Astria Fireplaces 900005-07 Installation guide

Brand: Astria Fireplaces

Model: 900005-07

Type: Installation guide

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

INSTALLATION INSTRUCTIONS FOR FRAMING STANDOFF AND VENT GASKET

FOR USE WITH SIGNATURE

SERIES ENVY AND ENVY CD DIRECT-VENT GAS FIREPLACES

[FIREPLACE MODELS ENVY35TEN, ENVYCD35TEN, ENVY40TEN, ENVYCD40TEN, ENVY45TEN, ENVYCD45TEN]

P/N 900005-07

Rev. A 10/2014

HEARTH PRODUCTS

KITS AND ACCESSORIES

FRAMING STANDOFF AND VENT GASKET

CAUTION

RISK OF PERSONAL INJURY OR PROPERTY DAMAGE.

•Never operate fireplace without liner panels installed.

•These appliances are NOT approved for operation without

liner panels.

•Do NOT abuse glass doors by striking or slamming shut.

•Never operate fireplace with glass door assembly removed.

•Handle glass door assembly with extreme care. Replace

damaged glass door assembly with approved replacement

assembly only.

•Use only media approved for use with these fireplaces (as

applicable). Failure to use approved media may result in sooting,

delayed ignition, or other improper fireplace operation, and may

void the warranty.

NOTICE

•READ ALL STEPS BEFORE STARTING INSTALLATION.

•LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE.

•All warnings, precautions, and instructions in the Installation

Instructions and Care and Operation Instructions provided with the

appliance also apply to these instructions.

•If you encounter any problems, need clarification of these

instructions, or are not qualified to properly install this kit, contact

your local distributor or dealer.

GENERAL INFORMATION

This kit contains all the necessary components to assemble and

install the ENVY and ENVY CD framing standoff and the top vent

rope gasket.

The information provided must be used in conjunction with the

Care and Operation Instructions. Please read the instructions

completely before performing the procedures detailed in

this document.

REQUIRED TOOLS

•

5/16 in. Hex-head nut driver

KIT CONTENTS

• Left side framing

standoff (1)

• Right side framing

standoff (1)

• Center support (1)

• 5/16 in. Hex head

screws (8)

• Rope gasket (1)

FRAMING STANDOFF KIT INSTALLATION INSTRUCTIONS

1. Bend both standoffs at the designated places to prepare the

components for installation (

Figure 1).

Figure 1: Bending the framing standoffs

2. Align the right side of the framing standoff with the right side

of the ﬁreplace (Figure 2). Secure the standoff with two (2)

of the included 5/16 in. screws in the holes closest the side

of the ﬁreplace.

WARNING

HOT GLASS WILL CAUSE BURNS.

DO NOT TOUCH GLASS UNTIL COOLED.

NEVER ALLOW CHILDREN TO TOUCH GLASS.

•Install only when fireplace is OFF and COLD.

•Fireplace surfaces get EXTREMELY HOT!

•The glass on the front of the fireplace reaches EXTREMELY HIGH

temperatures and can cause severe burns if touched. Even after the

gas is turned off, fireplace surfaces remain extremely hot.

•Keep children away from an operating fireplace. Closely supervise

children in any room where a fireplace is operating to prevent

contact with glass.

P900005-07

f i r e - p a r t s . c o m

INNOVATIVEHEARTHPRODUCTS•SIGNATURE

SERIESDIRECT-VENTGASFIREPLACES•ENVY/ENVYCD35/40/45TEN•INSTALLATIONINSTRUCTIONS

P/N 900005-07 Rev. A 10/2014

1508 Elm Hill Pike, Suite 108

Nashville, TN 37210

IHP.US.com

Innovative Hearth Products reserves the right

to make changes at any time, without notice,

in design, materials, speciﬁcations, prices and

also to discontinue colors, styles, and products.

Consult your local distributor for ﬁreplace

Innovative Hearth Products, LLC.

P900005-07

Figure 2: Attaching the right side framing standoff

Screws

3. Align the left side of the framing standoff with the left side of

the ﬁreplace (Figure 3). Secure the standoff with two (2) of

the included 5/16 in. screws in the holes closest the side of

the ﬁreplace.

NOTE: The ends of the framing standoffs will overlap.

Figure 3: Attaching the left side framing standoff

Screws

4. Position the center support as shown (Figure 4), with

the larger screw holes oriented to the bottom. Secure

with two (2) of the included 5/16 in. screws in the top

and two (2) 5/16 in. screws in the bottom of the center

support.

Figure 4: Installing the center support

Screws

TOP VENT ROPE GASKET INSTALLATION INSTRUCTIONS

1. Slide the rope gasket over the top vent component and

position it snugly against the apppliance (

Figure 5).

Figure 5: Installing the rope gasket

Rope Gasket

AFTER INSTALLING THE KIT

1. Reinstall the media/logs (if applicable) and the glass door.

2. Refer to the Installation Instructions (P/N 900005-00)

for information regarding turning ON the gas supply,

reconnecting the power supply at the circuit breaker, and

additional framing information.

f i r e - p a r t s . c o m

Astria Fireplaces 900005-07 Installation guide

Astria Fireplaces 900005-07 Installation guide

Astria Fireplaces 900005-07 Installation guide

Related papers

Other documents