H3C H3C S5100-EI Series Quick start guide

H3C S5100-SI/EI Series

Ethernet Switches

Quick Start

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

Manual Version: T2-08018B-20070522-C-1.02

and its licensors

No part of this manual may be reproduced or transmitted in any form

or by any means without prior written consent of Hangzhou H3C

Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H

3

Care,

, TOP G, , IRF,

NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath,

Comware, Secware, Storware, NQA, VVG, V

2

G, V

n

G, PSPT, XGbus,

N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou

H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the

property of their respective owners.

Notice

The information in this document is subject to change without notice.

Every effort has been made in the preparation of this document to

ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of

any kind, express or implied.

To obtain the latest information, please access:

http://www.h3c.com

Technical Support

customer_service@h3c.com

http://www.h3c.com

About This Manual

Related Documentation

In addition to this manual, each H3C S5100-SI/EI Series Ethernet

Switches documentation set includes the following:

Manual Content

H3C S5100-SI/EI Series

Ethernet Switches Operation

Manual

It is used for assisting the users

in data configurations and

typical applications

H3C S5100-SI/EI Series

Ethernet Switches Command

Manua

It is used for assisting the users

in using various commands.

H3C S5100-SI/EI Series

Ethernet Switches Installation

Manual

It is used for assisting the users

in switch installation, booting up,

hardware and software

maintenance.

Organization

H3C S5100-SI/EI Series Ethernet Switches Quick Start is

organized as follows:

Chapter Contents

1 Product Overview

Introduces the characteristics and

technical specifications of S5100-SI/EI

Series Ethernet Switches.

Chapter Contents

2 Preparing for

Installation

Introduces the installation preparation and

precaution of S5100-SI/EI Series Ethernet

Switches.

3 Installing the Switch

Introduces the procedures to install an

S5100-SI/EI Series Ethernet Switch,

including the setup of the mainframe,

cards and cables.

4 Lightning Protection

of the Switch

Introduces lightning protection of

S5100-SI/EI Series Ethernet Switches.

Conventions

The manual uses the following conventions:

I.

GUI conventions

Convention Description

< >

Button names are inside angle brackets.

For example, click <OK>.

[ ]

Window names, menu items, data table

and field names are inside square

brackets. For example, pop up the [New

User] window.

/

Multi-level menus are separated by forward

slashes. For example, [File/Create/Folder].

Symbols II.

Convention Description

Warning

Means reader be extremely careful.

Improper operation may cause bodily

injury.

Caution

Means reader be careful. Improper

operation may cause data loss or damage

to equipment.

 Note Means a complementary description.

Environmental Protection

This product has been designed to comply with the requirements

on environmental protection. For the proper storage, use and disposal

of this product, national laws and regulations must be observed.

Quick Start

H3C S5100-SI/EI Series Ethernet Switches Table of Contents

i

Table of Contents

Chapter 1 Product Overview ........................................................1-1

1.1 Preface...............................................................................1-1

1.2 LEDs ..................................................................................1-4

1.3 System Features of the S5100 Series ...............................1-8

1.3.1 System Features of the S5100-SI Series................1-8

1.3.2 System Features of the S5100-EI Series................1-9

1.4 Ordering SFP Interface Modules .....................................1-16

1.5 Ordering 10 G Stack Interface Modules ..........................1-18

1.6 Ordering Stack Cables.....................................................1-18

1.7 Ordering DC Power cords................................................1-19

Chapter 2 Preparing for Installation ............................................2-1

2.1 Safety Precautions.............................................................2-1

2.2 Installation Site...................................................................2-1

2.2.1 Temperature/Humidity.............................................2-2

2.2.2 Cleanness................................................................2-3

2.2.3 Electromagnetic Susceptibility.................................2-4

2.2.4 Safety in Use of Laser .............................................2-4

2.3 Installation Tools ................................................................2-5

Chapter 3 Installing the Switch....................................................3-1

