AIPTEK 3D iH3 Owner's manual

1

ENGLISH

Welcome:

Dear user, thank you for purchasing this product. Much investment in time and effort has

gone into its development, and it is our hope that it will give you many years of trouble-free

service.

FCC Compliance Statement:

This device complies with Part 15 of the FCC Rules. Operation is subjected to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part

15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference

in residential installations. This equipment generates, uses, and can radiate radio frequency energy, and

if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause interference to radio or television equipment reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Move the equipment away from the receiver.

- Plug the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/television technician for additional suggestions.

You are cautioned that any change or modiﬁ cations to the equipment not expressly approved by the party

responsible for compliance could void Your authority to operate such equipment.

If the time arises to throw away your product, please

recycle all the components possible.

Batteries and rechargeable batteries are not to be

disposed in your domestic waste! Please recycle them at

your local recycling point.

Together we can help to protect the environment.

Safety Notice:

1. Do not drop, puncture or disassemble the camcorder; otherwise the warranty will be voided.

2. Avoid all contact with water, and dry hands before using.

3. Do not expose the camcorder to high temperature or leave it in direct sunlight. Doing so may damage the

camcorder.

4. Use the camcorder with care. Avoid pressing hard on the camcorder body.

5. For your own safety, avoid using the camcorder when there is a storm or lightning.

6. Do not use batteries of different speciﬁ cations. Doing so may lead to the potential for serious damage.

7. Remove the battery during long periods between usage, as a deteriorated battery may affect the

functionality of the camcorder.

8. Remove the battery if it shows signs of leaking or distortion.

9. Use only the accessories supplied by the manufacturer.

10. Keep the camcorder out of the reach of infants.

11. Risk of explosion if battery is replaced by an incorrect type.

12. Dispose of used batteries according to the instructions.

ENGLISH

2

Extra notice regarding 3D viewing:

1. To view 3D display and receive 3D effects well, the viewer should be positioned to face the center of the

screen at around 30 cm distance and not having a steep viewing angle.

2. Viewing in 3D mode may cause dizziness or even perceptive after effects, disorientation, and eye strain. It

is recommended that viewers take frequent breaks to alleviate the likelihood of these effects. If you have

any of the above symptoms, immediately cease usage of the 3D display of this device and do not resume

until the symptoms have receded.

3. Do not use the Red/Cyan Glasses for any purpose other than viewing red/cyan 3D ﬁ les. Wearing the Red/

Cyan Glasses for any other purpose (such as general spectacles, sunglasses, protective goggles, etc.)

may cause harm to you or weaken your eyesight.

4. Young children viewing 3D ﬁ les should always be accompanied by adults. It is not recommended to give

this device into the hands of young children.

The 3D display technology used in this product:

This product utilizes the “Parallax Barrier” 3D technology.

A parallax barrier is a device that allows a liquid crystal

display (LCD) to show a stereoscopic image without the

need for the viewer to wear a pair of 3D glasses. Placed

in front of the normal LCD, a parallax barrier consists of

a layer of material with a series of precision slits, allowing

each eye to see a different set of pixels, thus creating a

sense of depth and 3D effect through parallax.

Tips to Obtain the Best 3D Effects with your Camcorder

 Optimal watching distance to the monitor of 3D Camcorder:

Keep your eyes distance approximately 30cm from 3D camcorder (half the length

of your arm) (as shown in right ﬁ gure).

 The ideal viewing distance for best 3D effects:

The different distances maintained between the camcorder: 1.5 to 2 meters for foreground, 1 to 2 meters for

the foreground to the medium shot, and over 4 meters for the long shot (as shown in ﬁ gure below).

Therefore, multi-perspective images can be obtained via the above shooting skills. In order to obtain the best

3D effects, keep your hands still and steady when recording.

