Whirlpool KBT 6424 DO IX User guide

Page is loading ...

12

Advice and recommendations

• This appliance is intended for non-professional

use within the home.

• Before using your appliance, read the instructions in

this owner’s manual carefully since you will find all

the instruction you require to ensure safe installa-

tion, use and maintenance. Always keep this owner’s

manual close to hand since you may need to refer to

it in the future.

• After having removed the packaging, check that the

appliance is intact. If in doubt, do not use the appli-

ance and contact professionally qualified personnel.

•

Never leave the packaging components (plastic bags,

foamed polystyrene, screws, etc.) within the reach

of children since they are a source of potential dan-

ger.

• The appliance must be installed only by a qualified

person in compliance with the instructions provided.

•

The manufacturer declines all responsibility for im-

proper installation which may harm persons and ani-

mals and damage property.

• The electrical safety of this appliance can only be

guaranteed if the appliance itself is correctly earthed,

in compliance with regulations on electrical safety.

Always ensure that this fundamental safety require-

ment is satisfied; if you have any doubts call in a

qualified technician to check the system thoroughly.

•

The manufacturer denies all responsibility for dam-

age resulting from a system which has not been

earthed.

• Before connecting the appliance, make sure that the

technical data on the plate correspond to the charac-

teristics of the electricity mains.

• Check that the electrical capacity of the system and

sockets will support the maximum power of the ap-

pliance, as indicated on the data plate. If in doubt,

contact a qualified professional.

• This appliance must be used for the purpose for which

it was expressly designed. Any other use (for exam-

ple: heating rooms) is considered to be improper and

consequently dangerous.

First use: the glue that is applied on the gaskets leaves some traces of grease on the glass. Before using the

appliance, we recommend you eliminate these with a special non-abrasive maintenance product. During the first

few hours of use there may be a smell of rubber which will disappear very quickly.

•

The manufacturer declines all responsibility for dam-

age resulting from improper and irresponsible use.

• A number of fundamental rules must be followed when

using electrical appliances. The following are of par-

ticular importance:

• do not touch the appliance with wet hands;

• do not use the appliance when barefoot

• avoid using extension leads

• never pull the power supply cable or the appliance to

unplug the appliance plug from the mains;

• never leave the appliance exposed to atmospheric

agents (rain, sun etc.);

• do not allow children or persons who are not familiar

with the appliance to use it, without supervision.

• Always unplug the hob from the mains or switch off

the main switch before cleaning or carrying out main-

tenance operations.

• If a crack develops on the surface of the glass,

disconnect the appliance immediately. For repairs,

call only authorised after-sales servicing centres and

request the use of original spare parts only. Failure

to comply with these conditions may compromise the

safety of the appliance.

• If you are no longer using an appliance of this type,

remember to make it unserviceable by unplugging

the appliance from the mains and cutting the supply

cable. Also make all potentially dangerous parts of

the appliance harmless, in particular for children who

could play with the appliance.

• The glass ceramic top is resistant to thermal as

well as mechanical shocks. However, it can break

if struck violently with a sharp object, such as a

tool. If this happens, disconnect the appliance

from the power supply and contact an authorised

after-sale service centre to carry out repairs.

• Do not forget that the temperature of the cooking zone

remains high for at least half an hour after it has been

turned off, take care not to inadvertently place pans

or items on this hot surface.

• Do not turn on the cooking surfaces if there are sheets

of aluminium foil or plastic objects on the hob.

• Do not get too close to the hot areas of the hob.

• When using small electrical household appliances

close to the hob, ensure that the power cable does

not come into contact with the hot surfaces

• Make sure you turn the handles of pots and pans

inwards to avoid knocking them over accidentally.

13

The following instructions are intended for a qualified

fitter to guide him/her along the installation, adjustment

and technical maintenance procedures as correctly as

possible and in full compliance with the applicable norms

in force.

Important : unplug the hob before all operations.

Installation

• This hob can be built into a worktop simply by cutting

out the corresponding slot.

• The worktop must be made with a material designed

to withstand a temperature of approximately 100°C.

