H3C H3C S5100-SI Series Quick start guide

Category
Network switches
Type
Quick start guide

This manual is also suitable for

H3C S5100-SI/EI Series
Ethernet Switches
Quick Start
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version: T2-08018B-20070522-C-1.02
Copyright © 2007, Hangzhou H3C Technologies Co., Ltd.
and its licensors
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form
or by any means without prior written consent of Hangzhou H3C
Technologies Co., Ltd.
Trademarks
H3C, , Aolynk, , H
3
Care,
, TOP G, , IRF,
NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath,
Comware, Secware, Storware, NQA, VVG, V
2
G, V
n
G, PSPT, XGbus,
N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou
H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the
property of their respective owners.
Notice
The information in this document is subject to change without notice.
Every effort has been made in the preparation of this document to
ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of
any kind, express or implied.
To obtain the latest information, please access:
http://www.h3c.com
Technical Support
customer_service@h3c.com
http://www.h3c.com
About This Manual
Related Documentation
In addition to this manual, each H3C S5100-SI/EI Series Ethernet
Switches documentation set includes the following:
Manual Content
H3C S5100-SI/EI Series
Ethernet Switches Operation
Manual
It is used for assisting the users
in data configurations and
typical applications
H3C S5100-SI/EI Series
Ethernet Switches Command
Manua
It is used for assisting the users
in using various commands.
H3C S5100-SI/EI Series
Ethernet Switches Installation
Manual
It is used for assisting the users
in switch installation, booting up,
hardware and software
maintenance.
Organization
H3C S5100-SI/EI Series Ethernet Switches Quick Start is
organized as follows:
Chapter Contents
1 Product Overview
Introduces the characteristics and
technical specifications of S5100-SI/EI
Series Ethernet Switches.
Chapter Contents
2 Preparing for
Installation
Introduces the installation preparation and
precaution of S5100-SI/EI Series Ethernet
Switches.
3 Installing the Switch
Introduces the procedures to install an
S5100-SI/EI Series Ethernet Switch,
including the setup of the mainframe,
cards and cables.
4 Lightning Protection
of the Switch
Introduces lightning protection of
S5100-SI/EI Series Ethernet Switches.
Conventions
The manual uses the following conventions:
I.
GUI conventions
Convention Description
< >
Button names are inside angle brackets.
For example, click <OK>.
[ ]
Window names, menu items, data table
and field names are inside square
brackets. For example, pop up the [New
User] window.
/
Multi-level menus are separated by forward
slashes. For example, [File/Create/Folder].
Symbols II.
Convention Description
Warning
Means reader be extremely careful.
Improper operation may cause bodily
injury.
Caution
Means reader be careful. Improper
operation may cause data loss or damage
to equipment.
Note Means a complementary description.
Environmental Protection
This product has been designed to comply with the requirements
on environmental protection. For the proper storage, use and disposal
of this product, national laws and regulations must be observed.
Quick Start
H3C S5100-SI/EI Series Ethernet Switches Table of Contents
i
Table of Contents
Chapter 1 Product Overview ........................................................1-1
1.1 Preface...............................................................................1-1
1.2 LEDs ..................................................................................1-4
1.3 System Features of the S5100 Series ...............................1-8
1.3.1 System Features of the S5100-SI Series................1-8
1.3.2 System Features of the S5100-EI Series................1-9
1.4 Ordering SFP Interface Modules .....................................1-16
1.5 Ordering 10 G Stack Interface Modules ..........................1-18
1.6 Ordering Stack Cables.....................................................1-18
1.7 Ordering DC Power cords................................................1-19
Chapter 2 Preparing for Installation ............................................2-1
2.1 Safety Precautions.............................................................2-1
2.2 Installation Site...................................................................2-1
2.2.1 Temperature/Humidity.............................................2-2
2.2.2 Cleanness................................................................2-3
2.2.3 Electromagnetic Susceptibility.................................2-4
2.2.4 Safety in Use of Laser .............................................2-4
2.3 Installation Tools ................................................................2-5
Chapter 3 Installing the Switch....................................................3-1
