COMFORT-AIRE HRC09A1CAMSCFL User guide

Heat Controller • 1900 Wellworth Ave. • Jackson, MI 49203 • (517)787-2100 • www.heatcontroller.com

ENGINEERING

DESIGN GUIDE

HRC Series

Commercial Console

Water-Source Heat Pumps

60Hz

Design Guide HRC SERIES Heat Controller

2

Heat Controller HRC SERIES Design Guide

Table of Contents

*Page Number

Unit Features ..................................................................................4

Selection Procedure ............................................................................5

HRC Series Nomenclature .......................................................................7

Performance Data – AHRI/ASHRAE/ISO 13256-1 .....................................................8

Performance Data – Selection Notes ...............................................................9

Performance Data – HRC09 .....................................................................10

Performance Data – HRC12 .....................................................................11

Performance Data – HRC15 .....................................................................12

Performance Data – HRC18 .....................................................................13

Performance Data Correction Tables ..............................................................14

Blower Performance & Electrical Data .............................................................15

Physical Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Console Cabinet Dimensions Size 09 -15 - Bottom Return - Left Hand Piping ...............................17

Console Cabinet Dimensions Size 09 - 15 - Front Return - Left Hand Piping ................................18

Console Cabinet Dimensions Size 09 - 15 - Bottom Return - Right Hand Piping .............................19

Console Cabinet Dimensions Size 09 - 15 - Front Return - Right Hand Piping ..............................20

Console Bottom Return Chassis Dimensions Size 09 - 15 ..............................................21

Console Front Return Chassis Dimensions Size 09 - 15 ...............................................22

Piping Detail Size 09-15 ........................................................................23

Console Cabinet Dimensions Size 18 - Bottom Return - Left Hand Piping ..................................24

Console Cabinet Dimensions Size 18 - Front Return - Left Hand Piping ...................................25

Console Cabinet Dimensions Size 18 - Bottom Return - Right Hand Piping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Console Chassis Dimensions Size 18 - Front Return - Right Hand Piping ..................................27

Console Bottom Return Chassis Dimensions Size 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Console Chassis Dimensions Size 18 ..............................................................29

Piping Detail Size 18 ...........................................................................30

HRC Series Wiring Diagram Matrix ...............................................................31

Typical Wiring Diagram – Manual & Auto Change Over HRC Units with CXM Controller .......................32

Typical Wiring Diagram – Remote Mounted Thermostat HRC Units with CXM Controller ......................33

Typical Wiring Diagram – HRC Units with CXM & LON Controller ........................................34

Typical Wiring Diagram – HRC Units with CXM & MPC Controller ........................................35

Typical Wiring Diagram – Manual & Auto Change Over HRC Units with DXM Controller .......................36

Typical Wiring Diagram – Remote Mounted Thermostat HRC Units with DXM Controller ......................37

Typical Wiring Diagram – HRC Units with DXM & LON Controller ........................................38

Typical Wiring Diagram – HRC Units with DXM & MPC Controller ........................................39

Engineering Specications ......................................................................40

Revision History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

3

Design Guide HRC SERIES Heat Controller

CONSOLE (HRC) SERIES

WITH HFC-410A REFRIGERANT

The Series (HRC) console unit provides a high efciency

WSHP “ductless” solution for spaces where individual,

quiet control of the heating and cooling system is

important. HRC units are especially ideal where ceiling

height and space are limited, or when preserving the

integrity of an existing structure. The HRC Series

exceeds ASHRAE 90.1 efciencies, yet maintains small

cabinet dimensions. Using

HFC-410A

refrigerant, the

console not only protects the environment, it does so

while delivering unprecedented comfort, efciency, and

reliability.

Available in sizes 3/4 ton (2.64 kW) through 1-1/2 tons

(5.3 kW) with numerous cabinet, water piping and control

choices, the HRC Series offers a wide range of units for

most any installation. The HRC has an extended range

refrigerant circuit, capable of ground loop (geothermal)

applications as well as water loop (boiler-tower) appli-

cations. Standard features are many. Microprocessor

controls, galvanized steel cabinet, polyester powder coat

paint and TXV refrigerant metering device are just some

of the features of the exible HRC series.

Compressors are mounted on specially engineered

sound-tested EPDM grommets for quiet operation.

