Botex Converter Media Trigger Owner's manual

Brand: Botex

Model: Converter Media Trigger

Type: Owner's manual

24-004-3041-00

Rev1.0

WebSite:www.botex.com

E-mail:[email protected]

Pleasereadbeforeuse

USER'SMANUAL

English

MIDEA TRIGGER

FUNCTION

Nor mal

Upd ate

-20

0 0 0 0 0 0 0 0 0 0 0 0 0

dB dB dB dB dB dB dB dB dB dB dB dB dB dB

Mas ter

1=Gr ound;2 =Data -;3=Da ta+;4, 5=NC

Med iaTrig ger

DMXI N

AUD IOIN

USB

MID IIN

1.2.3=NC;4=V+;5=Signal

SMP TEIN

1=Gr ound;2 =Data -;3=Da ta+

42Hz

63Hz 107Hz 160Hz 265Hz 400Hz 670Hz

1kHz 1.7kHz

2.5kHz

4.2kHz

6.3kHz 10kHz 16kHz

0dB 10dB

Dou ble

Sin gle

POW ER

3.7) AnalogTriggerEvent(Analog)

ThisallowstodesignatetheinputtedvoltagetocontrolDMXoutputandRelay

aswell. TheVoltageshouldbeintherangeof0-10V.

TheMedia Triggerisabletoidentifythevoltageprecisionof0.05V.

In AnalogConfiguration,

Selectsthe Analog.AnalogNo.:

Selectsthevoltagerange.VoltageL/VoltageH:

SelectsthecontroltypewhichmaybeDMXorRelay.Device:

WhenselectDMX,whichparameterscanrefertotheinstructionsin3.1.

WhenselectRelay,whichparameterscanrefertotheinstructionsin3.6.

Forexample,editaneventasbelow.

Analog1.AnalogNo.:

1.5VVoltageL:

3.0VVoltageH:

DMXDevice:

1DMXFirstCh.:

1Increment:

10DMXLastCh.:

200DMXLevel:

Whentheinputvoltageof Analog1isintherangeof1.5V-3.0V,DMXchannel

1-10 willoutputDMXlevelof200.Whentheinputvoltageisoutofthisrange,

theDMXwill notchange.

Contents

INTRODUCTIONS

Description

MainFeatures

TechnicalFeatures

MechanicalFeatures

Warning

OVERVIEW

OPERATIONGUIDE

SoftwareLaunch

1.FunctionInstructionsofIcon

2.EventName

3.EditEvent

1.1CreateNewEvent

1.2OpenEvent

1.3SaveEvent

1.4DeleteDeviceEvent

1.5UploadEvent

1.6DownloadEventtoDevice

1.7 AddanEventRecord

1.8Delete A Record

FrontView

RearView

Improvementandchangesto

specifications,designandthis

manual,maybemadeatanytime

withoutpriornotice.

Allrightsreserved.

MEADIA TRIGGER

3.1Real Time TriggerEvent(RTC)

3.2 Time TriggerEvent(Time)

3.3MIDI TriggerEvent(MIDI)

3.4 Audio TriggerEvent(AUdio)

3.5Relay TriggerEvent(Relay)

3.6Contact TriggerEvent(Contact)

3.7 Analog TriggerEvent(Analog)

Introduction

ThanksforyourpurchaseofMedia Trigger.Pleasereadtheinstructionsofthis

manualcarefullyandthoroughlybeforeattemptingtooperatethisunit. Keepthis

manualwiththeunit,inordertoconsultitinthefuture.Iftheunitissoldor

giventoanotheroperator,makecertainthatitalwayshasitsmanual,toenable

thenewownertoreadaboutitsoperationandrelativeinstructions.

Built-inrealtimeclockfordate&timetrigger.

ToinputexternaltimeinformationviaSMPTE/LTCorMIDI/MTCforeventtrigger.

CapabilityofMIDINOTEinputfortriggeringdesignatedDMXdata.

Samplesfrom14 Audiobandsaccordingtotheinputed Audiosignaltocontrol

differentDMXchannelsdothattopresentdifferentlightingeffect.

Upto8drycontactsinputforcontrollingdifferentDMXstatus.

Built-in8drycontactsoutputenablestoinputexternalDMXdatatocontrol

thedrycontacts.

Upto4groupsofanalogdata(DC0-10V)fortriggeringdesignatedDMXdata.

EasytoprogramdifferenteventsthroughConfigurationsoftware.

USBtypeBportforcommunicatingwithPC.

ConnectionincludingMIDIIN,SMPTEIN, AUDIOIN,DMXIN&DMXOUT.

MainFeatures

TechnicalFeatures

ElectricalFeatures

PowerInput: AC100~240V50/60Hz

Fuse: T0.5A 250V,20*5mm

InRelayConfiguration,

SelectstheDMXchannel.DMXCh:

DMXLevelLow/DMXLevelHigh: SetstherangeofDMXlevel.

Selectstherelaytobetriggered.RelayNo.:

Selectsthestatusoftherelaytobetriggered.RelayStatus:

Forexample,editaneventasbelow.

