Hoshizaki F-330BAJ User manual

Models

F-330BAJ(-C)

Self-Contained Flaker

Service Manual

Number: 73211

Issued: 2-17-2017

hoshizakiamerica.com

WARNING

Only qualied service technicians should install and service the appliance. To

obtain the name and phone number of your local Hoshizaki Certied Service

Representative, visit www.hoshizaki.com. No service should be undertaken until

the technician has thoroughly read this Service Manual. Failure to service and

maintain the appliance in accordance with this manual will adversely affect safety,

performance, component life, and warranty coverage and may result in costly water

damage. Proper installation is the responsibility of the installer. Product failure or

property damage due to improper installation is not covered under warranty.

Hoshizaki provides this manual primarily to assist qualied service technicians in the

service of the appliance.

Should the reader have any questions or concerns which have not been satisfactorily

addressed, please call, send an e-mail message, or write to the Hoshizaki Technical

Support Department for assistance.

Phone: 1-800-233-1940; (770) 487-2331

Fax: 1-800-843-1056; (770) 487-3360

E-mail: techsuppor[email protected]

618 Highway 74 South

Peachtree City, GA 30269

Attn: Hoshizaki Technical Support Department

Web Site: www.hoshizaki.com

NOTE: To expedite assistance, all correspondence/communication MUST include the

following information:

• Model Number

• Serial Number

• Complete and detailed explanation of the problem.

CONTENTS

Important Safety Information ................................................................................................. 5

I. Construction and Water/Refrigeration Circuit Diagram ....................................................... 7

A. Construction .................................................................................................................. 7

B. Icemaking Unit .............................................................................................................. 8

C. Water/Refrigeration Circuit Diagram .............................................................................. 9

II. Sequence of Operation and Service Diagnosis ............................................................... 10

A. Sequence of Operation Flow Chart ............................................................................. 10

1. Icemaking and Drain Cycle .................................................................................... 10

2. Shutdown ...............................................................................................................11

B. Service Diagnosis ....................................................................................................... 12

1. Ice Production Check ............................................................................................. 12

2. Diagnostic Procedure............................................................................................. 13

C. Control Board Check ................................................................................................... 18

D. Bin Control Check ....................................................................................................... 22

E. Float Switch Check and Cleaning ............................................................................... 24

F. Diagnostic Tables ......................................................................................................... 26

III. Controls and Adjustments ............................................................................................... 28

A. Control Board .............................................................................................................. 28

1. Control Board Layout Shown: ................................................................................. 29

2. LED Lights and Audible Alarm Safeties ................................................................. 30

3. Ice Purge Cycle Bypass ......................................................................................... 31

B. Controls and Adjustments ........................................................................................... 31

1. Default Dip Switch Settings .................................................................................... 31

2. Infrared Sensor Shutdown Delay (S1 dip switch 1, 2, 3) ....................................... 32

3. Drain Frequency Control (S1 dip switch 4) ............................................................ 32

4. Continuous Dispensing Timer (S1 dip switch 5 & 6) ............................................. 32

5. Bin Control Selector (S1 dip switch 7) ................................................................... 33

6a. Mechanical Shutdown Delay (S1 dip switch 8) Auxiliary Code E-0: .................... 33

6b. Agitation and Ice Purge Timer (S1 dip switch 8) Auxiliary Code F-0 and Later: ... 33

7. Mechanical Shutdown Delay (S1 dip switch 9) Auxiliary Code F-0 and Later ........ 34

8a. Factory Use (S1 Dip Switch 9 & 10) Auxiliary Code E-0 ...................................... 34

8b. Factory Use (S1 Dip Switch 10) Auxiliary Code F-0 and Later ............................. 34

C. Power Switch and Control Switch ................................................................................ 35

IMPORTANT

This manual should be read carefully before the appliance is serviced. Read

the warnings and guidelines contained in this manual carefully as they provide

essential information for the continued safe use, service, and maintenance of the

appliance. Retain this manual for any further reference that may be necessary.

IV. Refrigeration Circuit and Component Service Information.............................................. 36

A. Refrigeration Circuit Service Information .................................................................... 36

B. Component Service Information .................................................................................. 39

V. Maintenance .................................................................................................................... 47

VI. Disposal .......................................................................................................................... 49

VII. Technical Information ..................................................................................................... 50

A. Specication & Performance Data Sheets .................................................................. 50

1. F-330BAJ ............................................................................................................... 50

2. F-330BAJ-C ........................................................................................................... 51

B. Wiring Diagram ............................................................................................................ 52

Important Safety Information

Throughout this manual, notices appear to bring your attention to situations which could

result in death, serious injury, damage to the appliance, or damage to property.

WARNING Indicates a hazardous situation which could result in death or

serious injury.

NOTICE Indicates a situation which could result in damage to the

appliance or property.

IMPORTANT Indicates important information about the use and care of the

appliance.

WARNING

The appliance should be destined only to the use for which it has been expressly

conceived. Any other use should be considered improper and therefore dangerous.

The manufacturer cannot be held responsible for injury or damage resulting from

improper, incorrect, and unreasonable use. Failure to install, operate, service and

maintain the appliance in accordance with this manual will adversely affect safety,

performance, component life, and warranty coverage and may result in costly water

damage.

To reduce the risk of death, electric shock, serious injury, or re, follow basic

precautions including the following:

• Only qualied service technicians should install and service the appliance.

• The appliance must be installed in accordance with applicable national, state, and

local codes and regulations. Failure to meet these code requirements could result in

death, electric shock, serious injury, re, or damage to the appliance.

• To reduce the risk of electric shock, do not touch the appliance power switch or plug

with damp hands.

• Make sure the appliance power switch is in the "OFF" position before plugging in or

unplugging the appliance.

• Before servicing, move the power switch to the "OFF" position. Unplug the

appliance from the electrical outlet.

• The appliance requires an independent power supply of proper capacity. See the

nameplate for electrical specications. Failure to use an independent power supply

of proper capacity can result in a tripped breaker, blown fuse, damage to existing

wiring, or component failure. This could lead to heat generation or re.

• THE APPLIANCE MUST BE GROUNDED. The appliance is equipped with a

NEMA5-15 three-prong grounding plug to reduce the risk of potential shock

hazards. It must be plugged into a properly grounded, independent 3-prong wall

outlet. If the outlet is a 2-prong outlet, it is your personal responsibility to have

a qualied electrician replace it with a properly grounded, independent 3-prong

wall outlet. Do not remove the ground prong from the power cord and do not use

an adapter plug. Failure to properly ground the appliance could result in death or

serious injury.

• Do not make any alterations to the appliance. Alterations could result in electric

shock, injury, re, or damage to the appliance.

WARNING, continued

• Do not use an extension cord.

• Do not use an appliance with a damaged power cord. The power cord should not

be altered, jerked, bundled, weighed down, pinched, or tangled. Such actions could

result in electric shock or re. To unplug the appliance, be sure to pull the plug, not

the cord, and do not jerk the cord.

• The GREEN ground wire in the factory-installed power cord is connected to the

appliance. If it becomes necessary to remove or replace the power cord, be sure to

connect the power cord's ground wire.

• Do not place ngers or any other objects into the ice discharge opening.

• The appliance is not intended for use by persons (including children) with reduced

physical, sensory, or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use of the

appliance by a person responsible for their safety.

• Children should be properly supervised around this appliance.

• Do not climb, stand, or hang on the appliance or allow children or animals to do so.

Serious injury could occur or the appliance could be damaged.

• Do not use combustible spray or place volatile or ammable substances near the

appliance. They might catch re.

• Keep the area around the appliance clean. Dirt, dust, or insects in the appliance

could cause harm to individuals or damage to the appliance.

NOTICE

• Follow the instructions in this manual carefully to reduce the risk of costly water

damage.

• In areas where water damage is a concern, install in a contained area with a oor

drain.

• Install the appliance in a location that stays above freezing. Normal operating

ambient temperature must be within 45°F to 100°F (7°C to 38°C).

• Do not leave the appliance on during extended periods of non-use, extended

absences, or in sub-freezing temperatures.

• Do not place objects on top of the appliance.

• The ice storage bin is for ice use only. Do not store anything else in the ice storage

bin.

I. Construction and Water/Refrigeration Circuit Diagram

A. Construction

1. F-330BAJ(-C)

Ice Storage Bin

Inlet Water Valve

Reservoir

Control Box

Bin Control

The switch actuator

is located in the ice

storage bin.

Spout

Evaporator

Gear Motor

Compressor

Front

Rear

Drain Valve

Spout Safety Switch

Evaporator Heater

(-C Model)

B. Icemaking Unit

1. F-330BAJ(-C)

Evaporator Heater (-C Model)

Seal Bolt

Gear Motor

Spline Coupling

Housing-Lower Bearing

O-Ring

Mechanical-Seal

Cylinder

Auger

Extruding Head Upper Bearing

Cutter

Insulation

Socket Head Cap Screw

and Split Lock Washer

Hex Bolt and Washer

C. Water/Refrigeration Circuit Diagram

Drier

Condenser

Fan Motor

High Pressure

Switch

Compressor

Overow

Hose

Reservoir

Drain

Valve

Thermostatic

Expansion Valve

Spout

Water Level

Evaporator

Float

Switch

Inlet Water Valve

Water Supply

Line

Gear Motor Drain Pan

Bin Drain

Hose

Insulation

Evaporator Condensate

Drain Pan (Drip Pan)

Gear Motor

Dip Tube Drain Hose

Drain Outlet

II. Sequence of Operation and Service Diagnosis

A. Sequence of Operation Flow Chart

1. Icemaking and Drain Cycle

F-330BAJ(-C) Sequence Flow Chart

1-in-1 drain cycle. DV opens for 2 sec. every hour

(CB S1 Dip Switch 4).

Icemaker status does not change.

LFS closed

UFS closed

FZT starts

FT terminated

WV de-energized

3. 1-in-12 Drain Cycle

& Restart (optional)

UFS open

LFS open (WV on)

FT starts (90 sec.)

FZT terminated

WV energized

Comp continues

GM continues

FM continues

1. Startup

2. Ice Purge Cycle

WV energized

Comp energized

GM continues

FM continues

2. 1-in-1 Drain Cycle

Comp de-energized

GM continues

FM continues

1. Fill Cycle

3. Freeze Cycle

LFS closed

UFS closed

FZT starts (30 min.)

FT terminated

WV de-energized

Comp continues

GM continues

FM continues

Low Water Safety

Purge Timer

UFS open

WV energized

Comp de-energized

GM continues

FM continues

DV energized

GM de-energized

FM de-energized

10-min. DT terminated

DV de-energized

1-in-12 DT reset

5 min.

4. Icemaker Restart

2. Ice Purge Cycle

3. 10-Min. Drain

If Fill > 90 sec. FT

1-beep alarm sounds

WV continues

When UFS closes

alarm resets and

2. Ice Purge Cycle starts.

FT Maximum

90 sec.

4. 1-in-12 Drain Cycle - Although the factory default 1-in-1 drain cycle

is recommended, a 1-in-12 drain cycle is available. For 1-in-12 drain

cycle sequence, see "3. 1-in-12 Hour Drain Cycle & Restart (optional)."

Rell

FT Maximum

90 sec.

90 sec. FT exceeded,

90 sec. PT starts and

1-beep alarm sounds

90. sec. PT terminates

unit shuts down and

1-beep alarm continues.

When UFS closes, alarm

resets and 2. Ice Purge

Cycle starts.

WV continues

GM de-energized

FM de-energized

1. DT Initiates DC

To bypass, press the

"SERVICE" button after

GM starts.

5 min.

to "1. Fill Cycle" above

90 sec.

(CB S1 dip switch 4 "ON")

FT off (90 sec.)

5 or 30 sec.

(S1 Dip Switch 7)

EH energized

GM energized

FM energized

1. DT Initiates DC

Continued uninterrupted

operation

DV energizes for 2 sec.

2. Continued Operation

DV de-energizes, no

interruption in ice production

30-min. FZT

Startup

FZT exceeded (LFS does not

open): CB shuts down icemaker

and sounds a 5-beep alarm.

Legend:

BC-bin control

CB-control board

Comp-compressor

DC-drain cycle

DT-drain timer

DV-drain valve

EH-evaporator heater

FM-fan motor

FT-ll timer (low water safety)

FZT-freeze timer

GM-gear motor

LFS-lower oat switch

PT-purge timer

UFS-upper oat switch

WV-inlet water valve

Low Water Safety

Shutdown

(CB S1 dip switch 4 "OFF")

Normal Operation

Power Switch "ON"

Control Switch in "ICE"

POWER OK LED on

BC Closed

Control Board Sequence of Operation Flow Chart - Shutdown

1. Bin Full

6 to 10 sec.

All Components

de-energized

BC closed

(BC actuator paddle and

proximity switch disengaged)

to "2. Ice Purge Cycle" in Icemaking

and Drain Cycle Chart

BC open

BC actuator

paddle and

proximity switch

engaged

2. Icemaker Off 3. Icemaker Restart

Ice level lowered

4a. Bin Control

Shutdown & Restart

Auxiliary Code: E-0

Legend:

BC-bin control

CB-control board

Comp-compressor

FM-fan motor

GM-gear motor

2. Shutdown

Legend:

BC-bin control

Comp-compressor

DC-drain cycle

DT-drain timer

DV-drain valve

FM-fan motor

FT-ll timer (low water safety)

GM-gear motor

LFS-lower oat switch

PT-purge timer

UFS-upper oat switch

WV-inlet water valve

to "2. Ice Purge Cycle" above if UFS closed.

to "1. Fill Cycle" above if UFS open.

1. Bin Full

GM energized

Comp de-energized

FM de-energized

GM de-energized

3. Icemaker Off

BC open

Comp energized

FM energized

GM energized

2. Ice Purge Cycle

4. Icemaker

Restart

150-sec. Shutdown Sequence

BC closed

4b. Bin Control

Shutdown & Restart

Auxiliary Code F-0 and Later

BC open

(BC actuator

paddle engaged)

90 sec. 60 sec.

B. Service Diagnosis

WARNING

• The appliance should be diagnosed and repaired only by qualied service

personnel to reduce the risk of death, electric shock, serious injury, or re.

• Risk of electric shock. Use extreme caution and exercise safe electrical practices.

• Moving parts (e.g., fan blade or auger) can crush and cut. Keep hands clear.

• CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are

securely in place after the appliance is serviced. Make sure that none have fallen

into the ice storage bin.

• Make sure all food zones in the icemaker and ice storage bin are clean after

service.

1. Ice Production Check

To check production, prepare a bucket or pan to catch the ice and a set of scales to

weigh the ice. After the appliance has operated for 10 to 20 minutes, catch the ice

production for 10 minutes. Weigh the ice to establish the batch weight. Multiply the

batch weight by 144 for the total production in 24 hours. When conrming production or

diagnosing low production, reference production information to the performance data

charts found in "VII.A. Specication and Performance Data Sheets."

2. Diagnostic Procedure

This diagnostic procedure is a sequence check that allows you to diagnose the electrical

system and components. Before proceeding, check for correct installation, proper voltage

per appliance nameplate, and adequate water pressure (10 PSIG to 113 PSIG).

Note: • When checking high voltage (115VAC), always choose a neutral (W) wire to

establish a good neutral connection.

• When checking low voltage (24VAC), always choose a neutral (LBU) wire to

establish a good neutral connection.

• When checking control board DC voltage (5VDC), always place the red positive

test lead from the multimeter to CB K5 pin closest to CB K4 connector.

See "II.C. Control Board Check."

• To speed up the diagnostic process, the 5-min. ice purge cycle may be bypassed

by pressing the "SERVICE" button on the control board after the gear motor

starts. WARNING! Risk of electric shock. Care should be taken not to touch

live terminals.

• If the icemaker is in alarm, see "III.A.2. LED Lights and Audible Alarm Safeties."

• FM and EH (-C model) energize when "GM" LED turns on.

• CB monitors the following switches with 5VDC during the icemaking process:

Control Switch (CS), High-Pressure Switch (HPS), Float Switch (FS),

Compressor Control Relay/Gear Motor Protect Relay (CCR/GMPR), and Bin

Control (mechanical stand-alone). When 5VDC is present across any of these

switches, the switch is open.

1) Remove the front panel, then move the power switch to the "OFF" position. Move the

control switch to the "DRAIN" position, then move the power switch back to the "ON"

position. Replace the front panel in its correct position.

2) Allow the water system to drain for 5 min.

3) Remove the front panel. Move the power switch to the "OFF" position, then turn off the

power supply.

4) Remove the control box cover and access CB.

5) Check the CB S1 dip switch settings, see "III.B.1. Default Dip Switch Settings" to

assure that they are in the correct positions. For proper operation of BC (mechanical

stand-alone), conrm that S1 dip switch 7 is in the "OFF" position.

6) Startup–CB "POWER OK" LED is on. Turn on the power supply, then move the power

switch to the "ON" position. Make sure the control switch is in the "ICE" position.

CB "POWER OK" LED turns on.

Diagnosis CB "POWER OK" LED: Check that CB "POWER OK" LED is on. Ifnot,

check for 115VAC at control transformer black (BK) wire to neutral (W). If 115VAC is not

present, check the power switch, power supply cord, and breaker. If 115VAC is present,

check control transformer continuity. Replace as needed. Next, check for 24VAC at

control transformer red (R) wire to neutral (LBU). If 24VAC is not present, check control

transformer continuity. Replace as needed. If24VAC is present, check 24VAC 3A fuse.

If fuse is good, check for 24VAC at CB K8 #1 (W/R) to CB K8 #2 (LBU). If 24VAC is

present and "POWER OK" LED is off, replace CB.

Diagnosis BC (mechanical stand-alone): Check that the actuator paddle is properly

positioned. Check continuity across BC. If open, replace BC. Next, check VDC at CB

K8#3(GY) to CB K8 #4 (GY). When BC is closed 0VDC is read. Move the actuator

paddle to open BC(2). When open, 5VDCis present between CB K8 #3 (GY) and CB

K8#4(GY). If 5VDC is not present when BC is open, replace CB. Return actuator to its

normal position.

7) Fill Cycle – "WTRIN" LED is on. Reservoir is empty and LFS and UFS are open.

90-sec. FT starts. WV energizes and ll cycle starts. LFS closes. Nothing occurs at this

time. Reservoir continues to ll until UFS closes. When UFS closes, WV de-energizes,

90-sec. FT is terminated, and CB "WTRIN" LED turns off. 30-min. FZTand 5-sec.

GM delay timer start. IfUFS remains open longer than 90 sec. after LFS opens,

FTexceeded and CB sounds a 1-beep alarm. WVremains energized until UFS closes.

Alarm resets automatically when UFS closes. Diagnosis: If reservoir is empty and

"WTRIN" LED is off, conrm LFS status. See "II.E. Float Switch Check and Cleaning."

IfLFS is open and "WTRIN" LED is off, replace CB. If "WTRIN" LED is on, check

that the reservoir lls. If not, check water supply line shut-off valve, water lters, and

WVscreen. If "WTRIN" LED is on and WV is off, check CB K2 #8(O) to a neutral

(LBU) for 24VAC. If24VAC is not present, check CB K2 #9(W/R) to a neutral (LBU) for

24VAC. If 24VAC is present on CB K2 #9(W/R)and not on CB K2 #8 (O), replace CB.

If 24VAC is present on CB K2 #8(O), check continuity through WV solenoid. If open,

replace WV. If WV is energized and rell exceeds FT with no water in the reservoir,

check for DV leaking. Ifreservoir is full and overowing check for open UFS. See "II.E

Float Switch Check and Cleaning." If UFS is closed, check that WV de-energizes. If

not, check CB K2 #8 (O) to a neutral (LBU) for 24VAC. If 24VAC is present, replace CB.

IfWV de-energizes and water continues to ll the reservoir, replace WV.

8) Ice Purge Cycle – "GM" LED is on. 5-sec. GM delay timer terminates. GM,

CCR, FM, and EH (-C model) energize. Once CCR energizes, 5VDC circuit closes

through CCR terminal #3 (W/O) and terminal #5 (W/O) and CB K9 #5 (W/O) and

K9 #6 (W/O). After 5VDC circuit closes, 5-min. ice purge timer starts. Tobypass the

5-min. Ice Purge Cycle, press the "SERVICE" button on CB after the "GM" LED turns

on. WARNING! Risk of electric shock. Care should be taken not to touch live

terminals. Diagnosis: If "GM" LED is off, check that UFS closes and WV de-energizes.

IfUFS is closed, 30 sec. has passed, and "GM" LED remains off, replace CB. If"GM"

LED is on and GM is off, check CB K1 #2 (BK) to a neutral (W) for 115VAC. If115VAC is

not present, check 115VAC power supply. If115VAC is present, check CB K1 #3(P) to

a neutral (W). If 115VAC is present on CB K1 #2 (BK) and not on CB K1 #3 (P), replace

CB. If115VAC is present on CB K1#3 (P), check GM fuse, GM internal protector,

GM windings and capacitor, and GM coupling between auger and GM. When GM

energizes, CCR energizes starting 5-min. ice purge timer. If FM does not start, check

FM capacitor, FM windings, and FM bearings.

9) Freeze Cycle – "COMP" and "GM" LEDs are on. The 5-min. ice purge timer

terminates. GM, EH (-C model), CCR, and FM continue. Comp energizes. Ice

production starts 4to 6 min. after Comp energizes depending on ambient and water

conditions. As ice is produced, the water level in the reservoir drops. UFS opens.

Nothing happens at this time. When LFS opens, WV energizes and rell cycle begins,

FZT terminates, and FTstarts.

FZT: 30-Min. Freeze Safety Timer – FZT starts when UFS closes and terminates

when LFS opens. If LFS does not open within 30 min. of UFS closing, CB shuts down

the icemaker and sounds a 5-beep alarm. See "III.A.2.LED Lights and Audible Alarm

Safeties." To reset, turn the power supply off and on again. See "II.F. Diagnostic Tables"

for troubleshooting details.

Icemaker Diagnosis (CCR): 5-min. ice purge timer terminates, CB "COMP" LED is on

and COMP energizes. If not, check for 5VDC between CB K5 connector pin closest

to CB K4 connector and CB K9connector #5(W/O). If 5VDC is not present, replace

CB. If 5VDC is present, check for 5VDC between CB K5 connector pin closest to CB

K4 connector and CB K9connector #6(W/O). If 5VDC is present and CB "Comp"

LED is off (CR or COMP not energized), replace CB. If 5VDC is not present, check for

115VAC between CCR terminal #7(O) to CCR terminal #8(W) for 115VAC. If115VAC

is not present (GM not energized), see step 8 above. If 115VAC is present and CCR

contacts are open (5VDCpresent between terminals #3(W/O) and #5(W/O)), check

CCR solenoid voltage and solenoid continuity. Replace CCR if necessary.

Icemaker Diagnosis (COMP): If"COMP" LED is on and COMP is not energized,

check CB X1 relay BK wire to a neutral (W) and CB X1 relay V wire to a neutral (W) for

115VAC. If115VAC is present on CB X1BK wire and not on CBX1 V wire, replace CB.

If115VAC is present on CBX1V wire and COMP is not energized, check for 115VAC

at CB X1 Comp relay. Check Comp internal overload (motor protector), start relay, and

capacitors.

10) Rell Cycle – "GM", "COMP", and "WTRIN" LEDs are on.

LFS opens. WVenergizes and 90-sec. FT starts. Comp, GM, CCR, and FM continue.

LFS closes. Nothing occurs at this time. Reservoir continues to ll until UFS closes.

When UFS closes, WV de-energizes, 90-sec. FT terminates, and 30-min. FZT starts.

IfUFS remains open longer than 90 sec. after LFS opens, FT exceeded and CB sounds

a 1-beep alarm. WVremains energized until UFS closes. Alarm resets automatically

when UFS closes.

Diagnosis – Conrm that the water level has dropped and the UFS and LFS are open.

See "II.E. Float Switch Check and Cleaning." Check that "WTRIN" LED is on. IfLFS

is open and "WTRIN" LED is off, replace CB. If "WTRIN" LED is on, check that the

reservoir lls. Ifnot, check water supply line shut-off valve, water lters, and WVscreen.

If"WTRIN" LED is on and WV is off, check CB K2 #8(O) to a neutral (LBU) for 24VAC.

If 24VAC is not present, check CB K2 #9(W/R) to a neutral (LBU) for 24VAC. If 24VAC

is present on CB K2 #9 (W/R)and not on CB K2#8 (O), replace CB. If 24VAC is

present on CB K2#8(O),check continuity through WV solenoid. If open, replace WV.

IfWV is energized and rell exceeds FT with no water in the reservoir, check for DV

leaking. Ifreservoir is full and overowing check for open UFS. See "II.E. Float Switch

Check and Cleaning." If UFS is closed, check that WVdeenergizes. If not, check

CB K2 #8(O) to a neutral (LBU) for 24VAC. If 24VAC is present, replace CB. If WV

de-energizes and water continues to ll the reservoir, replace WV.

Note: Each time UFS closes, 30-min. freeze timer starts. The 30-min. freeze timer

resets when UFS closes again. If UFS does not close again within 30 min., CB

shuts down the unit and sounds a 5-beep alarm every 5 sec.

See "III.A.2 LED Lights and Audible Alarm Safeties."

FT: 90-Sec. Low Water Safety Timer – When LFS opens, 90-sec. low water safety

timer starts. If UFS does not close within 90 sec. after LFS opens (FTexceeded),

CBsounds a 1-beep alarm and a 90-sec. shutdown cycle starts

See "III.A.2.LED Lights and Audible Alarm Safeties." Comp de-energizes. GM, CCR,

and EH (-C model) continue. 90-sec. purge timer terminates, GM, EH (-C model), and

CCR de-energize. WV and 1-beep alarm continue until UFS closes.

11) Drain Cycle

a) 1-in-1 Drain Cycle: DV energizes once every hour when the 1-in-1 drain cycle is

activated (S1 dip switch 4 in the "OFF" position (factory default position)). GM,

FM, Comp continue. DV energizes for 2 sec. every hour. This setting is

recommended for optimum icemaker performance. The 1-in-1 drain cycle allows any

sediment to drain from the evaporator without interrupting the icemaking process.

b) 1-in-12 Drain Cycle (optional): DV energizes once every 12 hours when the 1-in-12

drain cycle is activated (S1 dip switch 4 in the on position (optional)). 12-hour drain

cycle timer terminates, Comp de-energizes. GM, and FM continue. The 5-min.

ice purge timer starts. When the 5-min. ice purge timer terminates, GM and FM

de-energize. 10-min. DT starts, DV energizes. After 10-min. DT terminates, DV

de-energizes icemaking process restarts and 12-hour drain cycle timer starts.

c) Manual Drain: Manual drain is used when servicing evaporator components and

cleaning and sanitizing the unit. When the unit is making ice and the control switch

is moved to the "DRAIN" position, there is a 3-sec. delay, then Comp de-energizes

and the 5-min. ice purge timer begins. When the 5-min. ice purge timer terminates,

GM and FM de-energize. DV energizes to drain the evaporator and reservoir.

Toavoid the 5-min. shutdown delay, turn off the power supply, then move the control

switch to the "DRAIN" position. Turn on the power supply. DV energizes to drain the

evaporator and reservoir. DV de-energizes when the control switch is moved to the

"ICE" position.

10) Shutdown

a) Auxiliary Code: E-0: Bin lls with ice activating BC proximity switch. BC opens

(actuator paddle engaged). CB shuts down the icemaker within 10 sec.

Auxiliary Code: F-0 and Later: Bin lls with ice activating BC proximity switch.

CB starts 90-sec. Comp shutdown timer. Once 90-sec. Comp shutdown timer

terminates, Comp and FM de-energize and 60-sec. GM shutdown timer starts. Once

60-sec. GM shutdown timer terminates, GM de-energizes and icemaker is off.

Shutdown Diagnosis: Check that BC actuatour paddle is activated and not sticking.

Check BC proximity switch continuity. When BC actuator paddle is down (icemaking),

BC proximity switch is closed. When BC actuator paddle is up BC proximity switch is

open. If not, replace BC proximity switch. If BC proximity switch is open and Comp, FM,

and GM do not de-energize, replace CB. See "II.C. Control Board Check Procedure."

Note: Dip Switch 9 becomes active with aux. code F-0 and later. This allows for

management between fast shutdown and slow shutdown. Default setting for F-0 and

later is for slow shutdown Dip Switch 9 "OFF" position. Dip switch 9 can be moved to

the "ON" position for fast-timing (shutdown within 6 to 10 sec.).

Legend: BC–bin control; CB–control board; CCR–compressor control relay;

Comp–compressor; DV–drain valve; EH–evaporator heater (-Cmodel);

FM–fan motor; GM–gear motor; GMR–gear motor relay; LFS–lower oat switch;

UFS–upper oat switch; WV–inlet water valve

C. Control Board Check

Before replacing a control board that does not show a visible defect and that you suspect

is bad, always conduct the following check procedure. This procedure will help you verify

your diagnosis.

1) Check CB S1 dip switch settings to assure that they are in the factory default position.

For factory default settings, see "III.B.1. Default Dip Switch Settings."

Note: S1 dip switch 7determines bin control application:

BC: S1 dip switch 7 in the "OFF" position.

2) Move the power switch to the "ON" position and move the control switch to the "ICE"

position. The "POWER OK" LED turns on. Diagnosis "POWER OK" LED: Check that

the CB "POWER OK" LED is on. If not, check for proper supply voltage (115VAC) input

to the control transformer (power switch, power supply cord, breaker, and fuse). Next,

check for proper low-voltage (24VAC) output from the control transformer and that the

3A fuse is good. Check for 24VAC at CB K8 #1 (W/R) to CB K8 #2 (LBU). If 24VAC is

present and the "POWER OK" LED is off, replace CB.

3) 5VDC Output Checks:

CB K9 Connector: Control Switch (CB K9 #1 and #2) (open contacts for icemaking,

closed contacts for drain), High-Pressure Switch (CB K9 #3 and #4), Compressor

Control Relay (K9 #5 and #6).

CB K8 Connector: Bin Control (K8 #3 and #4) and Float Switch (K8 #5 (common),

#6(lower), and #7 (upper)).

When checking 5VDC control voltage, always place the red positive test lead from

the multimeter to the CB white K5 pin closest to the CB red K4 connector. See Fig. 1.

Then place the black negative test lead from the multimeter to the corresponding pin to

complete the 5VDC check.

Red positive test lead

to K5 pin closest to K4

connector

Fig. 1

Control Board K9 Connector

Red Positive

Test Lead

Black Negative

Test Lead

Multimeter

5VDC

Control Switch

white/black (W/BK)

High-Pressure Switch

yellow (Y) wires

Compressor Control Relay/

Gear Motor Protect Relay

(terminals #3 and #5)

white/orange (W/O)

a) Control Switch – CB K9 #1 (W/BK) and CB K9 #2 (W/BK): 5VDC is present

between CB white K5 connector, pin closest to CB red K4 connector and CB K9

#1(W/BK) at all times. If 5VDC is not present, replace CB. When the control switch is

in the "ICE" position, the control switch contacts are open. 0VDC is present between

CB white K5 connector, pin closest to CB red K4 connector and CB K9 #2 (W/BK).

When in the "ICE" position, 5VDC is present between CB K9 #1 (W/BK) to CB K9

#2 (W/BK). When the control switch is in the "DRAIN" position, the control switch

contacts are closed. 5VDC is present between CB white K5 connector, pin closest

to CB red K4 connector, to CB K9 #1 (W/BK) or#2(W/BK). If 5VDC is not present,

replace CB. 0VDC is present from CB K9 #1(W/BK) to CB K9 #2 (W/BK).

b) High-Pressure Switch – CB K9 #3 (Y) and CB K9 #4 (Y): 5VDC is present between

CB K5 connector, pin closest to CB red K4 connector and CB K9 #3 (Y) at all times.

When the high-pressure switch is closed, 5VDC is present between CB K5 pin

closest to CB K4 connector to CB K9 #3 (Y) and CB K9 #4 (Y). If 5VDC is not

present, replace CB. When the high-pressure switch is closed, 0VDC is present at

CB K9 #3 (Y) to CB K9 #4 (Y). When the high-pressure switch is open, 5VDC is

present at CB K9 #3 (Y) to CB K9 #4 (Y). If the high-pressure switch is open and

CB is not in alarm, replace CB. If5VDC is present at CB K9 #3 (Y) and not at CB

K9 #4 (Y), the high-pressure switch is open and CB sounds a 3-beep alarm. Check

continuity across the high-pressure switch (CB K9 #3 (Y) and CB K9 #4 (Y)).

c) Compressor Control Relay (CCR) – CB K9 #5(W/O) and CB K9 #6 (W/O):

5VDC is present from CB white K5 connector, pin closest to CB red K4 connector

to CB K9 #5 (W/O) at all times. If 5VDC is not present, replace CB. When CCR

terminals #3 (W/O) and #4 (W/O) are open (CCR de-energized), 5VDC is present

between CB K9 #5 (W/O) and CB K9 #6 (W/O). When CCR terminals #3(W/O) and

#4 (W/O) are closed (CCR energized), 5VDC is present between CB K9 #5 (W/O)

and CB K9 #6 (W/O). When CCR terminals #3(W/O) & #5 (W/O) are open CB may

be in an 8-beep alarm. See "III.A.2. LED Lights and Audible Alarm Safeties."

d) Bin Control – CB K8 #3 (GY) and CB K8 #4(GY): 5VDC is present from CB white

K5 connector, pin closest to CB red K4 connector to CB K8 #3 (GY) at all times.

If 5VDC is not present, replace CB. When BC is closed (calling for ice), 5VDC is

present from CB white K5 connector, pin closest to CB red K4 connector, to CB K8

#3 (GY) and CB K8 #4(GY). If 5VDC is not present to either CB K8 #3 (GY) or CB

K8 #4(GY), replace CB. If 5VDC is present at CB K8 #3 (GY) and not to CB K8 #4

(GY), BC is open. See "II.D. Bin Control Check."

e) Float Switch (LFS and UFS) – CB K8 #5 (BK) (common), CB K8 #6(R) (upper),

and CB K8 #7 (BU) (lower): 5VDC is present from CB white K5 connector pin closest

to CB red K4 connector to CB K8 #5(BK) (common) at all times. If not, replace CB.

5VDC is present from CB white K5 connector pin closest to CB red K4connector

to CB K8 #6 (R) (upper) and CB K8 #7 (BU) (lower) when FS is open. If 5VDC

is present between CB K8 #5 (BK) and CB K8 #6 (R) (upper) or CB K8 #7 (BU)

(lower), FS is open. Forfurther FS diagnostics, see "II.E. Float Switch Check and

Cleaning."

5) Fill "WTRIN" LED is on: 24VAC is present at CB K2 #9 (W/R) at all times. If not,

conrm 24VAC from CB K2 #9(W/R) to a neutral (LBU). When LFS open at startup

or opens during normal operation, "WTRIN" LED turns on, ll timer (FT) starts, freeze

timer (FZT) terminates (only during normal operation), and WV energizes. If LFS is

open and "WTRIN" LED is off, conrm LFS status. See "II.E. Float Switch Check and

Cleaning." If LFS is open and "WTRIN" LED is off, replace CB. If "WTRIN" LED is on

and WV is not energized, check for 24VAC at CB K2 #8(O) to a neutral (LBU). If24VAC

is not present at CB K2 #8(O), replace CB. "WTRIN" LED turns off once UFS closes.

Ifnot, conrm UFS status. See "II.E. Float Switch Check and Cleaning." IfUFS is

closed and "WTRIN" LED is on, replace CB. If "WTRIN" LED is off and WV is open,

check for 24VAC at CB K2 #8 (O). If 24VAC is present at CB K2 #8 (O), replace CB.

If24VAC is not present, check WV diaphragm.

6) Ice Purge Cycle "GM" LED is on: When UFS closes, GM delay timer starts (5 or

30sec. depending on CB S1 dip switch #7). Once GM delay timer terminates, "GM"

LED turns on, GM and EH (-C model) energize and 5-min. ice purge timer starts. If GM

does not energize 5 sec. after UFS closes, conrm UFS status. See "II.E. Float Switch

Check and Cleaning." If UFS is closed and GM LED does not turn, replace CB. If "GM"

LED is on and GM and EH (-C model) are off, check for 115VAC from CBK1#2 (BK)to

a neutral (W). If 115VAC is not present, check 115VAC power supply connections from

power switch. If 115VAC is present, check for 115VAC from CB K1 #3 (P)to a neutral

(W). If115VAC is present on CB K1 #2 (BK)and not on CB K1 #3 (P), replace CB.

7) Freeze Cycle "GM" and "COMP" LED are on: The 5-min. ice purge timer terminates

or the ice purge cycle bypass button ("SERVICE") is pressed, "COMP" LED turns on.

Tobypass the 5-min. Ice Purge Cycle, press the "SERVICE" button on CB after the

"GM" LED turns on. WARNING! Risk of electric shock. Care should be taken not to

touch live terminals. 115VAC is present between CB X1 relay power supply black (BK)

wire and neutral (W) at all times. If not, check 115VAC power supply wire connections

from power switch. If"COMP" LED is not on after 5-min. ice purge timer terminates,

replace CB. When "COMP" LED turns on, CR and Comp energize. If "COMP" LED is

on and compressor relay (CR) and Comp are not, check for 115VAC from CB X1 relay

power supply black (BK) wire to neutral (W). If 115VAC is present, check X1 relay violet

(V) wire to neutral (W). If 115VAC is present on X1 relay black (BK) and not on X1 relay

violet (V), replace CB.

8) Rell "WTRIN" LED is on: See "5) Fill "WTRIN" LED is on:" above.

9) Shutdown:See "I.C.3)D) Bin Control" above.

Legend: BC–bin control; CB–control board; Comp–compressor; CR–compressor relay;

CCR–compressor control relay; EH–evaporator heater (-Cmodel); FS–oat switch;

GM–gear motor; LFS–lower oat switch; UFS–upper oat switch; WV–inlet water

valve

Page is loading ...

Hoshizaki F-330BAJ, F-330BAJ-C User manual

Related papers

Other documents