3.1 Rack-Mounting the Switch .................................................3-1

3.1.1 Introduction to Mounting Ear ...................................3-3

3.1.2 Introduction to Guide Rail........................................3-6

3.1.3 Using Front Mounting Ears to Install a Switch ........3-6

Quick Start

H3C S5100-SI/EI Series Ethernet Switches Table of Contents

ii

3.1.4 Use Front Mounting Ears and a Tray ......................3-8

3.1.5 Use Front and Rear Mounting Ears.........................3-9

3.1.6 Use Front Mounting Ears and Guide Rails............3-13

3.2 Desk Mounting .................................................................3-16

3.3 Wall Mounting ..................................................................3-17

3.4 Magnet Mounting .............................................................3-20

3.5 Connecting Power Cord and Grounding Wire .................3-23

3.5.1 Connecting AC Power Cord ..................................3-23

3.5.2 Connecting DC Power Cord..................................3-25

3.5.3 Connecting Grounding Wire ..................................3-27

3.6 Connecting Console Cable ..............................................3-32

3.6.1 Console Cable.......................................................3-32

3.6.2 Connecting Console Cable....................................3-33

3.7 Installing and Removing Optional Interface Modules ......3-35

3.7.1 XFP Interface Module............................................3-35

3.7.2 Stack Module.........................................................3-38

3.7.3 XENPAK Optical Module.......................................3-39

3.8 Installing and Removing Dedicated Stack Cables ...........3-42

3.8.1 Introduction............................................................3-42

3.8.2 Installation .............................................................3-43

3.8.3 Removal ................................................................3-43

3.9 Verifying the Installation...................................................3-44

Chapter 4 Lightning Protection of the Switch............................4-1

4.1 Installation of Lightning Arrester for AC Power (Socket Strip

with Lightning Protection).........................................................4-1

Quick Start

H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview

1-1

Chapter 1 Product Overview

1.1 Preface

H3C S5100 Series Ethernet Switches (hereinafter referred to as

the H3C S5100 series) are Gigabit Ethernet switching products

developed by H3C Technology Co., Ltd. The H3C S5100 series

provide a variety of service features. The H3C S5100 series are

designed as convergence and access devices for intranets and

metropolitan area networks (MANs), and can also be used for

connecting data center server clusters.

The H3C S5100 series come in two series: S5100-SI and

S5100-EI, which are available in the models listed in

Table 1-1:

An SFP port and its corresponding 10/100/1000Base-T

autosensing Ethernet port form a Combo port. That is, only one of the

two ports forming the Combo port can be used at a time.

Table 1-2

shows the mapping relations between the ports forming the Combo

port.

Quick Start

H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview

1-2

Table 1-1 H3C S5100-SI/EI series

Series Model

10/100/1

000Base

-T

autosen

sing

Ethernet

port

1000Base-

X SFP port

Console

port

S5100-8P-SI 8 2

S5100-16P-SI 16

S5100-24P-SI 24

S5100-S

I

S5100-48P-SI 48

4

S5100-8P-EI 8 2

S5100-16P-EI 16

S5100-24P-EI 24

S5100-48P-EI 48

S5100-26C-EI 24

S5100-50C-EI 48

4

S5100-8P-PWR

-EI

8 2

S5100-16P-PW

R-EI

16

S5100-26C-PW

R-EI

24

S5100-E

I

S5100-50C-PW

R-EI

48

4

1

Quick Start

H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview

1-3

Table 1-2 Mapping relations between the ports forming the

Combo port

Model

1000Base-X

SFP port

10/100/1000Base-T

autosensing

Ethernet port

17 14

18 16

19 13

S5100-16P-SI

S5100-16P-EI

S5100-16P-PWR-EI

20 15

25 22

26 24

27 21

S5100-24P-SI

S5100-24P-EI

S5100-26C-EI

S5100-26C-PWR-EI

28 23

49 46

50 48

51 45

S5100-48P-SI

S5100-48P-EI

S5100-50C-EI

S5100-50C-PWR-EI

52 47

Quick Start

H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview

1-4

1.2 LEDs

 Note:

z For the descriptions on the Ethernet port status LEDs and Ethernet

port mode LEDs (MODE) of the S5100 series, see H3C

S5100-SI/EI Series Ethernet Switches Installation Manual.

z Only the S5100-24P-EI, S5100-48P-EI, S5100-26C-EI,

S5100-50C-EI, S5100-26C-PWR-EI, and S5100-50C-PWR-EI

Ethernet switches provide DC power LEDs.

z Only the S5100-26C-EI, S5100-50C-EI, S5100-26C-PWR-EI, and

S5100-50C-PWR-EI Ethernet switches provide module LEDs.

Quick Start

H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview

1-5

Table 1-3 Description on the LEDs of the S5100-SI/EI series

LED Mark Status Description

Yellow, ON The switch is starting.

Green, ON

The switch has been normally

started.

Green, blinking

(1 Hz)

The system is performing

POST (power-on self test) or

downloading software.

Read, ON

The system POST has failed or

another fatal error has been

detected.

Yellow, blinking

(1 Hz)

One or more ports have failed

in POST or other non-fatal

errors have been detected.

Power

LED

PWR

OFF

The switch has been powered

off.

Green, ON

Both AC and DC inputs are

normal.

Yellow, ON

The AC input is abnormal; the

DC input is normal.

DC

power

supply

LED

RPS

OFF There is no DC input.

Quick Start

H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview

1-6

LED Mark Status Description

OFF

The module has not been

installed or connected.

Green, ON

The module has been installed

and connected.

Green, blinking

The module is receiving or

sending data.

Yellow, blinking

(3 Hz)

Module POST has failed.

Modul

e LED

MOD

1 (or

MOD

2)

Yellow, ON

The device does not support

this module.

POST

runni

ng

Green,

blinkin

g

The POST ID of the in-process

test is displayed.

POST

failed

Red,

ON

The POST ID of the failed test

blinks.

Loadi

ng

softw

are

Green,

blinkin

g

A light bar rotates clockwise

around the display during the

downloading procedure.

7-seg

ment

digitro

n

displa

y

Unit

Fan

failure

Red,

ON

An “F” is displayed.

Quick Start

H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview

1-7

LED Mark Status Description

A “1” is displayed.

Unit

ID

Green,

ON

A “C” is displayed on command

switch.

Clust

er

mana

geme

nt

Green,

ON

An “S” is displayed on member

switch.

A “c” is displayed on candidate

switch.

An “I” is displayed on

independent switch.

Over-

temp

eratur

e

alarm

The digitron display shows a

"t".

Red,

ON

PoE

status

(for

the

S510

0-EI

series

only)

The ratio of the power used by

the port for PoE to the total

available power is displayed.

Green,

ON

0 - 20%

21 - 40%

41 - 60%

61 - 80%

81 - 100%

Quick Start

H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview

1-8

1.3 System Features of the S5100 Series

1.3.1 System Features of the S5100-SI Series

Table 1-4 System features of the S5100-SI series

Item

S5100-8P-S

I

S5100-16P-

SI

S5100-24

P-SI

S5100-48P-

SI

Dimensi

ons

(H × W

× D)

43.6 × 230 ×

200 mm (1.7

× 9.1 × 7.9

in.)

43.6 × 300 ×

220 mm (1.7

× 11.8 × 8.7

in.)

43.6 × 440 × 260 mm

(1.7 × 17.3 × 10.2 in.)

Weight

< 1.6 kg (<

3.5 lb.)

< 2.3 kg (<

5.1 lb.)

< 4 kg (<

8.8 lb.)

4 kg (8.8 lb.)

Service

ports

8 ×

10/100/1000

Base-T

autosensing

Ethernet

ports

2 ×

1000Base-X

SFP ports

16 ×

10/100/1000

Base-T

autosensing

Ethernet

ports

4 Gigabit

SFP Combo

ports

24 ×

10/100/1

000

Base-T

autosensi

ng

Ethernet

ports

4 Gigabit

SFP

Combo

ports

48 ×

10/100/1000

Base-T

autosensing

Ethernet

ports

4 Gigabit

SFP Combo

ports

Manage

ment

port

One console port

Power

supply

system

The S5100-SI series support AC power input.

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or

60Hz

Max voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

Quick Start

H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview

1-9

Item

S5100-8P-S

I

S5100-16P-

SI

S5100-24

P-SI

S5100-48P-

SI

Max

power

consum

ption

16 W 25 W 39 W 78 W

Fan 1 1 1 2

Operati

ng

tempera

ture

0°C to 45°C (32°F to 113°F)

Relative

humidit

y

(noncon

densing

)

10% to 90%

1.3.2 System Features of the S5100-EI Series

Table 1-5 System features of the S5100-EI series (1)

Item

S5100-8P-

EI

S5100-16P-

EI

S5100-24

P-EI

S5100-48

P-EI

Dimensio

ns

(H × W ×

D)

43.6 × 230

× 200 mm

(1.7 × 9.1 ×

7.9 in.)

43.6 × 300 ×

220 mm (1.7

× 11.8 × 8.7

in.)

43.6 × 440 × 260 mm

(1.7 × 17.3 × 10.2 in.)

Weight

< 1.6 kg (<

3.5 lb.)

< 2.3 kg (<

5.1 lb.)

< 4 kg (<

8.8 lb.)

4 kg (8.8

lb.)

Quick Start

H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview

1-10

Item

S5100-8P-

EI

S5100-16P-

EI

S5100-24

P-EI

S5100-48

P-EI

Service

ports

8 ×

10/100/100

0Base-T

autosensin

g Ethernet

ports

2 ×

1000Base-

X SFP ports

16 ×

10/100/1000

Base-T

autosensing

Ethernet

ports

4 Gigabit

SFP Combo

ports

24 ×

10/100/10

00Base-T

autosensin

g Ethernet

ports

4 Gigabit

SFP

Combo

ports

48 ×

10/100/10

00Base-T

autosensin

g Ethernet

ports

4 Gigabit

SFP

Combo

ports

Managem

ent port

One console port

Power

supply

system

The S5100-EI series support AC input and DC input.

AC input:

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or

60Hz

Max voltage range: 90 VAC to 264 VAC, 47 Hz to 63

Hz

DC input (for the S5100-24P-EI and S5100-48P-EI):

Rated voltage range: -48 VDC to -60 VDC

Max voltage range:-36 VDC to -72 VDC

Max

power

consumpt

ion

18 W 26 W 46 W 97 W

Fan 1 1 1 2

Operating

temperatu

re

0°C to 45°C (32°F to 113°F)

Quick Start

H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview

1-11

Item

S5100-8P-

EI

S5100-16P-

EI

S5100-24

P-EI

S5100-48

P-EI

Relative

humidity

(noncond

ensing)

10% to 90%

Table 1-6 System features of the S5100-EI series (2)

Item S5100-26C-EI S5100-50C-EI

Dimensio

ns

(H × W ×

D)

43.6 × 440 × 300 mm (1.7 × 17.3 × 11.8 in.)

Weight 4 kg (8.8 lb.) < 5 kg (< 11 lb.)

Service

ports

24 ×

10/100/1000MBase-T

autosensing Ethernet

ports

4 Gigabit SFP Combo

ports

48 ×

10/100/1000MBase-T

autosensing Ethernet

ports

4 Gigabit SFP Combo

ports

Extension

slots

Two 10 G slots Two 10 G slots

Managem

ent port

One console port

Quick Start

H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview

1-12

Item S5100-26C-EI S5100-50C-EI

Power

supply

system

The S5100-EI series support AC input and DC input.

AC input:

Rated voltage range: 100 VAC to 240 VAC, 50 Hz or

60Hz

Max voltage range: 90 VAC to 264 VAC, 47 Hz to 63

Hz

DC input:

Rated voltage range: -48 VDC to -60 VDC

Max voltage range: -36 VDC to -72 VDC

Max

power

consumpti

on

68 W 116 W

Fan 2 3

Operating

temperatu

re

0°C to 45°C (32°F to 113°F)

Relative

humidity

(noncond

ensing)

10% to 90%

Quick Start

H3C S5100-SI/EI Series Ethernet Switches Chapter 1 Product Overview

1-13

Table 1-7 System features of the S5100-EI series (3)

Item

S5100-8P

-PWR-EI

S5100-16

P-PWR-E

I

S5100-26C-

PWR-EI

S5100-50C-

PWR-EI

Dimensio

ns

(H × W ×

D)

43.6 ×

300 × 220

mm (1.7 ×

11.8 × 8.7

in.)

43.6 ×

300 × 260

mm (1.7 ×

11.8 ×

10.2 in.)

43.6 × 440 × 420 mm (1.7 ×

17.3 × 16.5 in.)

Weight

2.5 kg

(5.5 lb.)

< 3.1 kg

(< 6.8 lb.)

< 6.9 kg

(15.2 lb.)

< 7.4 kg

(16.3 lb.)

Managem

ent port

One console port

Service

ports

8 ×

10/100/10

00Base-T

autosensi

ng

Ethernet

ports

2 ×

1000Bas

e-X SFP

ports

16 ×

10/100/10

00

Base-T

autosensi

ng

Ethernet

ports

4 Gigabit

SFP

Combo

ports

24 ×

10/100/1000

Base-T

autosensing

Ethernet

ports

4 Gigabit

SFP Combo

ports

48 ×

10/100/1000

Base-T

autosensing

Ethernet

ports

4 Gigabit

SFP Combo

ports

Extension

slots

— —

Two 10 G

slots

Two 10 G

slots

Page is loading ...

H3C H3C S5100-EI Series Quick start guide

This manual is also suitable for

H3C H3C S5100-EI Series Quick start guide

Related papers

Other documents