3.1 Rack-Mounting the Switch .................................................3-1
3.1.1 Introduction to Mounting Ear ...................................3-3
3.1.2 Introduction to Guide Rail........................................3-6
3.1.3 Using Front Mounting Ears to Install a Switch ........3-6
Quick Start
H3C S5100-SI/EI Series Ethernet Switches Table of Contents
ii
3.1.4 Use Front Mounting Ears and a Tray ......................3-8
3.1.5 Use Front and Rear Mounting Ears.........................3-9
3.1.6 Use Front Mounting Ears and Guide Rails............3-13
3.2 Desk Mounting .................................................................3-16
3.3 Wall Mounting ..................................................................3-17
3.4 Magnet Mounting .............................................................3-20
3.5 Connecting Power Cord and Grounding Wire .................3-23
3.5.1 Connecting AC Power Cord ..................................3-23
3.5.2 Connecting DC Power Cord..................................3-25
3.5.3 Connecting Grounding Wire ..................................3-27
3.6 Connecting Console Cable ..............................................3-32
3.6.1 Console Cable.......................................................3-32
3.6.2 Connecting Console Cable....................................3-33
3.7 Installing and Removing Optional Interface Modules ......3-35
3.7.1 XFP Interface Module............................................3-35
3.7.2 Stack Module.........................................................3-38
3.7.3 XENPAK Optical Module.......................................3-39
3.8 Installing and Removing Dedicated Stack Cables ...........3-42
3.8.1 Introduction............................................................3-42
3.8.2 Installation .............................................................3-43
3.8.3 Removal ................................................................3-43
3.9 Verifying the Installation...................................................3-44
Chapter 4 Lightning Protection of the Switch............................4-1
4.1 Installation of Lightning Arrester for AC Power (Socket Strip
with Lightning Protection).........................................................4-1
Quick Start
H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview
1-1
Chapter 1 Product Overview
1.1 Preface
H3C S5100 Series Ethernet Switches (hereinafter referred to as
the H3C S5100 series) are Gigabit Ethernet switching products
developed by H3C Technology Co., Ltd. The H3C S5100 series
provide a variety of service features. The H3C S5100 series are
designed as convergence and access devices for intranets and
metropolitan area networks (MANs), and can also be used for
connecting data center server clusters.
The H3C S5100 series come in two series: S5100-SI and
S5100-EI, which are available in the models listed in
Table 1-1:
An SFP port and its corresponding 10/100/1000Base-T
autosensing Ethernet port form a Combo port. That is, only one of the
two ports forming the Combo port can be used at a time.
Table 1-2
shows the mapping relations between the ports forming the Combo
port.
Quick Start
H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview
1-2
Table 1-1 H3C S5100-SI/EI series
Series Model
10/100/1
000Base
-T
autosen
sing
Ethernet
port
1000Base-
X SFP port
Console
port
S5100-8P-SI 8 2
S5100-16P-SI 16
S5100-24P-SI 24
S5100-S
I
S5100-48P-SI 48
4
S5100-8P-EI 8 2
S5100-16P-EI 16
S5100-24P-EI 24
S5100-48P-EI 48
S5100-26C-EI 24
S5100-50C-EI 48
4
S5100-8P-PWR
-EI
8 2
S5100-16P-PW
R-EI
16
S5100-26C-PW
R-EI
24
S5100-E
I
S5100-50C-PW
R-EI
48
4
1
Quick Start
H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview
1-3
Table 1-2 Mapping relations between the ports forming the
Combo port
Model
1000Base-X
SFP port
10/100/1000Base-T
autosensing
Ethernet port
17 14
18 16
19 13
S5100-16P-SI
S5100-16P-EI
S5100-16P-PWR-EI
20 15
25 22
26 24
27 21
S5100-24P-SI
S5100-24P-EI
S5100-26C-EI
S5100-26C-PWR-EI
28 23
49 46
50 48
51 45
S5100-48P-SI
S5100-48P-EI
S5100-50C-EI
S5100-50C-PWR-EI
52 47
Quick Start
H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview
1-4
1.2 LEDs
Note:
z For the descriptions on the Ethernet port status LEDs and Ethernet
port mode LEDs (MODE) of the S5100 series, see H3C
S5100-SI/EI Series Ethernet Switches Installation Manual.
z Only the S5100-24P-EI, S5100-48P-EI, S5100-26C-EI,
S5100-50C-EI, S5100-26C-PWR-EI, and S5100-50C-PWR-EI
Ethernet switches provide DC power LEDs.
z Only the S5100-26C-EI, S5100-50C-EI, S5100-26C-PWR-EI, and
S5100-50C-PWR-EI Ethernet switches provide module LEDs.
Quick Start
H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview
1-5
Table 1-3 Description on the LEDs of the S5100-SI/EI series
LED Mark Status Description
Yellow, ON The switch is starting.
Green, ON
The switch has been normally
started.