Options such as coated air coil, DDC controls, internal

pump and factory-installed water solenoid valves allow

customized design solutions.

The HRC Series console water-source heat pumps

are designed to meet the challenges of today’s HVAC

demands with a low cost/high value “ductless” solution.

UNIT FEATURES

Sizes 09 (3/4 ton, 2.64 kW) through 18 (1-1/2 ton, 5.3 kW

Environmentally-friendly (HFC-410A) zero ozone

depletion refrigerant

High Efficiency Rotary compressors

Exceeds ASHRAE 90.1 efficiencies

Two-piece chassis/cabinet design

Galvanized steel cabinet with durable Polar Ice powder

coat finish and black “matte” finish on subbase

Slope top/aluminum rigid bar supply air grille

UltraQuiet Option

TXV metering device

Extended range (20 to 120°F, -6.7 to 48.9°C) operation

Advanced digital auto change-over unit mounted controls

with temperature display and high/low fan speed

selection

Remote-mounted controls available

Microprocessor controls standard (optional DXM and/or

DDC controls)

LonWorks, BACnet, Modbus and Johnson N2

compatibility options for DDC controls

Right or left-hand piping arrangement

Front or bottom return air configuration

Unit Performance Sentinel

™

performance

monitoring system

Eight Safeties Standard

Wide variety of options including coated air coil, flow

regulator, motorized water valve, stainless steel

drain pan, locking control door, disconnect switch,

and internal pump. (Pump option requires extended

cabinet).

Accessory

Louvered, painted black “matte” finish subbase

decorative grille for field-installation.

Unit Features

4

Heat Controller HRC SERIES Design Guide

To convert Inch-Pound (English) to SI (Metric)

Air Flow Correction Table

400 CFM per ton of cooling capacity is nominal rated airflow for all models (bold print)

Use multipliers directly with unit data for correcting unit performance at other airflows than nominal

Entering Air Correction Tables

Entering air corrections should be multiplied directly to unit performance data to derive performance at entering air condition other

than ARI/ISO/ASHRAE 13256-1

ARI/ISO/ASHRAE 13256-1 uses entering air conditions of Clg- 80.6ϒF DB/66.2ϒF WB and Htg- 68ϒF DB/59ϒF WB shown in bold

Discontinued Standards ARI 320, 325, and 330 used entering air conditions of Clg- 80ϒF DB/67ϒF WB and Htg- 70ϒF DB

Cooling Corrections

Sens Clg Cap Multiplier - Entering DB ϒF

Ent Air

WB ϒF

Total Clg

Cap

70 75 80 80.6 85 90 95

Power Heat of

Rej

60 0.852 0.828 0.980 1.097 1.129 ***0.996 0.878

65 0.974 0.595 0.808 1.004 1.017 1.194 **0.998 0.979

66.2 1.000 0.539 0.767 0.967 1.000 1.152 **1.000 1.000

67 1.004 0.501 0.740 0.939 0.955 1.124 1.233 1.276 1.002 1.010

70 1.034 0.636 0.810 0.844 1.016 1.136 1.220 1.005 1.029

75 1.069 0.514 0.612 0.826 0.973 1.127 1.010 1.058

Heating Corrections

Ent Air

DB ϒF

Htg Cap Power

Heat of

Ext

60 1.059 0.947 1.100

65 1.019 0.981 1.032

68 1.000 1.000 1.000

70 0.995 1.010 0.989

75 0.980 1.037 0.960

80 0.967 1.063 0.934

Total Cap Sens Cap Power Heat of Rej

1.019 0.902 0.964 1.007

1.013 0.928 0.976 1.003

1.007 0.953 0.988 1.000

1.004 0.977 0.994 1.000

1.000 1.000 1.000 1.000

0.998 1.023 1.006 1.000

0.997 1.047 1.012 1.000

Cooling

CFM Per Ton

of Clg

% of

Nominal

300 75%

325 81%

350 88%

375 94%

400 100%

425 106%

450 113%

Airflow

Htg Cap Heat of ExtPower

0.957 1.061 0.922

0.968 1.040 0.946

0.979 1.020 0.970

0.989 1.010 0.985

1.000 1.000 1.000

1.0110.997 1.015

1.021 0.994 1.030

Heating

Air Flow Water Flow Ext Static Pressure Water Pressure Drop

Airflow (L/s) = CFM x 0.472 Water Flow (L/s) = gpm x 0.0631 ESP (Pa) = ESP (in of wg) x 249 PD (kPa) = PD (ft of hd) x 2.99

Reference Calculations

BTUH = BTU( British Thermal Unit) per hour

CFM = airow, cubic feet/minute

COP = coefcient of performance = BTUH output/BTUH input

DB = dry bulb temperature (°F)

EAT = entering air temperature, Fahrenheit (dry bulb/wet bulb)

EER = energy efciency ratio = BTUH output/Watt input

MPT = male pipe thread

ESP = external static pressure (inches w.g.)

EWT = entering water temperature

GPM = water ow in U.S. gallons/minute

HE = total heat of extraction, BTUH

HC = air heating capacity, BTUH

HR = total heat of rejection, BTUH

HWC = hot water generator (desuperheater) capacity, Mbtuh

FPT = female pipe thread

KW = total power unit input, kilowatts

LAT = leaving air temperature, °F

LC = latent cooling capacity, BTUH

LWT = leaving water temperature, °F

MBTUH = 1000 BTU per hour

S/T = sensible to total cooling ratio

SC = sensible cooling capacity, BTUH

TC = total cooling capacity, BTUH

WB = wet bulb temperature (°F)

WPD = waterside pressure drop (psi & ft. of hd.)

Conversion Table - to convert inch-pound (English) to S-I (Metric)

Legend and Glossary of Abbreviations

LWT = EWT -

HE

GPM x 500

LAT = EAT +

HC

CFM x1.08

LWT = EWT +

HR

GPM x 500

LAT (DB) = EAT (DB) -

SC

CFM x1.08

LC = TC - SC

S/T =

SC

TC

Heating

Cooling

Selection Procedure

5

Design Guide HRC SERIES Heat Controller

Selection Procedure

Step 1 Determine the actual heating and cooling loads at the

desired dry bulb and wet bulb conditions.

Step 2 Obtain the following design parameters: Entering water

temperature, water ow rate in GPM, air ow in CFM,

water ow pressure drop and design wet and dry bulb

temperatures. Air ow CFM should be between 300 and

450 CFM per ton. Unit water pressure drop should be

kept as close as possible to each other to make water

balancing easier. Go to the appropriate tables and nd

the proper indicated water ow and water temperature.

Step 3 Select a unit based on total and sensible cooling

conditions. Select a unit which is closest to, but no

larger than, the actual cooling load.

Step 4 Enter tables at the design water ow and water

temperature. Read the total and sensible cooling

capacities (Note: interpolation is permissible,

extrapolation is not).

Step 5 Read the heating capacity. If it exceeds the design

criteria it is acceptable. It is quite normal for Water-

Source Heat Pumps to be selected on cooling capacity

only since the heating output is usually greater than the

cooling capacity.

Step 6 Determine the correction factors associated with the

variable factors of dry bulb and wet bulb.

Corrected Total Cooling = tabulated total cooling

x wet bulb correction.

Corrected Sensible Cooling = tabulated sensible cooling

x wet/dry bulb correction.

Step 7 Compare the corrected capacities to the load

requirements. Normally if the capacities are within 10%

of the loads, the equipment is acceptable. It is better

to undersize than oversize, as undersizing improves

humidity control, reduces sound levels and extends the

life of the equipment.

Step 8 When completed, calculate water temperature rise

and assess the selection. If the units selected are not

within 10% of the load calculations, then review what

effect changing the GPM, water temperature and/or air

ow and air temperature would have on the corrected

capacities. If the desired capacity cannot be achieved,

select the next larger or smaller unit and repeat the

procedure. Remember, when in doubt, undersize

slightly for best performance.

