Kensington H3000 User manual

Brand: Kensington

Model: H3000

Type: User manual

Kensington H3000: Enhance your productivity with seamless wireless communication and superior audio quality. Experience crystal-clear calls with a noise-canceling microphone and immerse yourself in rich audio with powerful speakers. Enjoy up to 8 hours of talk time with a single charge and quickly recharge with the included USB-C cable. The headset's intuitive controls allow for easy volume adjustment, play/pause music, and mute the microphone. Stay connected and focused with Kensington H3000, your ultimate communication companion for work and personal use.

Kensington H3000 Bluetooth Over-Ear Headset.

1. The headset, USB-C charging cable, USB-C receiver, and USB-A adapter are stored inside the travel case in dedicated compartments.

2. After removing your headset from the case, adjust the earcups so the memory foam earpads are facing each other.

3. Adjust your headset for optimal comfort and performance. Adjust the headband on both sides so the earpads rest comfortably over your ears.

Adjust the rotating microphone so it is directly in front of your mouth.

3a. This is a ﬂip-to-mute microphone. When the microphone is up, the microphone is automatically muted.

3b. To unmute the microphone, swing the microphone arm down into the active position.

4. The power button, Bluetooth pairing / voice assistance button, and USB-C charging port are located on the lower edge of the earcup with the earcup controls.

To turn your headset on, slide the power button to the right. A blue light will illiuminate. Slide the power button to the left to turn the headset off.

To pair a device, press and hold the Bluetooth pairing / voice assistance button down for 5 seconds.

To enable voice assistance commands, press the Bluetooth pairing / voice assistance button two times.

5. To pair your headset with your device, slide the headset power button to the on position. To connect using the pre-paired USB-C receiver, plug the headset's USB-C receiver into any available USB-C

port on your device or connect the USB-A adapter to the USB-C receiver and then plug the USB-A adapter into any available USB-A port.

To connect via built-in Bluetooth, press and hold the Bluetooth pairing button for 5 seconds until the blue light illuminates, then open your device's Bluetooth window and select the H3000 Headset.

6. Use your earcup controls to maximize your productivity. Locate the volume buttons on the side of the earcup. Press the "+" button to increase the volume and the "-" button to decrease the volume.

The center button on your earcup has many functions. Press the center button once to play or pause music. Press the center button three times to turn sidetone on or off.

7. Press and hold the center button for two seconds to turn the busy lights on. Press the center button twice to cause the busy lights to ﬂash red.

Press and hold the center button for 2 seconds to turn the busy lights off.

8. USB-C receiver indicator light. If the light on the USB-C receiver is off, the headset is not connected. A blue light on the USB-C receiver indicates the headset is connected to the device.

A red light on the USB-C receiver indicates the headset is muted.

9. Power indicator light. The power light will turn solid blue for 3 seconds when the headset is turned on. A solid green light indicates the headset is fully charged.

A slow blinking red light indicates the headset is charging. A ﬂashing red light indicates the headset's battery is less than 10%.

If the power light is alternating between red and blue, the Bluetooth is not connected. A quick ﬂashing blue light indicates the headset is in pairing mode.

A ﬂashing blue light indicates the Bluetooth is connected.

To charge the headset, connect the USB-C charging cable to the headset's charging port. For USB-C connections, plug the USB-C end into any available USB-C port on your device.

For USB-A connections, connect the USB-A adapter to the USB-C receiver, then plug the USB-A adapter into any available USB-A port.

15 minutes of charging time will provide 8 hours of headset use. 90 minutes of charging time will fully charge your headset battery to 100%.