Page is loading ...
SECTION TITLE
KEY FEATURES
GENERAL SPECIFICATIONS
The Pro-Trac 200 is a heavy-duty
positioner engineered for
continuous, reliable operation.
Common application uses for the
Pro-Trac 200 include chasing
systems, moving-sensor center
guide systems, web width
measurement systems, or simple
sensor positioning.
Adaptable to almost any application, the Pro-Trac 200 features a dust-tight design, with ball bearings in
all moving parts for low friction and extended operating life. Optional self-tracking cable carriers eliminate
the risk of damaged cables. Available primarily as an electromechanical positioner; the Pro-Trac 200 is also
available in hydraulic and manual configurations.
•Heavy-duty positioner designed for
continuous operation
•Manual, hydraulic, or
electromechanically powered with edge
or center guide configurations
•Optional self-tracking cable carriers
•Virtually maintenance-free, dust-tight
design
•Ball bearings in all moving parts
provide extended operating life
•Motor drives available in D.C. servo
motor, D.C. motor, or stepping motor,
depending on application
•Positioner can be mounted in
virtually any orientation
•Control legends available either in
English or international symbols
ELECTROMECHANICAL SENSOR POSITIONER
Pro-Trac 200
PRO-TRAC 200
Chasing Application
Moving-sensor center guide with optional web width measurement
Typical Applications
1. Processor
2. Guide
3. Pro-Trac 200
4. Sensors
5. Servo-Center
6. AC Power In
7. Pulse Transmitter
8. Set Point Switch
9. Electronic Digital Display
NORTH, CENTRAL
AND SOUTH AMERICA
Tel +1.405.755.1600
Fax +1.405.755.8425
www.maxcessintl.com
INDIA
Tel +91.22.27602633
Fax +91.22.27602634
www.maxcess.in
EUROPE, MIDDLE EAST
AND AFRICA
Tel +49.6195.7002.0
Fax +49.6195.7002.933
www.maxcess.eu
JAPAN
Tel +81.43.421.1622
Fax +81.43.421.2895
www.maxcess.jp
CHINA
Tel +86.756.881.9398
Fax +86.756.881.9393
www.maxcessintl.com.cn
KOREA, TAIWAN
AND SE ASIA
Tel +65.9620.3883
Fax +65.6235.4818
©2013 Maxcess
H = B
1
+ 2F + 1.88 [47.6]
K = ADJUSTABLE (H - 4.88 [124.0] STD)
CABLE CARRIERS AS REQ'D
1 [25.4]
0.50 [12.7]
1.5
[38.1]
MIN
1.48 [37.6]
6.5
[165.1] 5.00
[127.0]
3.54
[89.9]
0.75
[19.0]
0.44 [11.2] DIA THRU
FOUR HOLES FOR
3/8 (M10) DIA
MOUNTING BOLTS
LIMIT SWITCHES CAN
BE INSTALLED IF
REQUIRED BY CON-
TROL SYSTEM
1.88
[47.6]
8.5
[215.9]
7.0
[177.8]
B1 (MAXIMUM OPENING)
B2 (MINIMUM OPENING)
MAXIMUM OPENING = 100 [2540.0] FOR
STANDARD DRIVE
SPECIAL LENGTHS AVAILABLE
UPON REQUEST
2.50
[63.5]
MIN
4.38
[111.3]
MIN
G
FD
C
8.0
[203.2]
4.70
[119.4]
4.05
[102.9]
NOTES:
·Dimensions shown in parenthesis are in millimeters
·Typical electromechanical configuration, other mounting types and actuators are available to match your application requirements
·If optional 51 mm (2 inch) standoff is used, “B” dimensions increase by 102 mm (4 inches)
·Standard sensor mounting bracket shown. Additional sensor mounting brackets are available to accommodate other Fife sensors
·Positioner can be mounted in any orientation
PRO-TRAC 200
ELECTROMECHANICAL SENSOR POSITIONER
SENSOR B2 C D F
INCH MM INCH MM INCH MM INCH MM
SE-22 6.38 162 2.07 53 2.63 57 5.62 143
SE-23 4.88 124 2.06 52 3.38 86 6.38 162
SE-31 6.38 162 2.07 53 2.63 57 5.62 143
/