Example Equipment Selection For Cooling

Step 1 Load Determination:

Assume we have determined that the appropriate cooling load

at the desired dry bulb 80°F and wet bulb 65°F conditions is as

follows:

Total Cooling.........................................................10,200 BTUH

Sensible Cooling.....................................................8,350 BTUH

Entering Air Temp.........................80°F Dry Bulb/65°F Wet Bulb

Step 2 Design Conditions:

Similarly, we have also obtained the following design

parameters:

Entering Water Temp..........................................................90°F

Water Flow (Based upon 12°F rise in temp.)...............2.3 GPM

Air Flow........................................................................350 CFM

Step 3, 4 & 5 HP Selection:

After making our preliminary selection (HRC12), we enter the

tables at design water ow and water temperature and read

Total Cooling, Sens. Cooling and Heat of Rej. capacities:

Total Cooling.........................................................10,800 BTUH

Sensible Cooling.....................................................9,200 BTUH

Heat of Rejection..................................................13,900 BTUH

Step 6 & 7 Entering Air and Airow Corrections:

Next, we determine our correction factors.

Table Ent Air Air Flow Corrected

Corrected Total Cooling = 10,800 x 0.976 x 0.954 =10,056

Corrected Sens Cooling = 9,200 x 1.071 x 0.927 = 9,134

Corrected Heat of Reject = 13,900 x 0.979 x 0.958 = 13,037

Step 8 Water Temperature Rise Calculation & Assessment:

Actual Temperature Rise....................................................11.3°F

When we compare the Corrected Total Cooling and Corrected

Sensible Cooling gures with our load requirements stated

in Step 1, we discover that our selection is within +/- 10%

of our sensible load requirement. Furthermore, we see that

our Corrected Total Cooling gure is slightly undersized as

recommended, when compared to the actual indicated load.

6

Heat Controller HRC SERIES Design Guide

HRC Series Nomenclature

*Requires extended unit - see cabinet dimensions.

7

Design Guide HRC SERIES Heat Controller

Performance Data – AHRI/ASHRAE/ISO 13256-1

Model

Water Loop Heat Pump Ground Water Heat Pump Ground Loop Heat Pump

Cooling 86°F Heating 68°F Cooling 59°F Heating 50°F Cooling 77°F Heating 32°F

Capacity

Btuh

EER

Btuh/W

Capacity

Btuh

COP

Capacity

Btuh

EER

Btuh/W

Capacity

Btuh

COP

Capacity

Btuh

EER

Btuh/W

Capacity

Btuh

COP

HRC09

8,600 13.3 11,400 4.6 9,200 18.6 9,500 4.0 8,800 14.9 7,300 3.3

HRC12

11,300 12.8 14,100 4.5 12,500 18.7 11,800 3.9 11,800 14.5 9,300 3.3

HRC15

13,700 12.8 17,500 5.1 15,700 19.4 14,600 4.0 14,500 14.7 11,400 3.3

HRC18

15,600 12.2 20,100 4.5 17,200 17.9 16,500 3.9 16,100 13.8 13,200 3.3

Cooling capacities based upon 80.6°F DB, 66.2°F WB entering air temperature

Heating capacities based upon 68°F DB, 59°F WB entering air temperature

All air ow is rated on high speed, Units factory shipped on medium and low motor taps.

All ratings based upon operation at lower voltage of dual voltage rated models

ASHRAE/AHRI/ISO 13256-1. English (I-P) Units

Model

Water Loop Heat Pump Ground Water Heat Pump Ground Loop Heat Pump

Cooling 30°C Heating 20°C Cooling 15°C Heating 10°C Cooling 25°C Heating 0°C

Capacity

kW

EER

W/W

Capacity

kW

COP

Capacity

kW

EER

W/W

Capacity

kW

COP

Capacity

kW

EER

W/W

Capacity

kW

COP

HRC09

2.52 3.9 3.34 4.6 2.70 5.5 2.78 4.0 2.58 4.4 2.14 3.3

HRC12

3.31 3.8 4.13 4.5 3.66 5.5 3.46 3.9 3.46 4.3 2.73 3.3

HRC15

4.02 3.8 5.13 5.1 4.60 5.7 4.28 4.0 4.25 4.3 3.34 3.3

HRC18

4.57 3.6 5.89 4.5 5.04 5.3 4.84 3.9 4.72 4.0 3.87 3.3

Cooling capacities based upon 27°C DB, 19°C WB entering air temperature

Heating capacities based upon 20°C DB, 15°C WB entering air temperature

All air ow is rated on high speed, Units factory shipped on medium and low motor taps.

