8M sensor has been checked for safety before leaving the factory and contains no

parts that need to be changed during normal use.

WARNING:

Do not modify the SkyVUE 8M unit. Such modifications will lead to damage of the unit and

could expose users to dangerous light levels and voltages.

WARNING:

Do not attempt to repair the SkyVUE 8M unit without consulting Campbell Scientific.

CAUTION:

Ensure that the correct voltage supply is provided to the sensor.

1.4 Laser safety

The SkyVUE 8M sensor incorporates an InGaAs laser diode which is rated as a class 3B device.

This is an embedded laser where the output from the sensor unit, through the optics, is

minimized to class 1M. This classification indicates that viewing of the beam with the naked eye is

safe but looking directly into the beam with optical instruments, e.g. binoculars can be

dangerous.

From the laser head the output has the following characteristics:

Maximum average power: 15.0 mW (through 50 mm)

Maximum pulse energy: 1500 nJ (through 50 mm)

Pulse duration: 100 ns

Pulse frequency: 10 kHz

Wavelength: 912 nm ± 5 nm

SkyVUE™8M Tactical LIDAR Ceilometer 2

Tested to: EN 60825-1:2014

Half angle divergence: 0.44 mrad

The sensor is marked with the following warning information:

INVISIBLE LASER RADIATION

DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS

CLASS 1M LASER PRODUCT

WARNING:

Removing the laser module with the power applied to the SkyVUE 8M may expose the user to

hazardous class 3B laser radiation.

No attempt should be made to operate the laser module outside of the housing.

WARNING:

Annually, check that the laser warning label on the sensor is still visible and can be clearly

read.

When installing the sensor, avoid pointing the laser housing towards areas where binoculars

are in common use.

WARNING:

Use of controls or adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

SkyVUE™8M Tactical LIDAR Ceilometer 3

FIGURE 1-1. Location of laser warning label

Before removing the laser module, the sensor must be physically disconnected from its power

supply to ensure that the laser is turned off.

1.5 Electrical safety

The sensor is powered from a low voltage supply (Electrical specifications (p. 10)), but potentially

hazardous voltages are generated within the internal electronics. Wiring of the power and data

cable should only be done by personnel qualified to install electrical equipment. For outside

installations, this usually requires a certified electrician who is familiar with local electrical and

safety legislation. Some general guidance is given in Connectors and wiring (p. 17), but the

responsibility for the installation lies with the installer.

The unit is tested for electrical safety before dispatch but may need subsequent testing according

to local practice.

SkyVUE™8M Tactical LIDAR Ceilometer 4

NOTE:

The unit should only be serviced by trained personnel.

WARNING:

Removal of electronic module covers or connectors while the unit is powered will expose the

operator to potentially hazardous voltages and risk damage to the sensor.

The SkyVUE 8M has electrical and laser warning labels on the exterior and interior of the unit.

It is recommended that the hood and access panel door are not opened in conditions of rain,

hail or snow.

Isolate the sensor before removing internal components, including the cover to the avalanche

photodiode (APD) module. Only trained personnel should disassemble the instrument.

Power connectors are shrouded to prevent touching of the contacts. The power supply should be

isolated when connecting and disconnecting the cables to the sensor.

The SkyVUE 8M must be properly grounded by a licensed and qualified electrician to protect

against voltage leakage shock risk (Grounding (p. 15)).

Campbell Scientific recommends that RCD protection units be used with all sensors. See Power

connections (p. 20) for further information.

Heaters are enclosed to prevent contact.

CAUTION:

When powered, the heaters may operate automatically and without warning. They may

remain hot when not powered. Follow the isolation precautions, to avoid shock and burn

hazards.

2. Product overview

2.1 Introduction 6

2.2 Optical measurement 8

2.3 Internal monitoring 8

2.4 Specifications 9

SkyVUE™8M Tactical LIDAR Ceilometer 5

2.1 Introduction

The SkyVUE 8M is a LIDAR (LIght Detection And Ranging) that emits short pulses of near infrared

light into the atmosphere from a semiconductor laser. The pulses of infrared light are scattered

back by aerosols including cloud droplets. The time between transmission of the pulse and the

return signal gives the range, and therefore height, of the scattering aerosols. The variation in the

strength of the back-scattered light signal with height gives a profile of scatter coefficients and

allows identification of cloud bases. If significant scattering is detected without a defined cloud

base, then a vertical visibility can be calculated.