Parallax Barrier

Pixels

Right

Left

Right eye

Left eye

3

ENGLISH

Refer to two below illustrations for reference:

Long shot

Medium shot

Foreground

Note

Users can toggle between 3D mode and 2D mode by pressing the 3D/2D switch button. Since 3D grating ﬁ lm will be •

automatically enabled under 3D mode, the brightness of monitor in 3D mode will be less than in 2D mode; nevertheless,

quality of the 3D ﬁ les shot/recorded will remain the same.

ENGLISH

4

Contents

Getting Started ............................................................................................ 5

Product Overview ....................................................................................................................5

Inserting the Battery and Memory Card ..................................................................................6

Charging the Battery ...............................................................................................................6

Turning on/ off the Camcorder ................................................................................................7

Setting the Language ...............................................................................................................7

Setting the Date and Time ......................................................................................................8

LCD Display ............................................................................................................................8

Basic Operations ...................................................................................... 10

Switching 2D/3D Mode .........................................................................................................10

Recording Videos ..................................................................................................................10

Viewing Photos ..................................................................................................................... 11

Playing Back Videos ............................................................................................................. 11

Deleting Files ........................................................................................................................ 11

Using the Menu .....................................................................................................................12

Transferring Files to Your Computer ..................................................................................... 13

Connecting to HDTV .............................................................................................................14

Appendix ................................................................................................... 15

Battery Life ............................................................................................................................15

Possible Number of Shots ....................................................................................................15

Troubleshooting ....................................................................................................................15

Speciﬁ cations ........................................................................................................................16

5

ENGLISH

Product Overview

1. Hand Strap Mount

2. Lens (only for 3D mode)

3. LED Light x2

4. Lens

5. Flash

6. Microphone x2

7. LCD Panel

8. Speaker

9. Power Button

10. Delete Button

11. Playback Button

12. Zoom Button

13. Shutter Button

14. LED indicator

15. Record Button

16. Micro USB Port

17. HDMI Port

18. Navigation Key

19. 3D/2D Switch Button

20. Tripod Socket

21. SD Card Compartment

22. Battery Compartment

Getting Started

21 43 65

Navigation key (hot key):

A. Up: Icon on/off

B. Left: LED light on/off

C. Down: Flash mode (off/

auto/on)

D. Right: Menu mode

7 8 12 13 14 159 10 11

16 17 1918

A B DC

222120

6

ENGLISH

Inserting the Battery and Memory Card

1 Open the LCD panel.

2 Turn off the power.

3 Open the battery cover as shown in the illustration.

4 Insert an SD card (sold separately) into the SD card

compartment until it clicks into place.

5 Insert the battery. Make sure that the + and – symbols

on the battery line up with the + and – symbols on your

camcorder.

6 Close the battery cover.

Note

Once you open the battery cover, the power of camcorder will be cut off.•

Charging the Battery

Before charging:

Make sure that the camcorder is turned off and the battery is inserted before starting.•

Before charging via computer, be sure that the computer is turned on.•

It is recommended to charge the battery for at least 8 hours before the ﬁ rst time usage.•

1 Open the LCD panel.

2 Turn off the power.

3 Open the I/O cover.

4 Plug the Micro USB connector to the Micro USB port of

your camcorder using the Micro USB cable.

5 Charge the battery. Choose one of the following two

options:

A. Using the AC adapter

i. Plug the other end of the USB cable to the AC adapter.

ii. Plug the AC adapter to a wall outlet to start charging.

1

2

3

4

5

1

2

3

4

7

ENGLISH

B. Using the computer

Plug the other end of the USB cable to a computer/

notebook to start charging.

Checking the remaining battery charge:

A remaining charge indicator appears on the upper right of the LCD screen when power on camcorder.

The displayed battery remaining indicator may not be correct under certain circumstances.

•

The ﬂ ash strobe & video light will be disabled in low battery. •

To avoid sudden outage of power supply, you are recommended to replace the battery when the icon•

indicates low battery life.

Turning on/ off the Camcorder

Press and hold the Power Button to turn the camcorder on/off.