• The hob should be positioned at least 40 mm away

from the back wall or any other vertical surface in

order to allow for correct ventilation and to prevent

the surfaces around the appliance from overheating.

• If you wish to install the hob on top of an oven, the

latter must be fitted with a cooling fan.

• Try to avoid installing the hob on top of a dishwasher;

if this is unavoidable, place a watertight separating

element between the two appliances.

10

Distance to

keep between the

cut-out slot and

the cabinet

Fastening

Very important: It is vital that you ensure the glass

ceramic hob is built into a perfectly flat supporting sur-

face.

Deformations due to improper fastening could alter

the characteristics of the hob and compromise its per-

formance.

The fastening springs are fastened by screws (see dia-

gram).

It is vital that these screws be kept accessible at all

times.

Insert the hob into the cut-out slot, applying pressure all

along the perimeter of the hob frame so that the latter

adheres fully to the worktop.

FRONT OF HOB

KITCHEN

WORKTOP

30

40

REAR SPRING ASSEMBLY

HOB FROM BELOW

Installation and fastening

560 +/- 1

490 +/- 1

48

590

520

560 +/- 1

490 +/- 1

48

574

504

690

520

560 +/- 1

490 +/- 1

48

785

750 +/- 1

510

490+/- 1

48

14

Technical characteristics

Electrical connection

• The electrical safety of this appliance can only be

guaranteed if the latter is correctly and efficiently

earthed, in compliance with regulations on electrical

safety. Always ensure that this vital safety measure

has been taken. If you have any doubts, call in a

qualified technician to check the electrical system

thoroughly.

•

The manufacturer denies all responsibility for dam-

age resulting from a system which has not been

earthed correctly.

• Before powering the appliance, check whether the

technical characteristics featured on the appliance

data plate correspond with those of the mains elec-

trical system.

• Check that the current load of the mains supply and

of the power sockets is suitable for the maximum

power of the appliance, indicated on the appliance

data plate. If in doubt, contact a qualified professional.

Disconnect the appliance from the electricity supply

before all operations.

Connect your hob to the electrical system by means of

a junction box: if the appliance is connected perma-

nently to the mains, an omnipolar circuit breaker, ac-

cessible if necessary, with a minimum contact opening

of 3 mm should be installed.

Single-phase connection

The hob is equipped with a preconnected electricity supply

cable, which is designed for single-phase connection.

Connect the wires according to the instructions given in

the following table and diagrams:

Voltage and

mains frequency

Electrical cable Wire connection

230V 1+N ~

50 Hz

: yellow/green;

N: the two blue wires

together

L: brown and black

together

Other types of connection

If the mains supply corresponds with one of the follow-

ing:

Voltage and mains frequency

• 400V - 2+N ~ 50 Hz

• 230V 3 ~ 50 Hz

• 400V - 2+2N ~ 50 Hz

Separate the wires and connect them according to the

instructions given in the following table and diagrams:

Voltage and

mains frequency

Electrical cable Wire connection

400V - 2+N ~

50 Hz

230V 3 ~

50Hz

: yellow/green;

N: the two blue wires together

L1: black

L2: brown

400V - 2+2N ~

50 Hz

: yellow/green;

N1: blue

N2: blue

L1: black

L2: brown

If the mains supply corresponds with one of the follow-

ing:

Voltage and mains frequency

• 400V 3 - N ~ 50 Hz

proceed as follows:

! The cable provided is not suitable for the following types

of installation.

1. Use a suitable supply cable, H05RR-F or higher, with

the right dimensions (cable section: 2.5 mm).

2. To open the terminal board, insert a screwdriver into

the side tabs of the cover and open it (

see Terminal

board picture

).

3. Loosen the cable clamp screw and the terminal board

screws according to the type of connection required and

position the connection supports as shown in the follow-

ing table and diagrams.

4. Position the wires according to the following table and

diagrams and connect the appliance by tightening all

the screws for the springs as much as possible.

