Kicker 46HDBL Owner's manual

46HDBL
Kicker
Brand
Kicker
Model
46HDBL
Category
Car speakers
Type
Owner's manual

This manual is also suitable for

Kicker 46HDBL69 is a motorcycle lid kit designed for Harley Davidson® Motorcycles 2014–Present. It allows for the installation of speakers in the motorcycle's saddlebags, enhancing the audio experience while riding. The kit includes all necessary hardware and detailed instructions for a straightforward installation process. The speakers feature a weather-resistant design, ensuring durability and reliable performance in various weather conditions. Get ready to elevate your motorcycle's sound system and enjoy an immersive audio experience on your rides with the Kicker 46HDBL69.

Kicker 46HDBL69 is a motorcycle lid kit designed for Harley Davidson® Motorcycles 2014–Present. It allows for the installation of speakers in the motorcycle's saddlebags, enhancing the audio experience while riding. The kit includes all necessary hardware and detailed instructions for a straightforward installation process. The speakers feature a weather-resistant design, ensuring durability and reliable performance in various weather conditions. Get ready to elevate your motorcycle's sound system and enjoy an immersive audio experience on your rides with the Kicker 46HDBL69.

1. Remove the factory lids, latch, and hinge
assembly.
2. Install the factory latch and hinge assembly to
your new KICKER lids using the factory screws.
3. Install the speakers by rotating the speaker
from the back side of lid, through the opening of
the lid, positioning the speaker to line up with the
holes. Install the two front screws through the
speaker into the lid.
HDBL | HDBL69
HDBLVB | HDBLVB69
Motorcycle Lid Kit Installation Guide for Harley Davidson
®
Motorcycles 2014–Present
Important: Over-tightening mounting fasteners may result in damage to your motorcycle. Please refer to your service manual for proper procedures and torque
specifi cations. KICKER is not responsible for damage resulting from improper installation techniques. This kit may not be compatible with some aftermarket
head units. KICKER cannot be held responsible for any damage to painted surfaces during removal or addition of KICKER parts.
4. Place the bracket on the back side of the speaker. Install a bolt through the bracket and speaker from the back side, then
position the speaker nut on top and tighten. Using the factory screw, attach the outside of the bracket to the lid.
5. install the factory latch lever using the factory screw and supplied rubber grommet.
6. Install the supplied grilles to the lids using
the supplied screws.
46HDBL-E-20200327
7. If you have installed the KICKER Front Kit,
locate the 4-pin connector under the seat of
the motorcycle. Connect the included wiring
harness to the 4-pin plug under the seat of
the motorcycle. Connect the portion of the
harness that will connect the lid speakers
to the front amp, and route the left and right
2-pin connectors to a location adjacent to the
bag attachment area of the motorcycle.
Note: If not already fl ashed for rear speakers, it will now be necessary to fl ash the motorcycle for 4-speaker set up using the
KICKER fl ash programmer of the Techno Research Centurion. Follow instructions for Flash Programmer to complete this task.
Set the gain to optimize sound quality and enjoy!
8. Drill a 3/4” hole in each bag as pictured and install the supplied
rubber gromets.
9. Using the included zip tie mounts and zip ties, route each wire as
show in the picture to secure the bag harness.
10. Install the lids to the bags.
11. Connect the speaker wires to the speaker (the terminals are
sized for the correct terminal), route the wire to the opposite side of
the speaker and secure it with a zip tie to the square hole in the tab
at the base of the magnet to ensure the wire does not get caught
on any gear in the bag.
  • Page 1 1
  • Page 2 2

Kicker 46HDBL Owner's manual

46HDBL
Kicker
Brand
Kicker
Model
46HDBL
Category
Car speakers
Type
Owner's manual
This manual is also suitable for

Kicker 46HDBL69 is a motorcycle lid kit designed for Harley Davidson® Motorcycles 2014–Present. It allows for the installation of speakers in the motorcycle's saddlebags, enhancing the audio experience while riding. The kit includes all necessary hardware and detailed instructions for a straightforward installation process. The speakers feature a weather-resistant design, ensuring durability and reliable performance in various weather conditions. Get ready to elevate your motorcycle's sound system and enjoy an immersive audio experience on your rides with the Kicker 46HDBL69.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents