Samsung SA8000 SE User manual

Brand: Samsung

Model: SA8000 SE

Type: User manual

Chapter 4

Diagnosis Modes

Diagnosis Mode Types and Control ............................................................................... 2

Diagnosis Mode Type ............................................................................................................... 2

Changing Diagnosis Mode Format ........................................................................................... 2

Diagnosis Modes Optimization ................................................................................................. 4

Basic Mode..................................................................................................................... 6

2D Mode ................................................................................................................................... 6

M Mode ..................................................................................................................................... 9

Color Doppler Mode................................................................................................................ 11

Power Doppler Mode ..............................................................................................................14

Spectral Doppler Mode ...........................................................................................................15

Combined Mode ........................................................................................................... 20

B/C/PW Mode ......................................................................................................................... 20

B/PD/PW Mode....................................................................................................................... 20

B/C/CW Mode......................................................................................................................... 21

B/PD/CW Mode ...................................................................................................................... 22

B/C/M Mode............................................................................................................................ 22

Multi-Image Mode......................................................................................................... 23

Dual-2D Mode......................................................................................................................... 23

Dual-2D/Color Doppler Mode ................................................................................................. 23

Dual-2D/PD Mode................................................................................................................... 24

3D Mode....................................................................................................................... 25

3D ........................................................................................................................................... 25

Acquiring a 3D Image ............................................................................................................. 26

3D View................................................................................................................................... 26

4 - 2 SA8000 SE Operation manual

Diagnosis Mode Types and Control

Diagnosis Mode Type

This product supports a variety of diagnosis modes including Basic mode, Combined mode,

Multi-Image mode, and 3D mode.

■ Basic Mode

2D Mode, Color Doppler Mode, Power Doppler Mode, M Mode, PW Spectral Doppler

Mode, CW Spectral Doppler Mode.

■ Combined Mode

M Mode, PW Spectral Doppler Mode and CW Spectral Doppler Mode can be added in

Color Doppler Mode or Power Doppler Mode. Five types of Combined Mode are

supported.

■ Multi-Image Mode

In Dual Mode you can view two images side by side simultaneously and compare them.

■ 3D Mode

3D images can be obtained. Provides the Freehand 3D option, which allows viewing of

three-dimensional images.

Changing Diagnosis Mode Format

The following section explains how to change the display format that is common to all diagnosis

modes.

▐ Changing Display Format

Use the Flexible Soft button [4] Loop Format.

M Mode, PW Spectral Doppler Mode, or CW Spectral Doppler Mode provide two display

formats.

In M mode and PW Spectral Doppler Mode, Top Down Format sets the images at the top

and bottom of the screen. Side-by-Side Format sets the images side by side.

Chapter4. Diagnosis Modes 4 - 3

▐ Changing Active Image

In Dual Mode, the control functions and screen menu configuration differ depending on the

active image. To change the Flexible soft menu of currently activated mode, press the

keyboard space bar.

For example, you can change the currently active image in PW Spectral Doppler Mode Æ

2D Mode Æ Color Doppler Mode order by pressing the space bar if 2D Mode is activated

in B/C/PW Mode.

However, the keyboard space bar is inactive in Freeze mode.

▐ Changing Flexible Soft Menu

Use the keyboard space bar to move from Combined Mode to Flexible Soft Menu.

In B/C/D Mode, for example, you can change Flexible Soft Menu in PW Sepctral Doppler

Mode to Flexible Soft Menu in Color Doppler Mode by pressing the space bar.

▐ Changing Activated Image Position in Multi-Image Mode

Use Set button or Dual button on the control panel.

For example, press Set button or Dual button in Dual-2D Mode. The image that is being

scanned is frozen in the left section of the screen, and the right image becomes active.

▐ Freezing 2D Image in Spectral Doppler Mode

When 2D and PW Spectral Doppler images are showing simultaneously, press Set button

on the control panel to freeze the 2D image for closer observation of Doppler images.

Press Set button again to reactivate the image.

When Simultaneous Mode is off, the current image mode is shown as PW Only, CW Only

or 2D Only in the upper right portion of the screen. Activation of Simultaneous Mode is set

in the Misc. tab in the Setup window. If you set ‘Simultaneous Mode’ is ‘Off’, the item

‘Simultaneous’ on the PW Spectral Doppler mode will not be activated.

▐ Image Depth Control

Raise/lower the Depth switch to decrease/increase the scanning depth of an image. The

maximum/minimum depth depends on the probe used.

▐ Image Magnification

Use the HD Zoom switch on the control panel to save the magnified image. Raise the

switch, and the HD Zoom Box appears. Use the Change button and trackball to set the

position and size of the HD Zoom Box. Press the Change button to toggle between Zoom

Pos. and Zoom Size; the selection will be indicated on the left side of the screen.

4 - 4 SA8000 SE Operation manual

- Zoom Position: Press the Change button and the HD Zoom Box lines become solid

lines. Use the trackball to move the box to the desired position.

- Zoom Size: Press the Change button and the HD Zoom Box lines become dotted

lines. Use the trackball to change the size of the box.

After adjusting its position and size with the Trackball, press the Set button to enter HD

Zoom Mode. You can view the position of the magnified area through the Zoom

Navigation Box on the screen.

In HD Zoom mode, press the Z key on the keyboard to make the Zoom Navigation Box

disappear and Zoom Position deactivate. Press Z key again, and the Zoom Navigation

Box is shown again.

Adjust Depth switch or press Exit button to exit HD Zoom Mode.

Read Zoom

This function magnifies an image saved in the memory. Press the Zoom button on the

control panel to start Read Zoom mode.

In HD Zoom mode, it is available to press the Zoom button on the control panel to

start the Read Zoom mode. However, in Read Zoom mode, you cannot enter the HD

Zoom mode with the Zoom button.

Diagnosis Modes Optimization

For optimizing images, the following functions are common to all modes.

▐ Gain Control

Use the D-Gain, C-Gain, or B-Gain dials on the control panel to adjust image brightness.

If you rotate the Gain dial clockwise, its value increases, and vice versa.

▐ TGC Control

Ultrasound penetration gets weaker with depth. Six TGC slides are available for optimal

image output. Adjust Gain according to depth.

Move the TGC slide to the right(+) to increase Gain (brightening the image) and vice versa.

▐ Frequency Change

Use the Frequency button on the control panel to obtain the optimal image by changing

the frequency. The meanings of the frequencies are shown below.

Chapter4. Diagnosis Modes 4 - 5

▐ Focus Position Control

Raise/lower the Focus switch raise/lower the focusing point.

▐ Harmonic Function

Press the Harmonic button on the control panel in 2D Mode. When the Harmonic function

is used, ‘HGen.’, ‘HRes.’ and ‘HPen.’ are displayed in the probe information section.

The Harmonic function is only activated with the specific probe.

▐ Power Control

Power is the intensity of the acoustic output.

Use the Menu dial-button on the control panel to set the Power, in the left menu. Its value

ranges from 10 to 100.

4 - 6 SA8000 SE Operation manual

Basic Mode

2D Mode

This basic mode, also referred to as B Mode (Brightness mode), shows anatomy scan planes.

[Figure 4.1 2D Mode]

[Figure 4.2 2D Menu]

▐ 2D Mode Selection

Press the 2D button on the control panel.

2D Mode is the default mode and the 2D button is not a toggle button. Instead, it is used to

return to basic 2D Mode when in other image modes.

Chapter4. Diagnosis Modes 4 - 7

▐ Changing 2D Image Format

Changing Image Direction

- Changing Left/ Right Orientation (Horizontal Orientation Direction)

Press the Flexible Soft button [5] Direction.

- Changing Up/down Orientation (Vertical Orientation. Apex)

Select Apex in the 2D menu using the Menu dial-button.

Changing View Area

Select View Area in the menu using the Menu dial-button on the control panel.

You can adjust View Area using the Size + and Size – buttons in the Flexible Soft Menu.

Widening/narrowing the View Area, decreases/increases the frame rate (FPS). If you want

to view other unseen parts, press the Pos.L and Pos.R buttons in Flexible Soft Menu to

move the View Area to the right or left.

[Figure 4.3 Flexible Soft Menu when changing View Area]

The changed view area value is displayed in the lower right-hand portion of the screen.

Pressing the Flexible Soft button [5] Return makes the value disappear.

M Line Display

Indicates where the image for M Mode or PW Spectral Doppler Mode appears in the 2D

image.

Pressing the Flexible Soft button [4] M Line makes the M Line appear or disappear.

▐ 2D Image Optimization

Frame Average Control

The Frame Average function is used to average frames together on the screen, thereby

reducing the speckles which make diagnosis difficult. Setting the Frame Average value as

high makes the display movements smoother but slower. (Though the actual frame rate

doesn’t drop.) Turn the function off in OB and cardiac examination where organs are

highly active.

Use the Menu dial-button on the control panel to press FA in the menu. The values range

from 0 to 9.

Dynamic Range Control

This function is used to change the range of contrast by adjusting the ratio of

4 - 8 SA8000 SE Operation manual

minimum/maximum input signal value ratio. Increase/decrease Dynamic Range to

smooth/roughen the image.

Use the Menu dial-button on the control panel to press DR in the left menu. Select a value.

Edge Enhance Control

This function is used to view more accurate images of organ or tissue boundaries.

Increase the Edge Enhance value to obtain clearer pictures of boundaries.

Use the Menu dial-button on the control panel to press EE in the menu. Select a value.

Reject Level Control

This function is used to eliminate noise or low level echoes for clearer signals.

Use the Menu dial-button on the control panel to press Reject in the left menu. Select a

value.

Focus Number Control

Use the Menu dial-button on the control panel to press Focus No in the menu. Or press

the Flexible Soft button [1] Focus No, and set the Focus Number with the Soft Menu

Focus + and Focus – buttons.

Frame Rate Control

The Frame Rate is the number of images generated per second. The Frame Rate should

be set to Fast when viewing fast moving organs. Select Fast, Normal, or Slow using the

Menu dial-button on the control panel.

Tissue Property Control

Select the desired ultrasound speed according to the patient’s tissue type. The Tissue

menu consists of Cystic, Adipose, Normal, and Solid.

Use the Menu dial-button on the control panel to select Tissue in the menu.

Trapezoid Function

This function is used to view the trapezoid-shaped 2D image when using the Linear probe.

Use the Menu dial-button on the control panel to select Trapezoidal in the menu.

When adjusting image depth, some depth values do not support the Trapezoid function.

When the Trapezoid function is on, the Zoom button is inactivated.

Chapter4. Diagnosis Modes 4 - 9

M Mode

In M Mode, you can observe the motion patterns of an area of anatomy - along a 2D image

reference line (M Line). This mode is especially useful for cardio-valvular observation.

[Figure 4.4 M Mode]

[Figure 4.5 M Mode Flexible Soft Menu]

▐ M Mode Selection

Press the M button on the control panel. Press M button again. M Mode turns off and 2D Mode

turns on.

4 - 10 SA8000 SE Operation manual

▐ Changing M Mode Format

Image Direction Change

Select Direction using the Menu dial-button on the control panel in M Mode.

M Line Control

Move the M Line to change the observation location. The M Line can be moved left and

right by using the Trackball on the control panel.

M Image Size Change

To adjust the size (Large, Normal or Small) of the 2D image and the M image, use the

Menu dial-button on the control panel to select M Size from the menu or select an M

Mode image size with the Flexible Soft button [1] M Size.

Sweep Speed Control

You can choose from 120Hz, 180Hz, 240Hz or 300Hz with the Speed button on the

control panel.

Loop Format Change

Select Top Down Format or Side-by-Side Format using the Flexible Soft button [4] Loop

Format. Top Down Format sets the 2D image and M image at the top and bottom of the

screen. Side-by-Side Format sets the images side by side.

NOTE

Refer to `2D Mode’ for more information about other items in the menu.