Note

Closing and opening the LCD panel can power on/off the camcorder.•

Setting the Language

To select the language, do the following:

1 Open the LCD panel to turn the camcorder on.

2 Press the Right key to open the menu.

3 Press the Right key to enter System Setting ( ).

4 Press the Down key to select Language and press the OK

key.

5 Press the Up/Down key to select the desired language and

press the OK key to conﬁ rm.

English

ᓄ̚

ᖎ̚

Deutsch

Français

Italiano

Move Exit

Language

LED indicator

When the battery is charging, the LED indicator turns on (orange). •

When the battery is fully charged, the LED indicator turns off.•

High Low

Navigation key:

A. Up

B. Left

C. Down

D. Right

A B DC

8

ENGLISH

Date

7

Month

15

Date

2011

Year

Time

18

hours

46

min

Date

Time

Setting the Date and Time

To adjust the date and time, do the following:

1 Open the LCD panel to turn the camcorder on.

2 Press the Right key to open the menu.

3 Press the Right key to enter System Setting ( ).

4 Press the Up/Down key to select Date or Time and press the

OK key.

5 Press the Left/Right key to select the ﬁ eld to be adjusted.

6 Press the Up/Down key to adjust the value.

7 Repeat steps 5-6 to adjust other desired ﬁ elds.

8 Press the Shutter Button to exit.

LCD Display

Icons are displayed on the screen to indicate the camcorder status/settings.

1. Mode

[

] 3D mode

[

] 2D mode

2. Video resolution

[

] Full HD (1920x1080p)@30fps

[

] HD 720P(1280x720p)@60fps

3. Date stamp

[

*no icon] Date stamp is disabled

[

] Print a date mark

[

] Print a date and time mark

4. Self timer

[

*no icon] Self timer is disabled

[

] 10-second delay self timer

5. Slide show

[

*no icon] Slide show is disabled

[

] Playback in slide show mode

00:50:50

1 2 3 4 5 6 7 8 9 10

11 12 13

Preview Mode - Video/Photo

00:00:07

1 233 4 5 6 7 8 9 10

15 14 13

Recording Mode

9

ENGLISH

6. Video light

[

*no icon] Video light is disabled

[

]

The setting allows you to add extra light

when the lighting is insufﬁ cient while

recording video clips.

7. Flash mode

[

] Flash off

[

]

Auto ﬂ ash (When the icon is blinking, it

indicates that the ﬂ ash is being charged.)

[

]

Forced ﬂ ash (When the icon is blinking, it

indicates that the ﬂ ash is being charged.)

8. White balance

[

] Auto white balance

[

]

Sunny (It suitable for outdoor recording in

sunny weather.)

[

]

Cloudy (It is suitable for recording in

cloudy weather or shady environments.)

[

]

Fluorescent (It is suitable for indoor

recording with ﬂ uorescent lamp

lighting, or environments with high color

temperature.)

[

]

Tungsten (It is suitable for indoor

recording with incandescent lamp

lighting, or environments with low color

temperature.)

9. Media type

[

] Memory card

[

] Internal memory

[

] Memory card error

[

] Memory card locked

10. Battery status

[

] Full battery power

[

/ ] Medium battery power

[

/ ] Low battery power

11. Guide key

[

]

Press the Right key to enter menu mode.

12.

Available recording time (The available recording time

varies depending the image complexity.)

13. Zoom status

14. Elapsed time (recording)

15. Guide key

[

] Press the OK key to pause recording.

[

] Press the OK key to resume recording.

16. File type

[

] Video ﬁ le

[

] Photo ﬁ le

17. File number/total ﬁ les

0001/0100

1 16 17 9 10

18 19

Playback Mode

(Thumbnail display)

0001/0100

00:00:10

1 16 17 9 10

21 19 20

Playback Mode

(Full screen display - Video)

0001/0100

1 16 17 9 10

19

Playback Mode

(Full screen display - Photo)

18. Guide key

[

]

Press the OK key to enter Full screen mode.

19. Guide key

[

]

Press the Shutter Button to return to

preview mode.