The control system of the SkyVUE 8M is divided into three modules, DSP, TOP and PSU as

follows:

DSP (Digital Signal Processor) is the main data processing and communications unit of the

SkyVUE 8M. It hosts two separate time keeping circuits that are cross checked. An alarm is

triggered if the circuits disagree.

TOP (top of the unit) provides safety shutdown features such as over and under laser output

level. It also contains the calibration circuitry and dirty windows system.

PSU (Power Supply Unit) controls the power supply including battery charging and deep

discharge protection.

The SkyVUE 8M has a rugged environmental enclosure that protects the instrument from the

harshest conditions and will measure the atmosphere with high stability and repeatability.

2.1.1 Cloud height detection

A scatter profile is measured as described in Measurement of the attenuated backscatter profile

(p. 94).

Cloud height detection is carried out as described in Cloud height calculation (p. 96). Up to four

cloud heights can be detected.

If clouds are not detected, the SkyVUE 8M will give one of these reports:

l No significant backscatter.

l Full obscuration determined but no cloud base detected. This is reported if the criteria for

detecting cloud base is not met but the integrated scattering coefficient reaches the limit

of vertical visibility below a set height limit. The default value is 2000m (6560ft) but can be

changed by the user. The height at which this occurs is given as vertical visibility.

SkyVUE™8M Tactical LIDAR Ceilometer 6

l Some obscuration detected but determined to be transparent is reported if scattering is

detected but no cloud is detected and the calculated vertical visibility exceeds a set height

limit.

If no cloud is detected but significant scattering is detected below 50m (160ft), then vertical

visibility is set to 0.

2.1.2 Sky condition

Sky condition is an assessment of cloud cover measured in units of eighths known as oktas. The

number of oktas is the density of cloud in eighths of that layer. The SkyVUE 8M can report up to

five layers of cloud when reporting sky condition. The algorithm used in the SkyVUE 8M follows

guidance in the ICAO 9837, Manual on Automatic Meteorological Observing Systems at

Aerodromes.

Sky condition is not an instantaneous measurement. It is based on cloud data for the previous 30

minutes, with cloud detection in the previous 10 minutes given an extra weighting. Therefore, sky

condition is not available until sufficient data has been collected. See Sky condition algorithm

description (p. 97) for more detail.

2.1.3 Backscatter profile reporting

Several possible data messages give the two-way attenuated backscatter profile. This consists of

2048 groups of five-character values (10,240 characters in total). Each character is 4 bits long and

therefore each 5 figure group is 20 bits. They are given as signed two complement integers and

numbers greater than 2

19

–1 represent negative integers.

NOTE:

After 1600, the remaining groups have values of 00000 to maintain compatibility of the

backscatter profile reporting with other sensor models.

Therefore, each group actually represents negative, a value between –2

19

to +(2

19

–1), rather than

0 to (2

20

–1), which would be the case for unsigned, positive, 20-bit integers.

Apply the following two-stage process to correct the decimal value:

1. Convert the hexidecimal characters to a decimal number.

2. If the number resulting from this conversion is greater than 524287, subtract 1048576,

which is 2

20

.

To use this backscatter coefficient in units of sr

-1

m

-1

, the sensor multiplies the calculated decimal

number by a factor of 10

-8

. The values are scaled by the Attenuated_SCALE parameter, see

Table 5-1 (p. 27).

SkyVUE™8M Tactical LIDAR Ceilometer 7

NOTE:

The profile is not corrected for tilt angle even if cloud heights are corrected.

2.2 Optical measurement

FIGURE 2-1. Principle of operation

2.2.1 Optical arrangement

The SkyVUE 8M uses a single lens design that increases optical signal-to-noise ratio, while

maintaining Class 1M eye safety by integrating larger optics into a compact package (see FIGURE

2-1 (p. 8)). Half of the lens is used by the transmitter, and the other half is used by the receiver.

This design provides an alternative to traditional two lens or common-optics designs. The optical

isolation of traditional biaxial systems is maintained to increase detector sensitivity, while the low

overlap onset height of common-optics systems is incorporated to allow measurements at close

ranges.

2.3 Internal monitoring

The SkyVUE 8M monitors window contamination, key voltages and currents, internal

temperature and relative humidity, and other parameters relevant to its performance. Data

SkyVUE™8M Tactical LIDAR Ceilometer 8

messages (see Operation (p. 24)) include this information allowing remote diagnosis of the

SkyVUE 8M condition. In addition, a special status message can be polled.

2.4 Specifications

2.4.1 Measurement specifications 9

2.4.2 Mechanical specifications 9

2.4.3 Electrical specifications 10

2.4.4 Optical specifications 12

2.4.5 Environmental specifications 12

2.4.6 Communications specifications 12

2.4.7 Transport, shock, and vibration certification 13

2.4.8 Compliance and testing 13

2.4.1 Measurement specifications

Maximum reporting range: 8 km (26,250 ft)

Minimum reporting resolution:

5 m (15 ft)

Hard target range accuracy:

± 0.25% ± 4.6 m (15 ft)

Reporting cycle:

2 to 600 s

Cloud layers reported:

Up to four layers reported

, instantaneously. Up to five layers

reported in Sky Condition.

2.4.2 Mechanical specifications

Height: 763 mm (30 in) including feet

Width: 253 mm (10 in); 508 mm (20 in) with extended feet

Depth: 360 mm (14.2 in); 435 mm (17 in) with extended feet

Ceilometer weight: 18 kg (40 lb)

, excluding cables

Shipping weight: 24.6 kg (54 lb)

Hard shell transport case

Dimensions:

1000 mm x 600 mm x 600 mm (39.5 x 24 x 24 in)

SkyVUE™8M Tactical LIDAR Ceilometer 9

Weight (empty):

28 kg (62 lb)

Weight with ceilometer and

accessories:

49 kg (108 lb)

FIGURE 2-2. SkyVUE 8M dimensions

2.4.3 Electrical specifications

Power required: 10 to 40 VDC (9 A at 12 VDC; 4.5 A at 24 VDC), 102

W total

maximum

DSP and internal heaters:

10 to 40 VDC input;

3.8

A at 12 VDC;

1.9

A at 24 VDC

12V OUT:

1.7 A for optional or external equipment (if the SkyVUE 8M is

using a DC supply

of less than 14 VDC

,

the 12V OUT will be

less than 12 VDC

.)

Dew heater: 10 W maximum

Hood heater input:

5 A at 12 VDC; 2.5 A at 24 VDC

Fuses:

DSP fuse:

HBC 5A (T)

SkyVUE™8M Tactical LIDAR Ceilometer 10

PSU fuse:

HBC

5A

(T)

All fuses are 5 x 20 mm slow blow (T) and are the same for

both 115VAC and 230VAC.

The heaters are resistive, which is advantageous when connected to generators or when current

consumption is important.

WARNING:

Removing the laser module with a battery connected or power applied to the SkyVUE 8M

may expose the user to hazardous Class 3B radiation. No attempt should be made to operate

the laser module outside of the housing.

FIGURE 2-3. PSU types

SkyVUE™8M Tactical LIDAR Ceilometer 11

2.4.4 Optical specifications

Pulse duration:

100 ns

Pulse frequency:

10 kHz

Wavelength:

912 ± 5 nm

Half-angle laser divergence: 0.44

mrad

Field of view: 2.0

mrad

Laser lifetime:

10 years typical

Eye safety class:

1M

2.4.5 Environmental specifications

Standard operating

temperature range:

–40 to 60 °C

Relative humidity range:

0 to 100%

IP rating:

IP 66

Maximum tested wind speed:

55 m/s

for sensor securely attached to the ground without

camouflage covers

2.4.6 Communications specifications

Supported serial settings:

8 bits, no parity, 1 stop bit (default)

7 bits, even parity, 1 stop bit

7 bits, odd parity, 1 stop bit

Supported data rates: 300 baud 19200 baud

600 baud 38400 baud

1200 baud 57600 baud

2400 baud 76800 baud

4800 baud 115200 baud (default)

9600 baud

Supported standards:

RS-232 (default)

RS-485 full duplex

RS-485 half duplex

SkyVUE™8M Tactical LIDAR Ceilometer 12

Signal voltage levels:

Minimum value Nominal value Maximum value

RS-232 communications

RS-232 input threshold low 0.8 V 1.5 V –

RS-232 input threshold high – 2.0 V 2.4 V

RS-232 input absolute maximum –15 V – +15 V

RS-232 input resistance 12 KΩ – –

RS-232 output voltage low – – 0.4 V

RS-232 output voltage high (into 3 KΩ) 4.4 V – –

RS-485/422 communications

RS-485/422 input threshold voltage –0.2 V – +0.2 V

RS-485/422 output (unloaded) – – 5V

RS-485/422 output (load 50 Ω) 2 V – –

Maximum voltage at any terminal –7 V – +7 V

USB Service Port USB1.1 and 2.0 compatible, fixed 115200 baud.

2.4.7 Transport, shock, and vibration certification

When contained within the military transport case from Campbell Scientific (see Military

transport case (p. 22)), the SkyVUE 8M complies with the following standards:

MIL-STD-810g

DEF STAN 00-035

Further details are available from Campbell Scientific.

2.4.8 Compliance and testing

NOTE:

Further details regarding compliance and testing are available upon request.

EMC compliance:

EN 61326-1:2013

Electrical safety compliance:

EN 61010-1:2010

SkyVUE™8M Tactical LIDAR Ceilometer 13

Laser safety compliance:

EN 60825-1:2014

Eye safety standard:

Class 1M

Vibration:

BS EN 60068-2-6:2008 Test Fc: Vibration (Sinusoidal)

Frequency range:

5 to 150 Hz (exceeds Lloyd's Register test levels)

3. Initial preparation and checks

The following steps will provide basic familiarization with the SkyVUE 8M and perform basic

functionality checks. To do these, and connect the sensor to its power supply.

WARNING:

The laser begins operating as soon as the power is connected. Do not point the laser in any

direction where it could be viewed with magnifying optics.

The green LED visible from above should flash once every 10 seconds (see FIGURE 5-2 (p. 62)).

Connect the SkyVUE 8M USB port (see FIGURE 4-4 (p. 21)) to a computer and use a terminal

emulation program to set to 115200 baud, 8N1 bits/parity settings.

The computer should identify the USB connection and allocate a port number. Enter the port

setting in the terminal emulator program. Older computer operating systems may need

upgrading or additional software.

The SkyVUE 8M will output message type 004 (default) every 30 seconds (see CS messages (p.

64)).

Use the open 0 command to open the terminal mode. You should now see the prompt CS136>.

Type Status to see the sensor status information described in Status command (p. 46). If using

date/time information, checked it since the date/time can drift up to ±14 seconds per day.

If the unit has been in storage or transit for more than a few months, the clock battery may be

discharged. However, it will charge once power is supplied.

Use the Close command to exit the terminal mode. It will close automatically after 10 minutes of

inactivity.

SkyVUE™8M Tactical LIDAR Ceilometer 14

4. Installation

4.1 Location and orientation 15

4.2 Grounding 15

4.3 Mounting the SkyVUE 8M 16

4.4 Tilt angle 17

4.5 Connectors and wiring 17

4.6 Military transport case 22

4.7 Bird spike kit 22

4.8 Storage information 24

4.9 Fitting the camouflage cover 24

4.1 Location and orientation

The SkyVUE 8M measures environmental variables and is designed to be located in harsh

weather conditions. However, there are a few considerations to take into account if accurate and

representative data from a site are to be obtained.

To reduce the service frequency with the unit, place the SkyVUE 8M away from sources of

contamination. More regular maintenance will be required when the instrument is placed in

areas where contamination is unavoidable.

WARNING:

If installing at an airport, check and follow local guidance for allowed locations for a non-

frangible object 1 m (3.2 ft) tall. Please contact Campbell Scientific if frangible fittings are

required.

4.2 Grounding

The SkyVUE 8M is grounded through its metal feet and ground spikes where used.

SkyVUE™8M Tactical LIDAR Ceilometer 15

Page is loading ...

Campbell Scientific SkyVUE8M Owner's manual

This manual is also suitable for

Campbell Scientific SkyVUE8M Owner's manual

Related papers

Other documents