All ratings based upon operation at lower voltage of dual voltage rated models

ASHRAE/AHRI/ISO 13256-1. Metric (S-I) Units

8

Heat Controller HRC SERIES Design Guide

Performance Data – Selection Notes

For operation in the shaded area when water is used in lieu of

an antifreeze solution, the LWT (Leaving Water Temperature)

must be calculated. Flow must be maintained to a level such

that the LWT is maintained above 42°F [5.6°C] when the

JW3 jumper is not clipped (see example below). Otherwise,

appropriate levels of a proper antifreeze solution should be

used in systems with leaving water temperatures of 42ºF

[5.6°C] or below and the JW3 jumper should be clipped. This

is due to the potential of the refrigerant temperature being as

low as 32°F [0°C] with 40°F [4.4°C] LWT, which may lead to a

nuisance cutout due to the activation of the Low Temperature

Protection. JW3 should never be clipped for standard range

equipment or systems without antifreeze.

Example:

At 50°F EWT (Entering Water Temperature) and 1.5 gpm/ton, a

3 ton unit has a HE of 22,500 Btuh. To calculate LWT, rearrange

the formula for HE as follows:

HE = TD x GPM x 500, where HE = Heat of Extraction (Btuh);

TD = temperature difference (EWT - LWT) and GPM = U.S.

Gallons per Minute.

TD = HE / (GPM x 500)

TD = 22,500 / (4.5 x 500)

TD = 10°F

LWT = EWT - TD

LWT = 50 - 10 = 40°F

In this example, a higher ow rate will be required for EWTs at or below 50°F without antifreeze. At 2 gpm/ton, the calculation

above results in a TD of 7.5. LWT = 50 - 7.5 = 42.5°F, which is above 42°F EWT, and is acceptable for this application.