Chapter4. Diagnosis Modes 4 - 11

Color Doppler Mode

In this mode you can obtain a variety of information about blood flow within the 2D Image such

as the existence of blood flow, its average speed and its direction within the ROI (Region of

Interest).

[Figure 4.6 Color Doppler Mode]

[Figure 4.7 Color Doppler Mode Menu]

▐ Color Doppler Mode Selection

Press the C button on the control panel.

Pressing C button again turns Color Doppler Mode off and 2D Mode on.

4 - 12 SA8000 SE Operation manual

▐ Changing Color Image Format

Controlling Color Bar Baseline Control

The colors above the baseline represent the direction/speed of blood flow moving toward

the probe, and the colors below the baseline represent the direction/speed of blood flow

away from the probe.

Use the Baseline switch on the control panel. If you raise the switch, the Color Bar

Baseline is raised, and vice versa.

Baseline can be adjusted only when the Color Doppler Mode value is set to Velocity.

Color Bar Invert

Press the Invert button on the control panel to invert the color bar and the colors on the

image.

Changing Color Display Information

Select Color Mode in C-Menu using the Menu dial-button on the control panel.

Use the Menu dial-button to cycle through the available settings - Velocity, Power,

Variance, and Vel + Var.

▐ Color Image Optimization

Changing ROI Box Position

The ROI is the area within the 2D image where color (blood flow) information is displayed

in Color Doppler Mode. Use the Trackball to change the ROI Box position.

Changing ROI Box Size

Enter the ROI Box Size Control Mode by rotating the Menu dial-button without opening the

pop-up menu or pressing the Change button on the control panel. Adjust the ROI Box size

with the Trackball. To return to the ROI Box Position Change Mode, rotate the Menu dial-

button without opening the pop-up menu or press Change button again.

Scale (PRF) Control

Use the Scale switch on the control panel. If you raise/lower the switch, PRF (Pulse

Repetition Frequency) increases/decreases so that the speed range of blood flow is

widened/narrowed.

Wall Filter Control

Wall filter is an electrical filter used to eliminate low-frequency Doppler signals caused by

the motions of vessel walls. Eliminate Doppler signals whose frequencies are lower than

the Cutoff Frequency by adjusting the Cutoff Frequency.

Chapter4. Diagnosis Modes 4 - 13

Use the Filter switch on the control panel. If you raise the Filter switch, the Cutoff

Frequency of the Wall Filter decreases, and vice versa.

Sensitivity Control

Select Sensitivity in the menu using the Menu dial-button on the control panel or use the

Flexible Soft button [1] Sensitivity to adjust the value (8~31).

To increase/decrease Sensitivity, raise/lower the Sensitivity value. Increasing the Color

Sensitivity decreases the frame rate, and vice versa.

Balance Control

This function is used to adjust the range of the color image displayed by comparing the

gray level of the 2D image with the Doppler signal value of the color image. If the Balance

value increases, the color image is seen even where the 2D image signal is strong (bright),

thereby increasing the color image range.

Select Balance using the Menu dial-button on the control panel and adjust the value

(1~16).

Steer Function

When Linear probe is selected, this function adjusts the ultrasound beam angle to prevent

the loss of color information caused by the ultrasound beam angle.

Pressing the Steer button on the control panel steers the ROI to the left, center and right -

in that order.

Display Function

Color Doppler Mode supports Color + B/W Image, Color Only, and B/W Only display.

Select Display in the menu using the Menu dial-button on the control panel. In Freeze,

use the Flexible Soft Button [5] to select the function.

TDI (Tissue Doppler Image) Function

This function is used to show the movements of the cardiac tissues. To use the TDI

function, use the Menu dial-button on the control panel to select Tissue Doppler from the

menu on the left-hand side of the screen.

It uses the color information of Color Doppler Mode or Power Doppler Mode. It also uses

the change of cardiac tissue of PW Spectral Doppler Mode as time goes by. It is only used

in the specific application (General, Cardiac, Pediatric) of Phased Array probe.

NOTE

For further information about other items in the menu, refer to ‘2D Mode’.

4 - 14 SA8000 SE Operation manual

Power Doppler Mode

Instead of the speed or direction of blood flow, Power Doppler Mode displays the overall

strength of blood flow, thereby showing information about the existence and amount of blood

flow in the sample area.

[Figure 4.8 Power Doppler Mode]

[Figure 4.9 Power Doppler Mode Menu]

▐ Power Doppler Mode Selection

Press the PD button on the control panel. Pressing PD button again turns PD Mode off,

and 2D Mode on.

▐ PD Mode Screen

Color Bar

Colors show the existence and amount of blood flow in PD Mode. The top of the color bar

is the brightest section, where the amount of blood flow is at its highest.

NOTE

For further information about other PD Image optimization, refer to ‘Color

Doppler Mode’.

Chapter4. Diagnosis Modes 4 - 15

Spectral Doppler Mode

Spectral Doppler Mode gives information on the speed/direction of blood flow at a specific site

in the form of a spectral trace and audio signal. It is divided into PW (Pulsed Wave) Spectral

Doppler Mode and CW (Continuous Wave) Spectral Doppler Mode.

▐ PW Spectral Doppler Mode

PW Spectral Doppler Mode gives information on the speed of blood flow at a specific site in

the form of a spectral trace and audio signal. Since the pulse is transmitted being divided

according to time, distance (depth) information can be obtained. The mode is suitable for

measuring relatively slow blood flow such as that in abdominal and peripheral vessels. The

2D Mode image is shown simultaneously allowing the marking and adjustment of specific

sites within blood vessels.

Press the D button on the control panel. Press D button again to enter 2D Mode.

[Figure 4.10 PW Spectral Doppler Mode]

[Figure 4.11 PW Spectral Doppler Mode menu]

4 - 16 SA8000 SE Operation manual

▐ CW Spectral Doppler Mode (Optional)

CW Spectral Doppler Mode gives information on the speed/direction of blood flow in the

form of a spectral trace and audio signal. The 2D Mode image is shown simultaneously

allowing the marking and adjustment of specific sites within blood vessels.

Press the CW button on the control panel. Press CW button again to enter 2D Mode.

[Figure 4.12 CW Spectral Doppler Mode]

[Figure 4.13 CW Spectral Doppler Mode menu]

▐ Spectral Doppler Mode Screen

On the Spectral Doppler Mode image, the horizontal axis represents time, and the vertical

axis represents speed (or frequency).

Sample Volume

When Sample Volume is on the blood flow of 2D image, it represents Doppler Spectrum.

Its position is moved with the Trackball and displayed in the [email protected] mm format. The

Chapter4. Diagnosis Modes 4 - 17

format means that the Sample Volume of ‘xx.x’ mm size is located at a depth of ‘yy.y’ mm.

For example, [email protected] mm means that the Sample Volume of 2.0mm size is located at a

depth of 16.7mm.

NOTE

Sample Volume is available only in PW Spectral Doppler Mode.

▐ Spectral Doppler Mode Format Change

Changing PW Spectral Doppler Image Size

To adjust the image position, the 2D image is shown together. The size of the 2D image

and PW Spectral Doppler image can be changed.

Select PW Size in the menu using the Menu dial-button on the control panel. Or press the

Flexible Soft button [1] PW Size to select the size (Large, Normal, or Small).

This function is activated in Simultaneous mode is on.

Activating Simultaneous Function

The PW Spectral Doppler image and 2D image can be displayed simultaneously or

separately. This function is not available in Steered CW Spectral Doppler Mode.

Select Simultaneous in the menu using the Menu dial-button on the control panel. If

Simultaneous is selected again when this mode is already on, the mode is deactivated.

Activate the Simultaneous function option by setting Simultaneous function as ‘Allow

2D/PW’ or ‘Allow 2D/C/PW’in the Misc. tab in the Setup window.

NB. Simultaneous function decreases Doppler PRF, thus decreasing the measurable

speed range.

Doppler Baseline Control

Raise/lower the Baseline switch on the control panel to raise/lower the Baseline.

Doppler Axis Invert

Press the Invert button on the control panel. The ‘+ velocity value’ and ‘- velocity value’,

shown at the Doppler axis, change positions.

Loop Format Change

Select Loop Format in the menu using the Menu dial-button on the control panel. Or

press Flexible Soft button [4] Loop Format to select Loop Format. ‘Hor’ means Top

Down Format, in which 2D image is set above the PW Spectral Doppler image, and ‘Ver’

means Side by Side Format, in which the two images are set side-by-side.

4 - 18 SA8000 SE Operation manual

▐ Spectral Doppler Image Optimization

Sample Volume Position Control

Use the Trackball on the control panel.

Sample Volume Size Control

Adjust the Sample Volume size by pressing the Change button and using the Trackball

on the control panel. Press Change button again to return to the Sample Volume Position

Control screen. The icon showing the two Trackball functions (SV Pos/SV Size) is shown

for a second and disappears.

Sample Volume Angle Control

Use the Angle dial to adjust the angle for accurate measurement of speed.

Doppler Sound Volume Control

Use the Audio Slide Volume control on the control panel.

Average Control

The Average Control is used to increase spectrum quality.

Select Average in the menu using the Menu dial-button on the control panel. Select the

Average value (Low, Middle or High).

Spectrum Enhancement

The Spectrum Enhancement is used to compensate the signal of low gain Spectral

Doppler Spectrum. This function is available in Loop Only Mode or Simultaneous Function

and is not available in TDI function.

Select Spectrum Ehc. In the menu using the Menu dial-button on the control panel.

Select the value from 1 to 8.

HPRF (High PRF) Function

This function measures blood flow whose speed exceeds specified limits at a specified

depth. It doubles the original scale. This function is available only in PW Spectral Doppler

Mode.

NOTE

To use HPRF function, select ‘On’ in the Setting>System>Misc. tab.

- HPRF Activation

To activate HPRF, increase the Scale values at the required depth. The Phantom Gate

appears over the sample volume in D Line. Once HPRF is activated, the PRF doesn’t

increase even if the scale values are raised.

Chapter4. Diagnosis Modes 4 - 19

[Figure 4.14 HPRF]

- HPRF Exit

To exit HPRF, decrease Scale values by one notch while HPRF is activated. The

maximum PRF values in PW Spectral Doppler Mode are shown.

- Sample Volume Position Control

To move the Sample Volume position in the PW Only status, the system calculates PRF

values and the Phantom Gate position, and updates them on the PW Spectral Doppler

image. Exit HPRF when HPRF cannot be activated.

When Sample Volume is moved in the 2D Only status, the PRF values don’t change. In

PW Only status, the PRF values and Phantom Gate position are calculated and updated

on the PW Spectral Doppler image.

NOTE

HPRF is not activated in Simultaneous Mode. It is also not activated if

[PRF*2] exceeds 23KHz.

CAUTION

■ The Phantom Gate position can be located outside the 2D image area in

Zoom Mode.

■ Ensure that the Sample Volume and Phantom Gate are not positioned

over the area to be measured. If more than two SVs are located in the

vessels, all Doppler components will appear in the spectrum, causing

noise.

NOTE

For further information about Wall Filter, Dynamic Range and Steer Control,

refer to ‘2D Mode’ and ‘Color Doppler Mode’.

4 - 20 SA8000 SE Operation manual

Combined Mode

B/C/PW Mode

Color Doppler Mode and PW Spectral Doppler Mode are displayed simultaneously.

Press the D button on the control panel in Color Doppler Mode. In PW Spectral Doppler Mode

press the C button.

[Figure 4.15 B/C/PW Mode]

B/PD/PW Mode

PD Mode and PW Spectral Doppler Mode are displayed simultaneously.

Press the D button on the control panel in PD Mode. In PW Spectral Doppler Mode press the

PD button.

Page is loading ...

Samsung SA8000 SE User manual

Samsung SA8000 SE User manual

Samsung SA8000 SE User manual

Related papers

Other documents