20. Elapsed time (playback)

21. Guide key

[ ]

Press the OK key to pause video playback.

[

]

Press the OK key to resume video playback.

10

ENGLISH

Switching 2D/3D Mode

Press the 3D/2D Switch Button to toggle between 2D and 3D

modes.

In Playback mode, press the 3D/2D Switch Button to toggle

between viewing 2D or 3D ﬁ les stored in your camcorder.

Note

In 2D mode, the camcorder only uses the right lens to record videos or take photos.•

The 3D ﬁ les cannot be recorded/viewed/deleted in 2D mode, and vice versa. The 2D and 3D ﬁ les are stored separately.•

This camcorder utilize• s the “Parallax Barrier” 3D technology. The parallax barrier is a special layer placed in front of the

LCD screen. In 3D mode, it allows each of your eye to see a different set of pixels on the screen (hence the 3D effect). The

brightness of the screen seems to be halved in 3D mode.

Taking Photos

1 Turn on the camcorder.

2 Compose your image.

Use the

• Zoom Button to zoom in and out on the subject.

3 Press the Shutter Button to capture a photo.

Note

To avoid fuzzy photos, please hold the camera steady or use a tripod.•

In ord• er to optimize the 3D effect, the ideal shooting range is 1m~4m (3ft~13ft), and you are advised to take photos with

sufﬁ cient light.

Recording Videos

1 Turn on the camcorder.

2 Compose your image.

3 Press the Record Button to start recording the video.

a. Use the Zoom Button to zoom in and out on the

subject.

b. To pause video recording, press the OK key. Press the

OK key again to resume recording.

c. When recording videos in a dark environment, press

the Left key to turn on video light to provide extra light

to the subject.

4 To stop video recording, press the Record Button again.

Basic Operations

2

3

1

3

a

3

b

3

c

Note

The engine will auto stop recording a video in 30 minutes.•

11

ENGLISH

Viewing Photos

1 Turn on the camcorder.

2 Press the Playback Button to enter the playback mode.

3 Use the Left/Right/Up/Down key to browse the recorded ﬁ les.

Press the

• 3D/2D Switch Button to switch to 2D or 3D ﬁ les.

4 Press the OK key to view the photo in full screen.

Use the

• Zoom Button to zoom in the selected photo. When the image is zoomed in, the direction keys

appear on the LCD screen. Use the Left/Right/Up/Down key to view the zoomed image. To exit zoom

mode, press the OK key to return into its original size.

5 Press the Left/Right key to view other photos.

Note

Zoom playback is only available in 2D photo mode.•

Playing Back Videos

1 Turn on the camcorder.

2 Press the Playback Button to enter the playback mode.

3 Use the Left/Right/Up/Down key to browse the recorded ﬁ les.

4 Press the OK key to play the selected video clip.

To pause during playback, press

• the OK key. To resume, press the OK key again.

To rewind/fast forward, press and hold the

• Left/Right key.

To adjust the volume during playback, use the

• Zoom Button.

5 Press the Shutter Button to return to the thumbnail mode.

Deleting Files

1 Turn on the camcorder.

2 Press the Playback Button to enter the playback mode.

3 Use the Left/Right/Up/Down key to browse the recorded

ﬁ les.

Press the

• 3D/2D Switch Button to switch to 2D or 3D ﬁ les.

4 Press the Delete Button to delete the selected ﬁ le. The

Delete menu appears on the screen.

To delete the selected ﬁ le, select

• Yes.

To exit menu without deleting the selected ﬁ le, select

• Cancel.

To delete all ﬁ les (in the same folder), select

• All.

5 Press the OK key to conﬁ rm.

3

2

12

ENGLISH

Note

Once the ﬁ le is deleted, it cannot be recovered.•

If you select “All”, all ﬁ les in the same folder (2D or 3D) will be deleted. •

Using the Menu

1 Press the Right key to open the menu screen.

2 Press the Left/Right key to select the Basic Setting/System Setting.

3 Press the Up/Down key to select the setting item and press the OK key to enter.

4 Press the Up/Down key to set/adjust the setting and press the OK key to conﬁ rm.

5 Press the Shutter Button to exit.

Basic Setting

Option Description

Video Resolution Set the video resolution (Full HD 30f / HD 720P 60p).