Voltage and

mains frequency

Electrical connections Terminal board

400V 3-N ~ ı 50

Hz

Three-phase 400

5. Secure the power supply cable by fastening the cable

clamp screw, then put the cover back on.

5

1

2

3

4

U-bolt

connection support

Phase PhasePhase Neutral Earth

Three-phase 400

15

This appliance conforms with the following European

Community Directives:

- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent

amendments;

- 89/336/EEC of 03/05/89 (Electromagnetic

compatibility) and subsequent amendments;

- 93/68/EEC of 22/07/93 and subsequent amendments;

- 2002/96/EC

Warning: If the hob is fitted above a built-in oven, the hob

and the oven must be connected to the mains separately

for safety reasons and to simplify operations when it is

necessary to pull the oven out for some reason.

The European Directive 2002/96/EC on Waste Electrical

and Electronic Equipment (WEEE), requires that old

household electrical appliances must not be disposed

of in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to

optimise the recovery and recycling of the materials they

contain and reduce the impact on human health and the

environment. The crossed out “wheeled bin” symbol on

the product reminds you of your obligation, that when

you dispose of the appliance it must be separately col-

lected.

Consumers should contact their local authority or re-

tailer for information concerning the correct disposal of

their old appliance.

16

Description of cooking zones

Halogen elements

This type of element transmits heat through the radiation of the halogen lamp which it contains. It is held in high

regard because of its properties which are similar to the typical characteristics of gas: rapid response to com-

mands, instant display of power.

The radiant elements

This type of element is made up of many coils which guarantee the uniform distribution of heat on the bottom of the

pot, to ensure perfect cooking on low heat: stews, sauces or dishes that require reheating.

HOBS KBT 6424 DO KBT 8424 DO

Cooking zones

Power

(in W)

Diameter

(in mm)

Power

(in W)

Diameter

(in mm)

Back left

RD 1000/2200 230

Front left

R 1200 140

Back right

R 1200 140 RD 1100/2500 230

Front right

RO 1000/1800 210 R 1200 140

Centre left

RO 1500/2400 210

Centre

R 1800 180

Overall power 6400 7900

H = halogen, R = simple radiant, RO = oval radiant,

RD = dual radiant, RT = triple radiant

Each cooking zone is activated by a power adjustment

device which is made up of a double key (+,-).

The extension of the cooking zones (concentric or oval)

is activated by means of key provided.

As long as the temperature of the cooking zones re-

mains above 60°C, even after they have been switched

off, the residual heat indicators, which are located

near the relative cooking zone, remain on to prevent

you from getting burnt.

The following table provides useful indications on how

to use the various cooking zones in the best way possi-

ble.

Power Type of cooking

1 Melted butter or chocolate

2-3 Heating liquids

4 Preparation of creams and sauces

5 Boiling meats, cooking blanquettes, desserts

6 Cooking pasta and rice

7-8-9 Cooking meats, fish, omelettes

10-11 Frying

17

The controls

6 5 67 71 9 2

4 883 3 3 310

11

5 6 5 6 5

1. On/ off key

2. Control lock key

3. Power indicators

4. Lock indicator light

5. Power increase key

6. Power decrease key

7. Extension key for the extendable cooking zone/s

(concentric or oval): found on hobs where there are 1

or 2 extendable cooking zones

8. Surface operation indicator light for the extendable

cooking zone/s (concentric or oval): found beside each

extendable cooking zone

9. Timer- adjustment key to programme the cooking time

10.Programmed duration indicator

11.Programmed cooking zone indicator light

Note

• The extension key for the extendable cooking zone/s (7) and the relative indicator lights (8) are only found on

models that have extendable cooking zones (concentric or oval).

6 5 67 71 9 2

4 883 3 3 310

11

5 6 5 6 5

18

Operation

When the hob is plugged in, all the indicator lights on

the control panel light up for a few moments and there

will be a short acoustic signal. Subsequently, the con-

trol panel switches off and, at this point, it will be possi-

ble to switch the hob on.

Switching the hob on

To switch on the hob, hold the button down for ap-

proximately 1 second.

