2. Marshall Electronics
  3. CV-RCP-100
CV-RCP-100

Marshall Electronics CV-RCP-100 Quick start guide

  • Hello! I am an AI chatbot trained to assist you with the Marshall Electronics CV-RCP-100 Quick start guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • How do I connect the CV-RCP-100 to my camera?
    How do I control a specific camera with the CV-RCP-100?
    Can I control multiple cameras with the CV-RCP-100?
    How do I access the OSD menu on the CV-RCP-100?
    What is the power requirement for the CV-RCP-100?
    What are the operating temperature limits for the CV-RCP-100?
    What is the size of the CV-RCP-100?
1.7” (43mm)
. . . . .
. . . .
I
I
DC power
connector
Remote
connector to
camera
D-sub 9
Se ng adjustment knobs
I
4.2” (107mm)
5.7” (145mm)
I I
Touch
Screen
USB port
I
Serial
selector
switch
I
ç }
ã
Marshall
CV-RCP-100
Quick Start Guide
Touchscreen RCP Camera Control
1. Operating Instructions
2. Specifications
3. Dimensions
4. Inputs / Outputs
5. Serial I/O
1) Plug into 12V power supply contained in box or other 9-26V power
source (1.0 Amp Max)
2) Obtain a standard 3 Pin XLR cable and connect +/- to appropriate camera
phoenix connector, as illustrated below (ground not used on RS485)
3) If RCP does not connect and communicate with camera; switch the +/- wires on
camera side and check Camera ID# assigned in Camera OSD Menu under
MENU > DISPLAY CONTROL > CAM ID (#).
4) On RCP touchscreen hold down Camera ID# 1 (upper left on touchscreen),
on sub-menu select CAMERA MODEL and Camera ID# to control that camera.
5) Make Sure to set each Camera with appropriate Camera ID# to match
RCP unit or all to one Camera ID# for Global (all camera) adjustments.
6) Repeat Step 4/5 to add more cameras, but hold down position 2, 3, 4,
5, 6, 7 to correspond to camera ID# in group (up to 7 per RCP).
7) Use touch screen & dials for command adjustmens or pull up OSD
Menu by going to Adv Menu and push On Screen Menu.
8) Push “?” for further explanation of buttons or additional information.
9) Call 800-800-6608 for additional help and questions
(W x H x D, excluding projections)
4.2” x 5.7” x 1.7” (1
07mm x 145mm x 43mm)
Remote: 3-pin XLR Female
AUX: D-sub 9 (future accessories)
USB: For firmware updates
DC Input: 2.1 mm coaxial power connector
Connect Pin
#2 to CV camera
RS485 (phoenix) input (-) negative
Pin#1 is Ground (not used
on RS485 installation)
Connect Pin
#3 to CV
camera RS485 (phoenix)
input labeled (+) positive
RS-485 Mode
Slide switch under cap on left side to RS-485 position
XLR pin 2 - RS-485A
XLR pin 3 - RS-485B
RS-232 Mode
Slide switch under cap on left side to RS-232 position
XLR pin 1 - Ground
XLR pin 2 - Tx
XLR pin 3 - Rx
Rev. 4 /0
9/22/2016
Power:
Operating Temp:
Weight:
9 V DC - 26 V DC, 1.0 A (Max.)
-4 °F to 158 °F (-20 °C to 70 °C)
Marshall Electronics
/