2. Fletcher-Terry
  3. 09-207

Fletcher-Terry 09-207, 09-228, 09-234, 09-236, FLETCHER-Terry No Wire Hanging System Kit, No Wire Hanging System Kit User manual

  • Hello! I have reviewed the installation instructions for the Fletcher-Terry Hanging System, model 450001015. This document provides step-by-step guidance for installing the no-wire hanging system for frames of various sizes. I'm ready to help answer any questions you have about the installation process.
  • What tools are needed for installation?
    What is included in the parts list?
    What should I do if my wall is hard or textured?
No-Wire Hanging System
INSTALLATION INSTRUCTIONS
TOOLS
~
PARTS
LIST
\ ~
QP
~
2Mark
e
ra
g
Hammer&phllllpshead
c,
c.?
----~----
~ 1 Bumper
ocr,wdrivor
2
Brackets
1
Level
~
811
1
~------'
4
Scrawa
1
Strtp
of
llpe
11
bra
are
alre
FOR
SMALL
FRAMES
Hach
brackets
o
frame
1/3
Insert
markers
~
9<1'
te
to
lock
attached
to
f
proceed
to
Step
1
A •
Attach
level
to
top
of
Do
~OT
attach
foam
tape
to
V
frame
using
tape.
decora/Jve
moldmgs
such
as
those
e
0
, __
•
Attach
bumper
to
with
a "
gold
leaf
"
finish
bottom
of
frame
:
in
the
middle.
•
Determine
desired
location
&
make
sure
your
frame
is
level.
Press
firmly
against
the
wall
to
make
2
dimple
marks.
Tip:
If
wall
surface
is
hard
or
textured
,
color
the
tip
of
the
dimple
with
a
crayon
to
make
a
visible
mark
on
the
wall.
Then
use
a
large
nail
or
punch
to
create
a
cavity
the
same
size
as
the
dimple
.
Rotate
markers
to
unlock
and
remove
them
from
the
brackets;
then
place
the
markers
into
the
dimples
and
nail
the
markers
to
the
wall
Push
brackets
onto
the
markers,
then
pull
down
to
lock
in
place.
Remove
tape
and
bubble
level
to
complete
your
installation.
~·
··
1/
1/
'
/etch
er
Part
#4
5
0001015
Last
Rev.
Date:
09/20
1
FOR
FRAMES
20"
or
WIDER
0 •
Attach
brackets
to
both
sides
of
frame
oo
-
•
Insert
a
marker
into
the
,:
LEFT
bracket
•
Determine
desired
mounting
location
. , /
•
Press
frame
firmly
into
wall
surface
to
create
LEFT
dimple
mark
8 Rotate
to
unlock
marker
Insert
marker
into
dimple
and
nail
into
wall
e •
Affix
foam
tape
&
level
to
frame
:;;;;,;.::--
..
fn
n ~)
0
•
Seat
LEFT
bracket
onto
marker
that
is
on
the
wall
•
Allow
frame
to
swing
down
•
Raise
frame
until
bubble
reads
"level"
•
Press
RIGHT
side
of
frame
firmly
into
wall
surface
to
make
RIGHT
dimple
mark
·,
•
Allow
frame
to
swing
down
•
Repeat
Step
#2
to
install
the
RIGHT
marker
•
Push
brackets
onto
the
markers,
then
pull
down
to
lock
in
place.
•
Remove
tape
and
bubble
level
to
complete
your
installation.
To
see
installation
video,
go
to:
www.fletcher-terry.com
©2018
The
Fletcher-Terry
Company,
LLC.
All
rights
reserved_
U.S.
Patent
Nos
.
7,497
,
028
and
7,836,605.
Other
p~tent~
pending
Designed
and
engineered
in
the
U.S.
-
Made
in
China
.
/