Page is loading ...
•Customize your headset and USB adapter settings to your personal preferences
•Automatically manage your PC multimedia so you never miss a call
•Quickly access links to product support and software/firmware upgrade information
Registering Your Product and Plantronics Software
Visit plantronics.com/productregistration to register your product online so we can
provide you with the best service and technical support.
We also recommend that you install the Plantronics software located at plantronics.com/
software. With it installed you can:
Voyager Focus UC
Quick Start Guide
ANC
,ĞĂĚƐĞƚ
Charge stand
USB Bluetooth adapter
Volume up/down
Track backward*
Play/pause music*
Track forward*
Active noise cancelling
Charge port
Active call = mute/unmute
Idle = OpenMic (hear your surroundings)
Headset LEDs for pairing, battery status, online indicator
Call button ([ ])
Power button
Bluetooth pair button
Fit
WEAR ON THE RIGHT OR LEFT To position the microphone on the right or left
side, rotate the microphone boom up and over. Adjust the boom so it points
to the corner of your mouth.
TIP Your headset senses when you change the microphone boom from one
side to the other and syncs the audio and controls specific to each side.
Charging your headset
IMPORTANT Before using, charge the headset fully to reset the accuracy of
the talk time prompts.
Charge your headset with the charge stand or the micro USB cable. The
headset LEDs flash when charging. It takes up to 2 hours to fully charge your
headset. The LEDs turn off once charging is complete.
NOTE Both the charge stand and micro USB cable can be plugged into either a
computer or wall charger. It is only necessary to plug into a computer to
update firmware.
Charge
stand
Micro USB
cable
Headset LEDs Battery status
4–5 blue blinks Battery high
2–3 blue blinks Battery medium
1 red blink Battery low
flashing red Battery critical; Recharge headset
Your Bluetooth USB adapter comes pre-paired to your headset.
1Insert the Bluetooth USB adapter into your laptop or PC.
2Pairing is successful when you hear “pairing successful” and the USB adapter LED
is solid blue.
3OPTIONAL: Headset call control Some softphones require the installation of
Plantronics Hub for Windows and Mac (plantronics.com/software) to enable
headset control (answer/end and mute) functionality.
NOTE Plantronics Hub software also allows you to customize your headset's
behavior through advanced settings and options.
Your high-fidelity Bluetooth USB adapter comes ready to take calls. If you want
to listen to music, you will need to configure your Bluetooth USB adapter.
Windows
1To configure your Bluetooth USB adapter to play music, go to Start menu >
Control Panel > Sound
>Playback tab. Select Plantronics BT600, set it as the Default Device and click OK.
2To pause music when you place or receive calls, go to Start menu > Control Panel
>Sound > Communications tab and select the desired parameter.
Mac
3To configure the Bluetooth USB adapter, go to Apple menu > System Preferences
> Sound. On both the Input and Output tabs, select Plantronics BT600.
Connect to PC
Configure USB adapter
Pair to mobile to Device 1To put your headset in pair mode, press and hold the power button towards the Bluetooth
icon until you hear "pairing" and the headset LEDs flash red and blue.
2Activate Bluetooth on your phone and set it to search for new devices.
•iPhone Settings > Bluetooth > On*
•Android Settings > Bluetooth: On > Scan for
devices* NOTE *Menus may vary by device.
3 Select “PLT_Focus.”
If necessary, enter four zeros (0000) for the passcode or accept the connection.
Once successfully paired, you hear “pairing successful” and the headset LEDs stop flashing.
NOTE Your headset can pair with up to 8 devices but only maintain 2 connections
simultaneously; this includes the Bluetooth USB adapter.
Some softphones require the installation of Plantronics Hub for Windows and Mac to enable
headset control (answer/end and mute) functionality.
1Install Plantronics Hub for Windows and Mac onto your computer by visiting plantronics.com/
software.
2Manage your headset settings with your computer or mobile device with Plantronics Hub for
Windows and Mac or Plantronics Hub for iOS and Android, respectively (plantronics.com/
software).
Plantronics Hub iOS and Android Windows and Mac
Call control for softphones X
Change headset language X
Update firmware X
Turn features on/off X X
View user guide X
Battery meter X X
Load Software
Voice dial (smartphone)
If your smartphone has a voice-enabled assistant, press and hold the Call button for 2 seconds
and wait for the phone prompt and then tell the phone to dial the number of a stored contact.
While on an active call, choose:
• Tap the red Mute button
• Take off/put on your headset while on an active call (requires active smart sensors)
* Plantronics Hub for Windows and Mac required (plantronics.com/software)
If you have muted an active call and you start to speak, then a desktop notification reminds you
that you are on mute. You can add a voice prompt notification by managing your mute features
with Plantronics Hub for Windows and Mac.
While not on a call, tap the red Mute button to activate OpenMic and hear your surroundings.
Control the level of ambient noise you hear by adjusting the volume wheel.
Rotate the volume wheel forward (+) or backward (–) to control the volume.
Choose:
•Put on/take off the headset (requires active smart sensors)
• Tap the Play/pause button
NOTE Functionality varies by application. Does not function with web-based apps.
Tap the Forward button or Back button to control the track selection. NOTE
Functionality varies by application. Does not function with web-based apps.
Mute/unmute
Mute on reminder*
OpenMic
Volume
Play or pause music
Track selection
NOTE *Functionality varies by application. Does not function with web-based apps.
Answer or end a call: Tap the Call button.
Make/Take/End Calls Call back last call (smartphone): To dial your last number you dialed, double-tap the Call button.
With active sensors putting on the headset will: taking off the headset will:
Call answer the call mute the headset
Music/media resume music/media (if
playing previous to taking off)*
pause music/media (if playing)*
Mute unmute if on an active call mute if on an active call
NOTE *Functionality varies by application. Does not function with web-based apps.
Reset sensors
You may need to reset the sensors if they are not working as expected.
There are two ways to reset the headset sensors. Choose:
•
•
With your headset powered on, charge your headset on the charge stand for 10 seconds
Press and hold both the Mute and Play/pause buttons for more than 4 seconds until the
LEDs flash purple twice, being careful to not touch the earcup padding or allow it to come in contact
with surfaces
Disable sensors
You can disable your headset smart sensors several ways:
Use sensors
•Manage sensors through Plantronics Hub software
•Hold both the Mute and Call buttons for more than 4 seconds until the LED flashes
purple then red. Repeat to reactivate; the LED flashes purple then blue.
NOTE Sensors cannot be disabled while streaming audio.
Active Noise Cancelling (ANC) reduces unwanted noise.
Your headset ships with ANC on. To turn ANC off, slide the stitch away from "ANC."
ANC
/