Green, blinking
(1 Hz)
The system is performing
POST (power-on self test) or
downloading software.
Read, ON
The system POST has failed or
another fatal error has been
detected.
Yellow, blinking
(1 Hz)
One or more ports have failed
in POST or other non-fatal
errors have been detected.
Power
LED
PWR
OFF
The switch has been powered
off.
Green, ON
Both AC and DC inputs are
normal.
Yellow, ON
The AC input is abnormal; the
DC input is normal.
DC
power
supply
LED
RPS
OFF There is no DC input.
Quick Start
H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview
1-6
LED Mark Status Description
OFF
The module has not been
installed or connected.
Green, ON
The module has been installed
and connected.
Green, blinking
The module is receiving or
sending data.
Yellow, blinking
(3 Hz)
Module POST has failed.
Modul
e LED
MOD
1 (or
MOD
2)
Yellow, ON
The device does not support
this module.
POST
runni
ng
Green,
blinkin
g
The POST ID of the in-process
test is displayed.
POST
failed
Red,
ON
The POST ID of the failed test
blinks.
Loadi
ng
softw
are
Green,
blinkin
g
A light bar rotates clockwise
around the display during the
downloading procedure.
7-seg
ment
digitro
n
displa
y
Unit
Fan
failure
Red,
ON
An “F” is displayed.
Quick Start
H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview
1-7
LED Mark Status Description
A “1” is displayed.
Unit
ID
Green,
ON
A “C” is displayed on command
switch.
Clust
er
mana
geme
nt
Green,
ON
An “S” is displayed on member
switch.
A “c” is displayed on candidate
switch.
An “I” is displayed on
independent switch.
Over-
temp
eratur
e
alarm
The digitron display shows a
"t".
Red,
ON
PoE
status
(for
the
S510
0-EI
series
only)
The ratio of the power used by
the port for PoE to the total
available power is displayed.
Green,
ON
0 - 20%
21 - 40%
41 - 60%
61 - 80%
81 - 100%
Quick Start
H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview
1-8
1.3 System Features of the S5100 Series
1.3.1 System Features of the S5100-SI Series
Table 1-4 System features of the S5100-SI series
Item
S5100-8P-S
I
S5100-16P-
SI
S5100-24
P-SI
S5100-48P-
SI
Dimensi
ons
(H × W
× D)
43.6 × 230 ×
200 mm (1.7
× 9.1 × 7.9
in.)
43.6 × 300 ×
220 mm (1.7
× 11.8 × 8.7
in.)
43.6 × 440 × 260 mm
(1.7 × 17.3 × 10.2 in.)
Weight
< 1.6 kg (<
3.5 lb.)
< 2.3 kg (<
5.1 lb.)
< 4 kg (<
8.8 lb.)
4 kg (8.8 lb.)
Service
ports
8 ×
10/100/1000
Base-T
autosensing
Ethernet
ports
2 ×
1000Base-X
SFP ports
16 ×
10/100/1000
Base-T
autosensing
Ethernet
ports
4 Gigabit
SFP Combo
ports
24 ×
10/100/1
000
Base-T
autosensi
ng
Ethernet
ports
4 Gigabit
SFP
Combo
ports
48 ×
10/100/1000
Base-T
autosensing
Ethernet
ports
4 Gigabit
SFP Combo
ports
Manage
ment
port
One console port
Power
supply
system
The S5100-SI series support AC power input.
Rated voltage range: 100 VAC to 240 VAC, 50 Hz or
60Hz
Max voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
Quick Start
H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview
1-9
Item
S5100-8P-S
I
S5100-16P-
SI
S5100-24
P-SI
S5100-48P-
SI
Max
power
consum
ption
16 W 25 W 39 W 78 W
Fan 1 1 1 2
Operati
ng
tempera
ture
0°C to 45°C (32°F to 113°F)
Relative
humidit
y
(noncon
densing
)
10% to 90%
1.3.2 System Features of the S5100-EI Series
Table 1-5 System features of the S5100-EI series (1)
Item
S5100-8P-
EI
S5100-16P-
EI
S5100-24
P-EI
S5100-48
P-EI
Dimensio
ns
(H × W ×
D)
43.6 × 230
× 200 mm
(1.7 × 9.1 ×
7.9 in.)
43.6 × 300 ×
220 mm (1.7
× 11.8 × 8.7
in.)
43.6 × 440 × 260 mm
(1.7 × 17.3 × 10.2 in.)
Weight
< 1.6 kg (<
3.5 lb.)
< 2.3 kg (<
5.1 lb.)