EWT

°F

GPM

WPD* Cooling - EAT 80/67°F Heating - EAT 70°F

PSI FT TC SC

Sens/Tot

Ratio

kW HR EER HC kW HE LAT COP

20

1.9 3.7 8.5

Operation Not Recommended

5.5 0.50 3.8 91.0 3.22

30

1.0 1.4 3.2 9.7 6.9 0.71 0.36 10.9 26.7 6.0 0.51 4.3 93.1 3.44

1.4 2.2 5.1 9.8 6.9 0.70 0.33 10.9 29.9 6.3 0.52 4.5 94.1 3.55

1.9 3.3 7.6 9.9 6.9 0.70 0.31 10.9 31.7 6.4 0.52 4.7 94.8 3.62

40

1.0 1.0 2.3 9.4 6.8 0.72 0.41 10.8 22.9 6.9 0.53 5.1 96.5 3.79

1.4 1.5 3.5 9.6 6.9 0.71 0.37 10.9 25.8 7.2 0.54 5.4 97.9 3.91

1.9 2.1 4.9 9.7 6.9 0.71 0.36 10.9 27.4 7.4 0.55 5.6 98.6 3.97

50

1.0 0.9 2.1 9.0 6.7 0.74 0.46 10.6 19.6 7.8 0.56 5.9 100.0 4.10

1.4 1.4 3.2 9.3 6.8 0.73 0.42 10.8 22.1 8.2 0.57 6.3 101.6 4.23

1.9 2.0 4.6 9.5 6.8 0.72 0.40 10.8 23.4 8.4 0.57 6.5 102.4 4.30

60

1.0 0.8 1.8 8.6 6.5 0.76 0.52 10.4 16.6 8.7 0.58 6.7 103.6 4.39

1.4 1.3 3.0 8.9 6.6 0.74 0.48 10.5 18.8 9.2 0.59 7.2 105.4 4.53

1.9 1.9 4.4 9.1 6.7 0.74 0.46 10.6 20.0 9.4 0.60 7.4 106.3 4.61

70

1.0 0.7 1.6 8.1 6.3 0.78 0.58 10.1 14.0 9.6 0.61 7.6 107.1 4.67

1.4 1.2 2.8 8.5 6.5 0.76 0.53 10.3 15.9 10.2 0.62 8.1 109.1 4.82

1.9 1.8 4.2 8.6 6.5 0.76 0.51 10.4 16.9 10.5 0.63 8.3 110.2 4.90

80

1.0 0.7 1.6 7.6 6.1 0.79 0.65 9.8 11.8 10.6 0.63 8.4 110.7 4.93

1.4 1.1 2.5 8.0 6.2 0.78 0.60 10.0 13.3 11.1 0.64 9.0 112.9 5.10

1.9 1.6 3.7 8.1 6.3 0.78 0.57 10.1 14.2 11.5 0.65 9.3 114.1 5.19

85

1.0 0.6 1.4 7.4 5.9 0.80 0.68 9.7 10.8 11.0 0.64 8.9 112.5 5.06

1.4 1.0 2.3 7.7 6.1 0.79 0.63 9.9 12.2 11.6 0.65 9.4 114.8 5.24

1.9 1.5 3.5 7.9 6.2 0.78 0.61 10.0 13.0 12.0 0.66 9.7 116.1 5.33

90

1.0 0.6 1.4 7.2 5.8 0.81 0.72 9.6 9.9 11.5 0.65 9.3 114.2 5.19

1.4 1.0 2.3 7.5 6.0 0.80 0.67 9.8 11.1 12.1 0.66 9.9 116.7 5.38

1.9 1.4 3.2 7.6 6.1 0.79 0.64 9.8 11.9 12.5 0.67 10.2 118.0 5.48

100

1.0 0.5 1.2 6.7 5.5 0.81 0.81 9.5 8.3

Operation Not Recommended

1.4 0.9 2.1 7.0 5.7 0.81 0.75 9.6 9.3

1.9 1.3 3.0 7.2 5.8 0.81

0.72 9.6 9.9

110

1.0 0.5 1.2 6.4 5.2 0.81 0.91 9.5 7.0

1.4 0.9 2.1 6.6 5.4 0.81 0.84 9.5 7.8

1.9 1.3 3.0 6.7 5.5 0.81 0.81 9.5 8.3

Interpolation is permissible; extrapolation is not.

All entering air conditions are 80°F DB and 67°F WB in cooling, and 70°F DB in heating. ARI/ISO certied conditions are 80.6°F DB and

66.2°F WB in cooling and 68°F DB in heating.

Table does not reect fan or pump power corrections for ARI/ISO conditions.

All performance is based upon the lower voltage of dual voltage rated units.

Operation below 40°F EWT is based upon a 15% antifreeze solution.

Operation below 60°F EWT requires optional insulated water/refrigerant circuit (standard on residential models).

See performance correction tables for operating conditions other than those listed above.

See Performance Data Selection Notes for operation in shaded areas.

9

Design Guide HRC SERIES Heat Controller

Performance Data – HRC09

EWT

°F

GPM

WPD* Cooling - EAT 80/67°F Heating - EAT 70°F

PSI FT TC SC

Sens/

Tot

Ratio

kW HR EER HC kW HE LAT COP

20

2.2 5.0 11.6

Operation not recommended

6.3 0.67 4.0 86.6 2.72

30

1.1 1.6 3.7 9.2 6.7 0.73 0.44 10.7 20.6 6.9 0.69 4.6 88.2 2.94

1.6 2.6 6.0 8.9 6.6 0.74 0.43 10.4 20.7 7.2 0.69 4.8 89.0 3.04

2.2 4.5 10.4 8.8 6.5 0.74 0.43 10.2 20.6 7.3 0.69 5.0 89.4 3.11

40

1.1 1.4 3.2 9.4 6.9 0.73 0.47 11.1 19.9 7.9 0.70 5.5 90.9 3.29

1.6 2.3 5.3 9.3 6.8 0.73 0.45 10.9 20.5 8.3 0.71 5.9 91.8 3.41

2.2 4.2 9.7 9.2 6.7 0.73 0.45 10.7 20.6 8.5 0.71 6.1 92.4 3.48

50

1.1 1.2 2.8 9.5 7.0 0.74 0.51 11.3 18.5 8.9 0.72 6.5 93.7 3.63

1.6 2.2 5.1 9.5 6.9 0.73 0.49 11.1 19.5 9.3 0.73 6.9 94.7 3.76

2.2 3.8 8.8 9.4 6.9 0.73 0.47 11.1 19.9 9.6 0.73 7.1 95.4 3.84

60

1.1 1.1 2.5 9.4 7.1 0.76 0.56 11.3 16.7 10.0 0.74 7.5 96.4 3.95

1.6 2.1 4.9 9.5 7.0 0.74 0.53 11.3 17.9 10.4 0.75 7.9 97.6 4.08

2.2 3.7 8.5 9.5 7.0 0.74 0.51 11.2 18.6 10.7 0.75 8.1 98.3 4.16

70

1.1 1.0 2.3 9.0 7.1 0.79 0.62 11.2 14.5 11.0 0.76 8.4 99.0 4.23

1.6 2.0 4.6 9.3 7.1 0.77 0.58 11.3 15.9 11.4 0.77 8.8 100.2 4.36

2.2 3.5 8.1 9.4 7.1 0.76 0.56 11.3 16.7 11.7 0.77 9.1 101.0 4.43

80

1.1 1.0 2.3 8.5 7.0 0.82 0.69 10.9 12.3 11.9 0.78 9.2 101.4 4.47

1.6 1.9 4.4 8.8 7.1 0.80 0.65 11.1 13.7 12.3 0.79 9.6 102.6 4.58

2.2 3.2 7.4 9.0 7.1 0.79 0.62 11.2 14.5 12.6 0.80 9.9 103.4 4.64

85

1.1 1.0 2.2 8.1 6.9 0.84 0.73 10.6 11.1 12.3 0.79 9.6 102.5 4.56

1.6 1.9 4.4 8.5 7.0 0.82 0.68 10.9 12.5 12.7 0.80 10.0 103.6 4.66

2.2 3.1 7.2 8.8 7.0 0.80 0.66 11.0 13.3 13.0 0.81 10.2 104.3 4.71

90

1.1 0.9 2.1 7.8 6.7 0.87 0.77 10.4 10.1 12.7 0.80 10.0 103.5 4.66

1.6 1.9 4.4 8.2 6.9 0.84 0.72 10.7 11.4 13.1 0.81 10.3 104.6 4.74

2.2 3.0 6.9 8.5 7.0 0.82 0.69 10.9 12.2 13.3 0.82 10.5 105.2 4.77

100

1.1 0.9 2.1 6.9 6.3 0.91 0.86 9.8 7.9

Operation not recommended

1.6 1.8 4.2 7.4 6.6 0.89 0.81 10.2 9.1

2.2 2.9 6.7 7.7 6.7

0.87 0.78 10.4 9.9

110

1.1 0.9 2.1 5.8 5.6 0.97 0.96 9.1 6.0

1.6 1.8 4.2 6.4 6.0 0.94 0.91 9.5 7.0

2.2 2.9 6.7 6.7 6.2 0.92 0.87 9.7 7.7

120

1.1 0.9 2.1 4.5 4.6 1.00 1.07 8.2 4.2

1.6 1.8 4.2 5.1 5.1 1.00 1.02 8.6 5.0

2.2 2.8 6.5 5.5 5.4 0.98 0.98 8.9 5.6

Interpolation is permissible; extrapolation is not.

All entering air conditions are 80°F DB and 67°F WB in cooling, and 70°F DB in heating.

AHRI/ISO certied conditions are 80.6°F DB and 66.2°F WB in cooling and 68°F DB in heating.

Table does not reect fan or pump power corrections for AHRI/ISO conditions.

All performance is based upon the lower voltage of dual voltage rated units.

Performance stated is at the rated power supply; performance may vary as the power supply varies from the rated.

Operation below 40°F EWT is based upon a 15% methanol antifreeze solution.

Operation below 60°F EWT requires optional insulated water/refrigerant circuit.

See performance correction tables for operating conditions other than those listed above.

See Performance Data Selection Notes for operation in the shaded areas.

Performance capacities shown in thousands of Btuh350 CFM Nominal (Rated) Airow

*WPD Adder for

Motorized Valve,

HRC09

(Cv = 4.9,

MOPD = 150 psi)

GPM

WPD Adder

PSI FT

1.1 0.3 0.6

1.6 0.6 1.3

2.2 1.2 2.7

10

Heat Controller HRC SERIES Design Guide

Performance Data – HRC12

Performance capacities shown in thousands of Btuh450 CFM Nominal (Rated) Airow

EWT

°F

GPM

WPD* Cooling - EAT 80/67°F Heating - EAT 70°F

PSI FT TC SC

Sens/

Tot

Ratio

kW HR EER HC kW HE LAT COP

20

3.0 7.8 18.0

Operation not recommended

7.3 0.79 4.7 85.1 2.71

30

1.5 2.1 4.9 12.6 8.2 0.65 0.56 14.5 22.4 8.1 0.81 5.4 86.7 2.96

2.3 4.5 10.4 12.4 8.0 0.65 0.53 14.2 23.3 8.5 0.81 5.7 87.5 3.06

3.0 6.8 15.7 12.3 8.0 0.65 0.52 14.0 23.6 8.7 0.82 5.9 87.9 3.12

40

1.5 2.0 4.6 12.7 8.4 0.67 0.61 14.7 20.7 9.4 0.83 6.7 89.4 3.35

2.3 4.2 9.7 12.6 8.2 0.65 0.58 14.6 21.9 9.9 0.83 7.1 90.4 3.48

3.0 6.1 14.1 12.6 8.2 0.65 0.56 14.5 22.4 10.2 0.84 7.3 90.9 3.56

50

1.5 1.8 4.2 12.5 8.7 0.70 0.67 14.8 18.7 10.8 0.85 8.0 92.3 3.74

2.3 3.8 8.8 12.6 8.5 0.68 0.63 14.8 20.0 11.4 0.86 8.5 93.5 3.91

3.0 5.8 13.4 12.7 8.4 0.67 0.61 14.7 20.7 11.7 0.86 8.8 94.1 4.00

60

1.5 1.7 3.9 12.1 9.0 0.74 0.73 14.6 16.6 12.2 0.87 9.3 95.1 4.14

2.3 3.7 8.5 12.4 8.8 0.71 0.69 14.7 17.9 12.9 0.87 9.9 96.5 4.32

3.0 5.2 12.0 12.5 8.7 0.70 0.67 14.8 18.6 13.2 0.88 10.2 97.2 4.41

70

1.5 1.5 3.5 11.6 9.2 0.79 0.80 14.4 14.5 13.6 0.88 10.6 97.9 4.50

2.3 3.5 8.1 12.0 9.1 0.76 0.76 14.5 15.8 14.3 0.89 11.2 99.4 4.69

3.0 4.9 11.3 12.1 9.0 0.74 0.73 14.6 16.5 14.6 0.90 11.6 100.1 4.79

80

1.5 1.4 3.2 11.0 9.2 0.83 0.89 14.1 12.5 14.8 0.90 11.8 100.5 4.84

2.3 3.2 7.4 11.4 9.2 0.81 0.83 14.3 13.7 15.5 0.91 12.4 101.9 5.01

3.0 4.8 11.1 11.6 9.2 0.79 0.81 14.4 14.4 15.8 0.91 12.7 102.6 5.10

85

1.5 1.4 3.1 10.7 9.1 0.85 0.93 13.9 11.5 15.4 0.90 12.3 101.6 4.98

2.3 3.1 7.2 11.1 9.2 0.83 0.88 14.1 12.7 16.0 0.91 12.9 102.9 5.13

3.0 4.7 10.7 11.3 9.2 0.81 0.85 14.2 13.4 16.3 0.92 13.1 103.5 5.20

90

1.5 1.3 3.0 10.4 9.1 0.87 0.98 13.7 10.6 15.9 0.91 12.8 102.7 5.11

2.3 3.0 6.9 10.8 9.2 0.85 0.92 13.9 11.7 16.5 0.92 13.3 103.9 5.25

3.0 4.5 10.4 11.0 9.2 0.84 0.89 14.1 12.3 16.7 0.92 13.6 104.4 5.31

100

1.5 1.3 3.0 9.7 8.7 0.90 1.08 13.4 9.0

Operation not recommended

2.3 2.9 6.7 10.1 9.0 0.88 1.02 13.6 9.9

3.0 4.3 9.9 10.3 9.0

0.88 0.99 13.7 10.5

110

1.5 1.2 2.8 9.0 8.2 0.91 1.20 13.1 7.5

2.3 2.9 6.7 9.4 8.5 0.90 1.13 13.3 8.4

3.0 4.2 9.7 9.6 8.7 0.90 1.09 13.4 8.8

120

1.5 1.2 2.8 8.4 7.5 0.89 1.33 12.9 6.3

2.3 2.8 6.5 8.7 7.9 0.91 1.25 13.0 7.0

3.0 4.1 9.5 8.9 8.1 0.91 1.21 13.1 7.4