Cooking zone operation

Each cooking zone is activated by means of a power

adjustment device which is made up of a double key

(+,-).

Switching on a cooking zone

• To switch on a cooking zone, set the desired power

using the “+” and “-” keys.

• To set the maximum temperature directly, briefly press

the “-” key.

Extendable cooking zone operation

(if the hob comes with extendable cooking zones, see

previous page)

1. Double plate;

a. set the desired power using the “+” and “-”

keys (the innermost cooking zone is activated).

b. if the cooking zone is circular: press to

enable/disable the outermost cooking area

b. if the cooking zone is oval: press to en-

able/disable the extendable cooking area

Switching off a cooking zone

To switch off a cooking zone:

• press thekeys “+” and “-” simultaneously: the power

immediately returns to 0 and the cooking zone

switches off;

• or press the “-” key: the cooking zone’s power de-

creases progressively until it switches off.

Switching off the hob

Press the appliance switches off.

If the hob’s controls have been locked (see previous

paragraph), they will continue to be locked even after

the hob has been switched back on. To switch the hob

back on, it is necessary to unlock the controls.

Locking the controls

When the hob is operating, it is possible to block the

controls to prevent the settings from being accidentally

modified (children, cleaning operations, etc.).

All you have to do is press ; the indicator light above

the key lights up and the controls are locked.

To modify the heating power or to interrupt the cooking

process, it is necessary to unlock the controls: press

for a few moments; the indicator light goes off and

the controls unlock..

Programming the cooking time

It is possible to programme all the cooking zones for a

duration of between 1 and 99 minutes. Proceed as fol-

lows:

•

set the desired power on the plate/s using the “+” and “-

” keys;

• press the programming key until the indicator

light in the position corresponding to the plate that

you intend to programme lights up;

• set the desired cooking time using the “+” and “-”

keys ;

• to confirm the programme

a. press again

b. wait approximately 10 seconds without press-

ing any other keys.

The cooking time countdown begins immediately.

The end of the programmed cooking time is indicated by

means of an acoustic signal (this lasts for 10 seconds)

and the cooking zone switches off.

Repeat the above-mentioned procedure for each plate

that you intend to programme.

19

Programmed time display

If one or more plates have been programmed, the dis-

play shows the time remaining for the plate which is

closest to the end of the programmed time, indicating

its position by means of the corresponding indicator light,

which will be on. The indicator lights that correspond to

the other programmed plates will flash.

To show the time remaining for the other programmed

plates, press repeatedly; the times of all the pro-

grammed plates will be shown in sequence, in an anti-

clockwise direction, beginning from the front left one

(only the corresponding indicator light will be on and the

display flashes)

Modification of programmed times

Proceed as per the paragraph “Programmed time dis-

play” until the time of the plate you intend to modify is

shown. Press the keys “+” and “-” to set the

new time. Confirm by pressing or wait 10 seconds

without pressing any keys.

Cancelling a programme

Display the time of the plate concerned (as in the para-

graph “Programmed time display”) and press the keys

“+” and “-” simultaneously; the programme

is reset and you exit the programming mode.

20

Safety devices

Acoustic signal

Some anomalies, such as:

• an object (pot, utensil, etc.) placed on the control

area for more than 10 seconds,

• a spillage on the control panel,

• sustained pressure on one of the keys, etc.

may cause the acoustic signal to go off.

Remove the cause of the malfunction to stop the acous-

tic signal. The hob remains locked; all you have to do is

unlock it to continues using it (the settings are saved). If

the cause of the malfunction is not eliminated, the acous-

tic signal will carry on, while the hob will switch off for

safety reasons.

Safety switch

The appliance comes with an automatic safety switch

which goes off after a certain time interval (see table) in

accordance with the selected power. During the safety

interruption, the letters “TI” and “ME” alternate on the

display.

for example: the right rear cooking zone is set on 5 and

the front left cooking zone is set on 2. The right rear

zone will switch off after 5 hours of operation, while the

left front zone will switch off after 6 hours of operation.

Power level Operating time limit in hours

110

26

3-4-5 5

64

7-8 3

9-10 2

11 1

Inactivity

If the plate is switched on but is not used for approximately

2 minutes, the control lock function will be enabled. If

the same status remains for approximately another 4

minutes, the plate will switch off automatically.

Overheating

Prolonged use of the hob may cause the electrical com-

ponents to overheat.

A thermal protection device temporarily induces reduced

power (3) on the front cooking zones until the tempera-

ture has come down to an acceptable level.

21

Cleaning and maintenance

Practical tips for the use of the appliance

To get the best performance from your hob, it is essen-

tial follow certain fundamental rules during the cooking

process and when preparing food.

• Use flat-bottomed pans to ensure that they adhere to

the cooking zone perfectly.

• Always use pans with a diameter that is large enough

to cover the hotplate fully, so as to guarantee the use

of all the available heat.

• Make sure that the bottoms of the cookware is al-

ways dry and clean to guarantee correct adherence

and long life, not only for the cooking zones but also

for the cookware itself.

• Avoid using the same cookware that is used on gas

burners. The heat concentration on gas burners may

deform the bottom of the pot; therefore, this will not

allow you to obtain the desired result when used on a

glass ceramic hob.

• Never leave a cooking zone on without cookware on

it because as it heats up and rapidly reaches the

maximum level, it could damage the heating elements.

Always keep the hob clean. Before performing any main-

tenance on the hob, ensure that the heating zones are

off and that they have cooled down.

Stainless steel frame (only on some models)

Stainless steel may stain due to water that is very high

in calcium, if it is left in contact with the steel for pro-

longed periods of time or due to extremely aggressive

cleaning products (which contain phosphorus). We rec-

ommend that you rinse and dry thoroughly after clean-

ing the hob. If water is spilled on the hob, act rapidly and

dry it carefully.

Hob maintenance

The glass ceramic hob used as a heating surface is

perfectly smooth and not porous at all; furthermore, un-

der normal conditions of use, it resistant to heat shock

as well as mechanical shock. In order to ensure correct

preservation of all the hob’s properties, we recommend

that maintenance be carried out as follows:

• for ordinary maintenance, all you have to do is wash

it with a wet sponge, then dry it with kitchen towel

paper.

• If the hob is very dirty, scrub with a product that is

specifically suited to glass ceramic surfaces, rinse

and then dry.

• to remove thicker residuals, use a scraper. Act as

soon as possible, without waiting for the appliance to

cool down to prevent the residual from forming a crust.

You can obtain excellent results by using a stainless

steel wool sponge - which is specifically suited to

glass ceramic hobs- and which has been soaked in

water and soap.

• Once it has been cleaned, the hob may be treated

with a specific product for maintenance and protec-

tion: the invisible film left behind by this product pro-

tects the surface in case there are any leaks during

the cooking process. Remember to carry out these

operations when the appliance is lukewarm or cold.

• Also remember to always rinse with clean water and

to dry the hob thoroughly: product residuals could

form crusts the next time you cook.

Important tips

• Avoid using abrasive or corrosive detergents, such

as products in spray cans for barbecues and ovens,

stain-removers and anti-rust products, detergents in

powder form and sponges with abrasive surfaces, be-

cause these can all scratch the surface causing last-

ing damage.

• Remember to keep any object that could melt away

from the hob, for example plastic objects, sugar and

products with a high sugar content. If any of these

products are spilled on the hob, remove them imme-

diately (while the surface is still hot) with a razor-

blade scraper so as not to damage the surface.

• The hob must only be used for cooking. Do not

place any objects on the hob when it is not being

used. Do not use the hob as a resting surface (for

cutlery, cookware, scrubs, etc.) or as a cutting sur-

face.

• Aluminium packaging, aluminium film and plastic con-

tainers must never be left on the surfaces that are

still lukewarm or hot.

• Do not use steam or high-pressure cleaners to clean

the appliance.

Page is loading ...

Whirlpool KBT 6424 DO IX User guide

This manual is also suitable for

Whirlpool KBT 6424 DO IX User guide

in other languages

Related papers

Other documents