< 4 kg (<
8.8 lb.)
4 kg (8.8
lb.)
Quick Start
H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview
1-10
Item
S5100-8P-
EI
S5100-16P-
EI
S5100-24
P-EI
S5100-48
P-EI
Service
ports
8 ×
10/100/100
0Base-T
autosensin
g Ethernet
ports
2 ×
1000Base-
X SFP ports
16 ×
10/100/1000
Base-T
autosensing
Ethernet
ports
4 Gigabit
SFP Combo
ports
24 ×
10/100/10
00Base-T
autosensin
g Ethernet
ports
4 Gigabit
SFP
Combo
ports
48 ×
10/100/10
00Base-T
autosensin
g Ethernet
ports
4 Gigabit
SFP
Combo
ports
Managem
ent port
One console port
Power
supply
system
The S5100-EI series support AC input and DC input.
AC input:
Rated voltage range: 100 VAC to 240 VAC, 50 Hz or
60Hz
Max voltage range: 90 VAC to 264 VAC, 47 Hz to 63
Hz
DC input (for the S5100-24P-EI and S5100-48P-EI):
Rated voltage range: -48 VDC to -60 VDC
Max voltage range:-36 VDC to -72 VDC
Max
power
consumpt
ion
18 W 26 W 46 W 97 W
Fan 1 1 1 2
Operating
temperatu
re
0°C to 45°C (32°F to 113°F)
Quick Start
H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview
1-11
Item
S5100-8P-
EI
S5100-16P-
EI
S5100-24
P-EI
S5100-48
P-EI
Relative
humidity
(noncond
ensing)
10% to 90%
Table 1-6 System features of the S5100-EI series (2)
Item S5100-26C-EI S5100-50C-EI
Dimensio
ns
(H × W ×
D)
43.6 × 440 × 300 mm (1.7 × 17.3 × 11.8 in.)
Weight 4 kg (8.8 lb.) < 5 kg (< 11 lb.)
Service
ports
24 ×
10/100/1000MBase-T
autosensing Ethernet
ports
4 Gigabit SFP Combo
ports
48 ×
10/100/1000MBase-T
autosensing Ethernet
ports
4 Gigabit SFP Combo
ports
Extension
slots
Two 10 G slots Two 10 G slots
Managem
ent port
One console port
Quick Start
H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview
1-12
Item S5100-26C-EI S5100-50C-EI
Power
supply
system
The S5100-EI series support AC input and DC input.
AC input:
Rated voltage range: 100 VAC to 240 VAC, 50 Hz or
60Hz
Max voltage range: 90 VAC to 264 VAC, 47 Hz to 63
Hz
DC input:
Rated voltage range: -48 VDC to -60 VDC
Max voltage range: -36 VDC to -72 VDC
Max
power
consumpti
on
68 W 116 W
Fan 2 3
Operating
temperatu
re
0°C to 45°C (32°F to 113°F)
Relative
humidity
(noncond
ensing)
10% to 90%
Quick Start
H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview
1-13
Table 1-7 System features of the S5100-EI series (3)
Item
S5100-8P
-PWR-EI
S5100-16
P-PWR-E
I
S5100-26C-
PWR-EI
S5100-50C-
PWR-EI
Dimensio
ns
(H × W ×
D)
43.6 ×
300 × 220
mm (1.7 ×
11.8 × 8.7
in.)
43.6 ×
300 × 260
mm (1.7 ×
11.8 ×
10.2 in.)
43.6 × 440 × 420 mm (1.7 ×
17.3 × 16.5 in.)
Weight
2.5 kg
(5.5 lb.)
< 3.1 kg
(< 6.8 lb.)
< 6.9 kg
(15.2 lb.)
< 7.4 kg
(16.3 lb.)
Managem
ent port
One console port
Service
ports
8 ×
10/100/10
00Base-T
autosensi
ng
Ethernet
ports
2 ×
1000Bas
e-X SFP
ports
16 ×
10/100/10
00
Base-T
autosensi
ng
Ethernet
ports
4 Gigabit
SFP
Combo
ports
24 ×
10/100/1000
Base-T
autosensing
Ethernet
ports
4 Gigabit
SFP Combo
ports
48 ×
10/100/1000
Base-T
autosensing
Ethernet
ports
4 Gigabit
SFP Combo
ports
Extension
slots
— —
Two 10 G
slots
Two 10 G
slots
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78

H3C H3C S5100-SI Series Quick start guide

Category
Network switches
Type
Quick start guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI