Ergolux ELESTNDSKWA User guide

Brand: Ergolux

Model: ELESTNDSKWA

Category: Measuring, testing & control

Type: User guide

ELECTRIC STANDING

DESK

ELESTNDSKNA, ELESTNDSKBA & ELESTNDSKWA

• Read all instructions before use and retain this user guide for future reference.

• Read all following safety precautions carefully before use.

• Your equipment is i nt en de d fo r us e in c oo l, dr y co ndi ti on s. Yo u sh ou ld a vo id s to ra ge i n

extreme cold, hot or damp areas as this may lead to corrosion and other related

problems.

• This desk is rated at a maximum weight capacity of 70kg.

• This desk is designed for indoor use only.

• Do not modify the desk frame or any of the components that operate this desk in any

way.

• If the power cord is damaged, cease use immediately and contact help.Kogan.com for

support.

• If the control box emits any abnormal noises or strong odours, cease use immediately

and contact help.Kogan.com for support.

• Ensure any obstacles are removed from the area around the desk during assembly and

operation.

• Ensure that all cords and wires are arranged in a way where they are not a tripping

hazard.

• Unplug the power cord before cleaning. Wipe the dust from the surface using a slightly

damp cloth. Ensure any water does not come in contact with any internal parts or

connectors.

• Do not disassemble or perform any maintenance without disconnecting the power first.

• Do not use any corrosive or abrasive materials to clean the product.

• The control box contains electronic components, metals, plastics, wires etc. ensure it is

disposed of in accordance with your local environmental legislation. Do not dispose

with general household waste.

• Ensure this product is completely and correctly assembled before use.

• Be familiar with all functions and program settings of the product before first use.

• This product can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning use of the appliance in a

safe way and understand the hazards involved.

• Children should not be allowed play with this product.

• Cleaning and user maintenance should not be performed by children without

supervision.

• Retain the original packaging where possible, to use for any future transportation of this

product.

SAFETY & WARNINGS

Lay all components out on a clean floor and ensure all parts are included. If any pieces are

missing, check all packaging thoroughly, then contact help.Kogan.com for assistance.

A Desktop

B Sync Rod

C Lifting Column

D Lifting Column

E Side Bracket (x2)

F Foot (x2)

G Crossbar (x2)

H Motor

I AC Adapter

J Controller

COMPONENTS

Hardware List

S-A M4x40

Phillips Head Screw (x4)

S-B M6x12 Hex

Head Screw (x22)

S-C M6x30 Hex

Head Screw

(x10)

S-D ST4.0x12

Phillips Head Screw

(x4)

Too l s R e q u i red

4mm Allen key

(included)

Spirit Level

(not included)

Phillips Head Screwdriver

(not included)

Step 1: Installing the feet.

• Attach the Feet (F) to the bottom of the Lifting Columns (C) (D) using x8 M6x30 Hex

Head Screws (S-C).

S-C (x8)

4mm Allen key

ASSEMBLY

Step 2: Attaching the Sync Rod

• Insert the end of the Sync Rod (B) without the notch though the Motor (H).

• Insert the Sync Rod (B) into the holes on the Lifting Columns (C)(D).

• Secure the motor in place using x2 M4x40 Phillips Head Screws (S-A).

S-A (x2)

Notch

Step 3: Attaching the Crossbars

• Attach the Crossbars (G) to the Lifting Columns (C)(D) using x8 M6x12 Hex Head

Screws (S-B).

Note: Ensure the screws are inserted into the outer most holes on the crossbars and

lifting columns.

S-B (x8)

Step 4: Attaching the Side Brackets

• Attach the Side Brackets (E) to the Lifting Columns (C)(D) using x4 M6x12 Hex Head

Screws (S-B).

Note: Ensure the Side Brackets are attached to the two holes second from the top of

the upper edge of the lifting columns.

S-B (x4)

Step 5: Attaching the Desktop

• Lay the Desktop (A) face down on a soft, flat surface (carpet, blanket etc.).

• Attach desk frame assembly to the Desktop (A) using x8 M6x12 Hex Head Screws

(S-B).

S-B (x8)

Step 6: Connecting the Controller

• Connect the AC Adapter (I) and the Motor (H) connectors to the mating connectors on

the Controller (J).

Note: Do not plug the AC Adapter into power until assembly is complete.

Blanket

Step 7: Attaching the Controller

• Attach the Controller (J) to the Desktop (A) using x2 ST4.0x12 Screws (S-D).

S-D (x2)

Step 8: Adjusting the Desk

• Turn the Desk back over to the upright position.

• Use a spirit level to ensure the desk is level and stable. Each foot has two adjustable

pads that can be rotated to raise or lower the desk.

CAUTION: To avoid serious injuries, at least two people are required

when turning the desk over.

Spirit level

Before First Use

When the desk is first powered on, the height will be displayed on the controller. If this

number does not match the actual height of the desk, the system will need to be reset

before use.

Resetting the System

1. Use the “ ” button to place the desk in the lowest position, then and press hold

the “ ” button for 7 seconds until the display is alternately flashing “RST” and

“E-1”. Release the “ ” button

2. Press and hold the “ ” button again, the desk will move downward slightly and

then move upwards approximately 5mm.

3. The system has now successfully been reset.

Note: To r e s e t a d e s k w i t h a c u s t o m i s e d m i n i m u m h e i g h t , y o u w i l l n e e d t o p r e s s a n d h o l d

both the “ ” and “ ” buttons simultaneously.

Adjusting the Height

Press the “” or “ ” or buttons to adjust the height of the desk. The display will show

the current height.

OPERATION

Display

Raise

Lower

Memory

1/2/3

Settings

Memory Setting

1. To save a position to one of the three memory buttons, first adjust the desk to the

desired height.

2. Press the “S” button, the display will flash the current height then press either the

“1”, “2” or “3” button. The current height will be stored to the respective button.

3. To use one of the saved positions, press either the “1”, “2” or “3” button. The desk

will move to the saved position.

Switching Units (CM/INCH)

1. Press and hold the “S” button until “SET” is displayed.

2. Press “1” to enter the unit menu. The display will alternately flash “unt” and the

current height.

3. Press the “” or “ ” or buttons to switch the unit of measurement.

4. Press the “S” button to save your selection.

Collision Avoidance

1. Press and hold the “S” button until “SET” is displayed.

2. Press “2” to enter the collision avoidance menu. The display will alternately flash

“cpt” and the current sensitivity level.

3. Press the “” or “ ” or buttons to adjust the sensitivity level.

4. Press the “S” button to save your selection.

Controller Lock

1. Press and hold the “S” button until “SET” is displayed.

2. Press “3” to lock the controller. The display will flash “OFF”. Note: In this current

state any buttons pressed will have no effect.

3. Press and hold the “S” button for 3 seconds to unlock the controller.

Setting a Custom Minimum & Maximum Height Limit

1. Press and hold the “S” button until “HLP” is displayed.

2. The display will alternately flash “HLP” and the current height.

o Adjust the desk to your desired maximum height and press “1”. The display

will flash “H-P”, press “S” to store the height.

o Adjust the desk to your desired minimum height and press “2”. The display

will flash “L-P”, press “S” to store the height.

o Press “3” to remove the previously stored height settings.

Deleting Custom Settings

1. Press and hold the “S” button until “FAC” is displayed, then release the button.

2. Press the “S” button again to remove all custom settings.

The following tips will help you detected and eliminate some common faults and errors. If

the problem cannot be fixed or the fault is not listed below, please contact help.Kogan.com

for support.

Error Code

Solution

Err

The control panel is disconnected. Check the

connection. Disconnect the power then

reconnect it.

E-1

Reset the system.

E-2

The weight rating has been exceeded. Remove

all items from the desktop and reset the system.

E-3

The collision avoidance system has activated.

Remove all items within the desk’s range of

motion.

E-5

Check all connection and reset the system.

ovr

An overload has occurred. Remove all items

from the desktop and reset the system.

hot

The system has overheated. Cease operation

and allow the desk to remain idle for

approximately 10 minutes.

voL

An electrical fault has occurred. Disconnect the

power then reconnect it.

Disposal

This marking indicates that this appliance should not be disposed with other

household wastes. To prevent possible harm to the environment or human

health from uncontrolled waste disposal, recycle it responsibly to promote

the sustainable reuse of material resources.

TROUBLESHOOTING

NOTES

Need more information?

We hope that this user guide has given you

the assistance needed for a simple set-up.

For the most up-to-date guide for your product,

as well as any additional assistance you may require,

head online to help.kogan.com

Ergolux ELESTNDSKWA User guide

Brand: Ergolux

Model: ELESTNDSKWA

Category: Measuring, testing & control

Type: User guide

Download PDF

report

Ergolux ELESTNDSKWA User guide

Ergolux ELESTNDSKWA User guide

Related papers

Other documents