Hunter Fan 97056 Owner's manual

42917-01 01/29/2008

1

Installation Guide

97055/97056/97057 Low Profile

™

Bath Ventilator with Light

READ and SAVE THESE INSTRUCTIONS

ENGLISH

See page 2

FRANçAIS

Consulter la page 23

030_42917_EngF_1.29.08_Arial.indd 1 1/29/08 12:15:09 AM

42917-01 01/29/2008

2

DISCONNECT ELECTRIC

POWER SUPPLY

AND LOCK OUT

SERVICE PANEL BEFORE

SERVICING UNIT

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

1. For general ventilating use only. Do not use to exhaust hazard-

ous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy/unbalanced impellers,

keep drywall spray, construction dust, etc. off power unit.

3. DO NOT install this product in a wall. This product is designed

for installation in ceilings up to a 12/12 pitch (45 degrees).

Ductwork must point upward.

4. Pleasereadspecicationlabelonproductforfurtherinformation

and requirements.

PREVENTATIVE MAINTENANCE

A clean fan provides better service. Disconnect the power supply and

clean the fan as listed below.

TO CLEAN GRILLE: Use a mild detergent, such as dishwashing

liquid, and a soft cloth. DO NOT use abrasive cloths, steel wool pads

or scouring powders.

TO CLEAN FAN ASSEMBLY: Unplug motor cord from receptacle.

To remove motor plate, find the single tab on the motor plate (located

next to the receptacle). Push up rear motor plate tab while pushing

out on the side of the housing or insert a screwdriver into the slot in

the housing (next to tab) and twist screwdriver. Gently vacuum fan,

motor and interior of housing.

METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED

IN WATER.

MAINTENANCE

The motor is permanently lubricated and never needs oiling. If the

motor bearings are making excessive or unusual noises, replace the

motor with the exact service motor. You should replace the impeller at

the same time.

CAUTION

WARNING

1. Use this unit only in a manner intended by the manufacturer.

If you have questions, contact the manufacturer.

2. Before servicing or cleaning the unit, switch power off at ser-

vice panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by quali-

edperson(s)inaccordancewithallapplicablecodesand

standards,includingre-ratedconstruction.

4. Sufcientairisneededforpropercombustionandexhausting

ofgassesthroughtheue(chimney)offuelburningequipment

to prevent backdrafting. Follow the heating equipment manufac-

turer’s guideline and safety standards,such as those published

by the National Fire Prevention Association (NFPA), and the

American Society for Heating, Refrigeration and Air-Conditioning

Engineers (ASHRAE), and the local code authorities.

5. When cutting or drilling into wall(s) or ceiling, do not damage

electrical wiring or other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. If this unit is to be installed over a tub or shower, it must be

marked as appropriate for the application and be connected to a

GFCI (Ground Fault Circuit Interrupter) – protected branch circuit.

8. Never place a switch where it can be reached from a tub or

shower.

9. Installfanatleast5feet(1.52m)abovetheoor.

10. This unit must be grounded.

11. Unit must not be installed in a ceiling thermally insulated to a

value greater than R40.

Do Not Install Above

Or Inside This Area

Cooking

Equipment

Floor

45° 45°

COOKING AREA

030_42917_EngF_1.29.08_Arial.indd 2 1/29/08 12:15:10 AM

42917-01 01/29/2008

3

D

E

F

G

H

I

L

M

N

95044-01-000

95029-01-000

75191-01-000

03242-07-133

95491-02-000

74508-03-133

95511-01/02/03-000

J

77521-01

K

65219

75184-01-133

94997-01/02/03-000

O

7517-01/02/03-000

x4

*

NOTE:

Strain relief cable

connector must be

installed. Not Included.

A

B

C

Extra Screws

x2

I

3/8” Cable Connector

x2

1

2

E

I

Turn off the power source.

Tools Needed.

Estimated assembly time: 30 to 60 minutes

Before Installation

Check all the parts.

If damaged, call

1-888-830-1326

for replacements.

Included.

Loosen screws.

NOTE: Remove all packing materials before installation.

030_42917_EngF_1.29.08_Arial.indd 3 1/29/08 12:15:12 AM

42917-01 01/29/2008

4

5

4

7

G

8

F

H

E

3

6

Remove the motor/blower from the housing.

Remove the pre-loaded screw tip covers.

Remove the wiring cover screw.

Back out the pre-loaded screw tips until flush

with the side of the housing.

Remove the wiring cover.

Remove packing material.

030_42917_EngF_1.29.08_Arial.indd 4 1/29/08 12:15:14 AM

42917-01 01/29/2008

5

9

E

10

B

C

A11

E

5/8

1/2

5/8

1/2

A12

Pop out the first wiring access slug. Use second if needed. Insert the strain relief into the housing and

secure with the washer.

Position the correct depth mark at the bottom edge of the

joist based on the thickness of your sheetrock.

New Construction – attaching to joist

Choose Installation Option

For New Construction - attaching to joist go to step A11, page 5

For New Construction - suspended between joists go to step B11, page 8

For Existing Construction - accessible from above go to step C11, page 11

For Existing Construction - accessible only from below go to step D11, page15

Screw pre-loaded screws into joist or framing.

030_42917_EngF_1.29.08_Arial.indd 5 1/29/08 12:15:16 AM

42917-01 01/29/2008

6

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

White

Black

White

Bare Copper

Ground

A14

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

A13

0

A16

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may need

to be purchased.

A15

E

F

G

Install the wiring cover plate. Make sure all

wiring connections are inside the box or under

the wiring cover plate.

Connect wires as shown.

Pull wires through the strain relief.

030_42917_EngF_1.29.08_Arial.indd 6 1/29/08 12:15:19 AM

42917-01 01/29/2008

7

A19

I

A20

Connect wiring from the motor to the wiring cover plate.

0000

A17

0000

H

A18

ON

OFF

A21

A22

E1

Go to step

on page 17

to attach grille.

Reinstall the motor by inserting the tabs and pushing up into

position. Make sure the wires are not pinched

between the motor and the housing.

Secure the motor by tightening the 2 screws.

Turn on the power source.

Test the motor. If the motor does not run,

check the plug connection.

030_42917_EngF_1.29.08_Arial.indd 7 1/29/08 12:15:22 AM

42917-01 01/29/2008

8

B11

D

E

5/8

1/2

5/8

1/2

B12

1/8" Bit

B14

B15

B16

E

B13

Slide the mounting rails into brackets.

Mark position of screws by using holes as a template.

Insert screws, leaving space between the screw

head and the joist. Screws are not provided.

New Construction – suspended between joists

Position the correct depth mark at the bottom edge of

the joist based on the thickness of your sheetrock.

Drill a hole in the center of each outline.

Attach the rails onto the screws.

030_42917_EngF_1.29.08_Arial.indd 8 1/29/08 12:15:25 AM

42917-01 01/29/2008

9

B17

B18

Connect wires as shown.

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

White

Black

White

Bare Copper

Ground

B19

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

B21

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may need

to be purchased.

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under the

wiring cover plate.

F

G

B20

Tighten screws. Pull wires through the strain relief.

030_42917_EngF_1.29.08_Arial.indd 9 1/29/08 12:15:28 AM

42917-01 01/29/2008

10

B27

E1

Go to step

on page 17

to attach grille.

B22

H

Connect wiring from the motor to the wiring cover plate.

H

B23

Reinstall the motor by inserting the tabs and pushing up into

position. Make sure the wires are not pinched

between the motor and the housing.

B25

Turn on the power source.

ON

OFF

B26

Test the motor. If the motor does not run,

check the plug connection.

B24

I

Secure the motor by tightening the 2 screws.

030_42917_EngF_1.29.08_Arial.indd 10 1/29/08 12:15:32 AM

42917-01 01/29/2008

11

C12

D

E

EXISTING FAN

C11

NO EXISTING FAN

8”

8.5”

5/8

1/2

5/8

1/2

C13

C14

Existing Construction – accessible from above

OR

Cut out an opening for the housing. Slide the mounting rails into brackets.

Position the correct depth mark at the bottom edge of the

joist based on the thickness of your sheetrock.

Mark position of screws by using holes as a template.

Remove an existing fan and check to make sure the

opening is large enough to accommodate the new

motor housing (8”x 8.5”).

Use the motor housing as a template to mark position.

030_42917_EngF_1.29.08_Arial.indd 11 1/29/08 12:15:35 AM

42917-01 01/29/2008

12

C15

1/8" Bit

C16

C17

C18

C19

C20

Drill a hole in the center of each outline. Insert screws, leaving space between the screw head

and the joist. Screws are not provided.

Attach the rails onto the screws. Tighten screws.

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may

need to be purchased.

Pull wires through the strain relief.

030_42917_EngF_1.29.08_Arial.indd 12 1/29/08 12:15:38 AM

42917-01 01/29/2008

13

C21

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

White

Black

White

Bare Copper

Ground

C22

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

C24

H

G

F

C23

Tighten the strain relief screws.

Connect wires as shown.

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under the

wiring cover plate.

Connect wiring from motor the motor

to the wiring cover plate.

030_42917_EngF_1.29.08_Arial.indd 13 1/29/08 12:15:40 AM

42917-01 01/29/2008

14

C25

H

C26

I

C27

ON

OFF

C28

C29

E1

Go to step

on page 17

to attach grille.

Secure the motor by tightening the 2 screws.

Turn on the power source.

Test the motor. If the motor does not run,

check the plug connection.

Reinstall the motor by inserting the tabs and pushing up into

position. Make sure the wires are not pinched

between the motor and the housing.

030_42917_EngF_1.29.08_Arial.indd 14 1/29/08 12:15:43 AM

42917-01 01/29/2008

15

EXISTING FAN

D11

E

D12

D13

2

1

D14

E

D15

Existing Construction – accessible only from below

Pull wires through strain relief.

Remove an existing fan and check to make sure the

opening is large enough to accommodate the new motor

housing (8”x 8.5”).

Move the housing into position above the ceiling.

Attach existing ducting to duct connector. Tape joints.

If ducting does not fit securely,

an adapter may need to be purchased.

Install the housing flush with the sheetrock and secure by

tightening the pre-loaded screws into the joist.

030_42917_EngF_1.29.08_Arial.indd 15 1/29/08 12:15:45 AM

42917-01 01/29/2008

16

H

D18

H

D19

D20

I

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

White

Black

White

Bare Copper

Ground

D16

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

F

D17

G

Reinstall the motor by inserting the tabs and pushing up into

position. Make sure the wires are not pinched between the

motor and the housing.

Connect wiring from the motor to the wiring cover plate.

Secure the motor by tightening the 2 screws.

Connect wires as shown.

Install the wiring cover plate.

030_42917_EngF_1.29.08_Arial.indd 16 1/29/08 12:15:48 AM

42917-01 01/29/2008

17

ON

OFF

D22

D23

E1

Go to step

on page 17

to attach grille.

D21

E2

O

L

N

M

E1

Test the motor. If the motor does not run,

check the plug connection.

Turn on the power source.

Attaching the Grille

Remove the thumbscrews.

Remove glass dome.

030_42917_EngF_1.29.08_Arial.indd 17 1/29/08 12:15:51 AM

42917-01 01/29/2008

18

E4

K

E5

J

E6

L

E3

Remove the strain relief bracket screw.

Position the strain relief bracket under the motor as shown. Insert the strain relief bracket’s dog-leg tab so that

it hooks over the lip of the motor. Reinstall the

strain relief bracket screw.

Connect wiring harness.

E7

L

M

E8

Align posts A, B, C and D (stamped into motor housing)

with posts A, B, C and D (stamped into light fixture).

Slide light fixture over posts.

Attach thumbscrews.

WARNING: To reduce the risk of electrical shock,

all 4 thumbscrews MUST be properly installed.

030_42917_EngF_1.29.08_Arial.indd 18 1/29/08 12:15:55 AM

42917-01 01/29/2008

19

E9

E10

N

O

E11

Install 2 Max 60 Watt A15 bulbs (Not Included).

Screw glass dome into position.

Align glass dome and push up.

030_42917_EngF_1.29.08_Arial.indd 19 1/29/08 12:15:57 AM

42917-01 01/29/2008

20

Trouble Shooting

Problem: Fan does not come on.

Solution:

 •HunterFanBathVentilatorsareextremelyquiet.Toconrmthatthefanisrunning,placeyourhandneartheventstofeel

the air movement.

 •Turnpoweron,replacefuse,orresetbreaker.

 •Checkallplugconnectionstobesuretheyaresecure.

 •Checkthewiringtomakesureitmatchesthewiringdiagram.

Problem: Light does not come on.

Solution:

 •Replacethelightbulbwithanewbulb.

 •Turnpoweron,replacefuse,orresetbreaker.

 •Checkallplugconnectionstobesuretheyaresecure.

 •Checkthewiringtomakesureitmatchesthewiringdiagram.

Problem: Fan is noisy.

Solution:

 •Checkandtightenallfasteners.

 •Checktheglasstomakesureitissecure.

 •Checktheappertomakesureitmovesfreely.

If you need parts or service assistance, please call 888-830-1326 or visit us at our WEB site at http://www.hunterfan.com.

030_42917_EngF_1.29.08_Arial.indd 20 1/29/08 12:15:57 AM

Page is loading ...

Hunter Fan 97056 Owner's manual

Hunter Fan 97056 Owner's manual

in other languages

Related papers

Other documents