Flash Strobe Set the ﬂ ash mode (Off / Auto / On).

Video Light Enable/disable video light (Off / On).

White Balance

Set the white balance when capturing images under speciﬁ c lighting conditions (Auto / Sunny

/ Cloudy / Fluorescent / Tungsten).

NightShot Enable/disable night shot (Off / On).

Date Stamp

Disable/set the date stamp type when taking a photo and recording a video (Off / Date /

TIME/DATE).

Selftimer

Enable/disable the selftimer (10-second delay) when shooting a photo and recording a video

(Off / On).

Slide Show Enable/disable slide show in Playback mode (Off / On).

Video Resolution

Flash Strobe

Video Light

White Balance

NightShot

Date Stamp

Move Exit

Selftimer

Slide Show

Move Exit

Navigation key:

A. Up

B. Left

C. Down

D. Right

A B DC

13

ENGLISH

System Setting

Option Description

Language Set the on-screen display language.

Date Set the current date.

Time Set the current time.

Icon Hide/unhide icon display on the screen (Off / On).

Start Image Enable/disable start image feature when turning the power on (Off / On).

Auto Off

If “Auto Sleep” is set to “On” and the camcorder is left idle for 3 minutes, the camcorder will

automatically turn off (Off / On).

Beep Enable/disable sound when pressing any key (Off / On / Shutter On).

Frequency

Select the TV standard according to your region (60 Hz / 50 Hz).

Note

60 Hz - for the United States, Taiwan, Japan, Korea, and other regions.•

50 Hz - Europe, China, Hong Kong, and other regions.•

Format

Format your memory card or the internal memory when no memory card is inserted (No /

Yes).

Default Reset the camcorder to factory defaults (No / Yes).

Transferring Files to Your Computer

1 Open the I/O cover.

2 Plug the Micro USB connector to the Micro USB port of your

camcorder using the Micro USB cable.

3 Plug the other end of the USB cable to a computer/notebook.

4 Turn on the camcorder.

5 From the Windows desktop, browse for My Computer >

Removable Disk.

You can access all ﬁ les stored in the camcorder.•

Language

Date

Time

Icon

Start Image

Auto Off

Move Exit

Beep

Frequency

Format

Default

Move Exit

14

ENGLISH

Connecting to HDTV

1 Turn on your HDTV.

2 Connect the HDMI-in connector (the larger end) of the HDMI cable to the HDTV.

3 Connect the other end of the HDMI cable to your camcorder.

4 Turn on the camcorder.

5 On your HDTV, select the HDMI input port where the HDMI cable is connected.

6 Switch your camcorder to Playback mode and start to play a ﬁ le.

Note

If your HDTV is 2D type, the 3D ﬁ les output on your HDTV will be 2D “side-by-side” only.•

The HD TV will display your video clips in 1080i (60 ﬁ elds) resolution mode although it is recorded in 1080P (30 frames) or •

720P (60frames) setting.

15

ENGLISH

Battery Life

 Still image (without ﬂ ash)  Video clip

Number of shots: 400 Recording time (minute): 50

* The unit is set to 3D mode.

Note

This table is for your reference only. The actual battery life depends on your battery quality and recharge level.•

Possible Number of Shots

Memory card

capacity

Video clip (Full HD)

(min.)

Video clip (HD 720P)

(min.)

Still image

2GB

25 min. 26 min. 1500

4GB

50 min. 52 min. 3000

8GB

100 min. 104 min. 6000

16GB

200 min. 208 min. 12000

Note

The actual value of capacity may vary (up to ± 30%) depending on the color saturation and complexity of your subject and •

surroundings

.

Troubleshooting

Problem Possible cause Solution

Cannot to view the 3D video/

photo playback using my 3D

HDTV.

The system of your 3D TV/

display is not correctly set

up to support the 3D ﬁ le

format.

Select “side-by-side” setting in your 3D HDTV/

display to correctly display the 3D effect.

Cannot view the 3D videos/

photos on my 3D-featured

PC/notebook.

The PC/notebook does not

support “side-by-side” 3D

format or the system is not

correctly set up.

If your 3D PC/notebook is “Nvidia 3D” •

compatible, you can set the TotalMedia

HDCam program to support “Nvidia 3D”

directly.

If your PC/notebook is not “Nvidia 3D” •

compatible, you may consider installing

“Nvidia 3D kit” to support the 3D effect.

You can download and install the 3D •

freeware “Stereoscopic Player”, and set up

the software to support “side-by-side” 3D

effect.

Flash occurs when I wear my

Shutter Glasses (that came

with 3D HDTV/display) to

watch 3D ﬁ les.

You are watching 3D

ﬁ les under 50Hz or 60Hz

ﬂ uorescent light.

Turn off the ﬂ uorescent light to avoid

interference and then watch the 3D ﬁ les.

Appendix

16

ENGLISH

Speciﬁ cations

Image Sensor Dual 5 Mega-pixels CMOS (2592 x 1944)

Resolution

Camcorder:

Full HD(1920x1080)

HD 720p(1280x720)

Camera: 3.7M (16:9)

File Format MP4(H.264), JPEG

Video Frame Rate

Full HD up to 30fps

HD 720p up to 60fps

Internal Memory 128MB built-in; 9MB for storage

3D/2D capture Yes, switchable

External Memory SD card slot (supports 256MB up to 32GB SD/SDHC)

LCD Display 3.2” 3D TFT panel supports 3D and 2D mode display

Lens Dual Fixed focus lens

Focus Range 1 m ~ 

Aperture Range F3.2; f=5.23mm

Shutter Speed 1 ~ 1/2000 sec.

Flash Light Auto / Off / On for pictures

LED Light 2xLED light for Video

Digital Zoom

10X for 2D mode

4X for 3D mode

Night Shot Mode On, Off

White Balance Auto, Sunny, Cloudy, Fluorescent, Tungsten

Date Stamp Yes for still picture and video

Microphone Yes; stereo microphone built-in

Speaker Yes

TV out HDTV (HDMI output)

Self-timer Off, 10 sec

Power Save Mode 3 min

Interface USB 2.0 mass storage

Battery

NP40 1200mA Li-lon rechargeable Battery

Operating Condition:

Temperature / Humidity

0~40°C/ 80%

Storage Condition:

Temperature / Humidity

1 month -20°C ~ + 60°C / 85%

3 months -20°C ~ +45°C / 80%

1 year -20°C ~ + 25°C / 70%

Dimensions (LxWxH) 130mm x 53mm x 67mm (5.12” x 2.09” x 2.64”)

Weight (included battery) 380g

* The speciﬁ cations are subject to change without prior notice.

Page is loading ...

5

ㆶ։ѣᮽ

ӝ૷Ᾰ㿾

1. ᢁᑜᆿ㻻ᓝ

2. 䮒ཪδӻ䘸⭞ӄ3D⁗ᕅε

3. LED ᤽⽰⚥x2

4. 䮒ཪ

5. 䰠ݿ⚥

6. 哜ށ伄x2

7. ⏨Წ䶘ᶵ

8. ᢢ༦ಞ

9. ⭫Ⓠ䭤

10. ࡖ䲚᤿䫤

11. ᫣᭴䭤

12. ਎❜䭤

13. ᘡ䰞᤿䫤

14. LED᤽⽰⚥

15. ᖋ࡬᤿䫤

16. Micro USBㄥਙ

17. HDMI ㄥਙ

18. ሲ㡠䭤

19. 3D/2D࠽ᦘ᤿䫤

20. п㝐ᷬᆊ

21. SDগᨈ″

22. ⭫⊖″

߼༽ֵ⭞

21 43 65

ሲ㡠䭤δ✣䭤εφ

A. ੇр䭤φ ഴḽᔶ/ީ

B. ੇᐜ䭤φ LED ᤽⽰⚥ᔶ/ީ

C. ੇс䭤φ 䰠ݿ⁗ᕅ

δީ䰣/㠠ࣞ/ᔶ੥ε

D. ੇ਩䭤φ 㨒ঋ⁗ᕅ

7 8 12 13 14 159 10 11

16 17 1918

A B DC

222120

Page is loading ...

16

ㆶ։ѣᮽ

㿺Ṳ

ഴ܅Ֆ᝕ಞ ਂ500н܅㍖CMOS (2592 x 1944)

࠼䗞⦽

᩺܅ᵰφ

Full HD (1920x1080)

HD 720p(1280x720)

᩺܅ཪφ 3.7M (16:9)

ᮽԬṲᕅ MP4 (H.264), JPEG

㿼仇ᑝ䙕⦽

Full HDθᴶ儎30fps

HD 720pθᴶ儎60fps

޻㖤䰠ᆎ ޻㖤128MBχ9MBᆎ۞

3D/2Dᦋ㧭 ᱥθਥ࠽ᦘ

ཌ䜞ᆎ۞ಞ SDগᨈ″δ᭥ᤷ256MBθᴶཝ32GB SD/SDHCε

⏨Წᱴ⽰ኅ 3.2Ĉ 3D TFT䶘ᶵ᭥ᤷ3Dૂ2D⁗ᕅᱴ⽰

䮒ཪ њѠᇐ❜䮒ཪ

❜䐓㤹പ 1 m ~ ĺ

ݿാ㤹പ F3.2χf=5.23mm

ᘡ䰞䙕ᓜ 1 ~ 1/2000〈

䰠ݿ⚥ δ➝⡽ε㠠ࣞ/ީ䰣/ᔶ੥

LED ᤽⽰⚥ 2Ѡ㿼仇⭞LED᤽⽰⚥

ᮦ⸷਎❜

2D⁗ᕅсѰ10X

3D⁗ᕅсѰ4X

དྷᲥ⁗ᕅ ᔶ੥θީ䰣

ⲳᒩ㺗㠠ࣞȽᲪཟȽ䱪ཟȽ㦝ݿ⚥Ƚⲳ⛳⚥

ᰛᵕᢉদ ᱥδ䘸⭞ӄ䶏↘➝⡽ૂ㿼仇ε

哜ށ伄 ᱥχ޻㖤㄁։༦哜ށ伄

ᢢ༦ಞ ᱥ

⭫㿼䗉࠰ HDTVδHDMI䗉࠰ε

ᇐᰬ㠠ᤃ ީ䰣θ10〈

ⴷ⭫⁗ᕅ 3࠼䫕

᧛ਙ USB 2.0ཝᇯ䠅ᆎ۞

⭫⊖

NP40 1200mA䬸⿱ᆆݻ⭫⭫⊖

䘆㺂ᶗԬφ

⑟ᓜ/⒵ᓜ

0~40eC / 80%

䍤ᆎᶗԬφ

⑟ᓜ/⒵ᓜ

1 Ѡᴾ -20

eC ~ + 60eC / 85%

3 Ѡᴾ -20eC ~ +45eC / 80%

1 ᒪ -20eC ~ + 25eC / 70%

ཌᖘተሮ(LxWxH) 130mm x 53mm x 67mm (5.12Ĉ x 2.09Ĉ x 2.64Ĉ)

䠃䠅(ऻᤢ⭫⊖) 380g

* 㿺Ṳྸᴿ਎ᴪθᚋуਜ㺂䙐⸛Ⱦ

AIPTEK 3D iH3 Owner's manual

This manual is also suitable for

AIPTEK 3D iH3 Owner's manual

in other languages

Related papers

Other documents