DMXCh: 10

DMXLevelLow: 100

120DMXLevelHigh:

1RelayNo.:

OffRelayStatus:

WhentheDMXlevelofthe10thchannelisintherangeof100-120,thecontact

pointof relay1willclose.WhentheDMXlevelofthe10thchannelisoutofthe

rangeof100-120, thecontactpointofrelay1willkeepthestatuswithoutchange.

3.6)ContactTriggerEvent(Contact)

ThisallowstoinputthecontacttotriggerDMX,RelayandMusic.

InContactConfiguration,

SelectstheContact.

SelectsthecontroltypewhichmaybeDMX,Relayor Audio.

WhenselectDMX,parameterscanrefertotheinstructionsin3.1.

WhenselectRelay,

Selectstherelaytobetriggered.

RelayStatus:Selectsthestatusoftherelaytobetriggered.

Whenselect Audio.theEnableandDisableareavailableforoption.

ContactNo.:

Device:

RelayNo.:

Ifselect “onePixel” in “TypeSelect”,eachX-BUBBLEwillbetotallylitonor

off.

Ifselect “MorePixel” in “TypeSelect”,eachX-BUBBLEwillbesegmentally

litonoroff.

3.5)RelayEvent(Relay)

ThisallowstoedittheeventsofwhichtheinputtedDMXcontrolsthecorresponding

Relay.

NEVER try to repair the unit yourself. Repairs by unqualified people could

cause damage or faulty operation. Contact your nearest dealer.

Wait for at least one second to turn on the power after turning off this unit.

DO NOT open the unit--there are no user serviceable parts inside.

Take care not to damage the power cord.

DO NOT make any inflammable liquids, water or metal objects enter the unit.

To prevent fire or shock hazard, do not expose this product under a high

temperature or humidity area.

This product must be earthed.

WARNING

MechanicsFeatures

Size:98mm(L)*482mm(W)*44.5mm(H)

Weight:2KG

Overview

1. TypeBUSBPort

ConnectstoPCthroughUSBcablefordatacommunication.

2.FunctionButton

Keeppressingthisbuttonandpowerontheunitwillaccessprogramupdating

statesothatenabletodownloadprogramfromPCforupdating.Whenthedevice

isrunning,keeppressingandholdingthisbutton,thedevicewillautorectifythe

internalparameters.(Note:pleasedonotinputsoundssignalswhentaking

internalparametersauto-rectifying.)

3.DMXINPort

InputsexternalDMXsignal. TheinputDMXwillassociatewiththosesignal

triggeredbyothermethodsinaccordingtoHTP foroutput.

4.MIDIINPort

InputsMIDInotesignalorMTCinformationofMIDI.

5.SMPTEInPort

Inputsaudiosignal.

6. AudioINPort

Inputsaudiosignal.

7.Double/SingleSelector

Selectsdoubleorsinglechannel.Ifsinglechannelwasselected,therightchannels

datawillfollowthelefttochange.

1 2

6 8

FrontView

In AudioConfiguration,

AudioTrack: Selectstheleftorrightaudiotrack.Whenselect “All”,thehigher

levelintheleftandrightaudiotrackwillbetakenforprocess.sample

Thebandofmusicsample.Eachtrackcontainsof14bands:AudioBand:

16kHz,10.7kHZ,6.3kHZ,4.2kHZ,2.5kHZ,1.7kHZ,1.0kHZ,

670Hz,400Hz,265Hz,160Hz,107Hz,63Hz,42Hz.

OutputDMXsettings:

SelectsthetypeofDMXcontrolwhichwillbethe “OnePixel” ortheTypeSelect:

Pixel”.“More

A lightwhichintensitycanbetotallychanged,thelightingcanbeOnepixel:

flashsynchronouslywiththemusic.madeto

A lightwhichbanbesegmentallylit,thelightingcanbemadeasMorePixel:

wall.music

DMXFirstCh:selectsthestartchannel.

DMXLastCh:selectstheendchannel.

IncrementCh:setsthechangestatusofDMXchannel.

SetX-BUBBLEas16RGBmode,andtheDMXaddressofeachX-BUBBLEiscontinuous.

TheDMXchannelsettingmodecanbeinstructedasfollowingtable.

Forexample,designanengineeringschemeasbelow.

3.3)MIDINoteTriggerEvent(MIDI)

ThisallowstoedittheeventsofwhichMIDINotetriggersDMXoutput.

ThisexternaltimeconsistsofLTCofSMPT andMTCofMIDI.

InMIDINoteConfiguration,

SelectsMIDIchannel.Whenselect “AllChan”,theMIDINote

channelwillbeprocessed.

Selectsthekeynumberwhichwillbeprocessed.

MIDINoteStatus:Key’sstatus.Pressdownthekeythatis “ON”.

ThedefinitionsofDMXparameterscanrefertotheinstructionsin3.1.

MIDIChannel:

MIDINote:

ofevery

3.4) AudioTriggerEvent(Audio)

Thisallowstoedittheeventsofwhichmusic/soundssignaltriggersDMXoutput.

RearView

1=+5 V

2=+3 .3V

3=Si gnal

4=NC

5=GN D

6,7, 8,9=N C

POW ERI N:

AC100- 24 0V ~

50/60 Hz ,10 W

FUSE:

T0.5A 25 0V

20x5m m

RoHS

1=Gr ound;2 =Data -;3=Da ta+;4, 5=NC

DMXOUT

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

INPUT C ON TACTOUT PU T CO NTACT INPUT AN AL OG

1 2 3 4

RCL-1

35 C

(0-10 V)

Madei nChina

CAUT IO N

Risk of Elect ri c S ho ck

DO NOT OP EN

Ne pas o uvrir. Risq ue de choc elec tr iq ue

War ni ng : This unit must be ground ed

1 2

1.OUTPUT CONTACT 1-8

Internalrelaycontactoutputport.Whenthecontactclosed,thecorresponding

Thefollowingparametersareallowed:30VDC/2A,220VDC/0.27A,120VDCLEDlit.

/0.25A./0.5A,250VDC

2.INPUT CONTACT 1-8

Whenthecontactwasputthrough,thecorrespondingLEDlit.

3.INPUT ANALOGport

Inputsvoltageof0-10V.

4.DMXOUT port

OUTPUTSDMXsignal.

5.RCL-1port

ContactstoRCL-1settingsforradiowaveclocksynchronizationsignalinput.

6.Fuseport

Usedtoinstallafuseof500mA 250V.

7.PowerIn

Connectstothepowersourceof AC100-240V50/60Hz.

8.MasterKnob

Mastersthesignalintensityofaudio.

9.Knobforeachband

Adjuststhesignalintensityofeachband.

OperationGuide

SoftwareLaunch

1)FunctionInstructionsofIcon

1.1)CreateNewEvent

Click “CreateNewEvent”iconontheupperleftcorner,thecontentsinthe

EventListwillbeautomaticallycleared.

1.2)OpenEvent

Click “OpenEvent” iconontheupperleftcornertoselectaneventfolderthatthe

contents inthisfolderwillbelistedintheEventList.

DMXFirstCh:theselectedstartchannel.

DMXLastCh:theselectedstopchannel.

IncrementCh:setsDMXchannelchangestatus.

DMXLevel:setstheoutputDMXlevel.

Forexample,settheparametersasbelow:

DMXFirstCh:1

DMXLastCh:5

IncrementCh:1

DMXLevel:200

Whenthiseventwastriggered,theDMXlevelis200forchannel1-5.

Whenthiseventstopped,theDMXlevelis0forchannel1-5.

IfsettheIncrementChannelas2,whentheeventwastriggered,theDMXlevelis

200for channel1,3,5;whentheeventstopped,theDMXlevelis0forchannel1,3,5.

3.2)TimeTriggerEvent(Time)

ThiseventenablestosynchronouslytriggerDMXoutputwiththeexternaltime.

ThisexternaltimeconsistsofLTCofSMPTEandMTCofMIDI.

In TimeCodeConfiguration,the “Start” meansthedesignatedtimetostartandthe

“Stop” meansthedesignatedtimeofend.

In TriggerDMX,thedefinitionsofDMXparameterscanrefertotheinstructionsin3.1.

2)EventName

3)EditEvent

3.1)RealTimeClockTriggerEvent(RTC)

Eacheventcanbedesignatedaname.

ThiseventenablestocontrolDMXoutputthroughthedesignatedtime.

Thiseventcontains:

a.)WeeklyEvent(Theeventwillberepeatedtoperformeveryweek)

b).DatelyEvent(theeventwillbeperformedindesignatedtimeonly.)

Time: thedetailedtriggertimercanbeaccuratetosecond.

thedesignatedtimetostart.Start:

thedesignatedtimetoend.Stop:

InWeeklyEvent,ifthestarttimeisbiggerthantheendtimethatcancarry out

thetriggerovertothenextday.

Forexample,editaWeeklyevent:

TimeStart:20:30:00 TimeStop:08:30:00

Thus,thisweeklyEventwillstartat20:30:00andstopat08:30:00ofthe next

day.

1.3)SaveEvent

Click “Save” iconontheupperleftcornertoselectapropereventthatthecontents

ofthiseventcanbesavedinthefolder.

1.4)DeleteDeviceEvent

Click “DeleteDeviceEvent”iconmaydeleteatypeofeventfromdevice.

Note: ToperformthisfunctionthedevicemustconnecttoPC.

1.5)UploadEvent

Click “UploadEvent” icontoselectaproperfolderthatwillreadatypeofevent

fromdevice.

Note: ToperformthisfunctionthedevicemustconnecttoPC.

1.6)DownloadEventtoDevice

Click “DownloadEventtoDevice” icontoselecteventfolderthattheeventwillbe

downloadedtodevice.

Note: ToperformthisfunctionthedevicemustconnecttoPC.

1.7) AddanEventRecord

Wheneditinganevent,click “Add” willaddaneventintoeventlist.

1.8)DeleteaRecord

Toselcetaneventineventlistandthenclick “DEL” willdeleteanevent.

Botex Converter Media Trigger Owner's manual

Botex Converter Media Trigger Owner's manual

Botex Converter Media Trigger Owner's manual

Related papers

Other documents