Audio enhancement Achiever Instruction And Installation Manual

Brand: Audio enhancement

Model: Achiever

Type: Instruction And Installation Manual

This manual is also suitable for

Product Instruction and

Installation Manual

Precautions for Installing the Infrared Receiver and Infrared Receiver/Amplier

Infrared Receiver and Infrared Receiver/Amplier will produce small amounts of heat. Provide

a minimum of 10 cm (4 in.) when installing the amplier close to the ceiling or wall. Infrared

Receiver and Infrared Receiver/Amplier are for indoor use only. They cannot be installed and

used in any of the situations below:

• In a place where they can get wet

• Where chemicals are used including under the eaves (ex. pool)

• Places that contain high amounts of steam, oil, or a ammable atmosphere

• Places where radiation, such as X-ray, high radio waves or magnetism are present

• On the ocean, beach or near hot springs (where corrosive gases would be present)

• In a place where high levels of vibration are present such as on a vehicle, or marine vessel

When using the provided bracket, note the following points:

• Select a sturdy wall to install

• Ensure that the appropriate fasteners or screws are used, and that they are rated appropriately

for the load they will be required to carry

• Ensure that all the directions from the manufacturer of the anchor, fastener or screws are

followed

• Do a visual check and make sure that nothing is unsteady and the screws are tight

Note the following points when tightening bolts and screws:

• Proper torque must be applied to all bolts and screws

• A torque wrench or a torque driver are required to set the proper torque

• It is dicult to get the proper torque with an impact driver or electric driver even if it has a

clutch; therefore, they should not be used as they may damage parts for installation

Note the following points when installing the Ultimate IISE Infrared Receiver/Amplier into

a rack:

• When mounting to a rack, remove the rubber feet from the base of the unit

• When installing near other heat-sensitive equipment, install the other equipment lower

than the receiver/amplier system

• Install rack in such a manner as to provide for sucient airow to maintain a temperature

of no more than 40 °C (104 °F) in the rack

Precautions for Installation

More than

10cm (4 in.)

than

10cm

than

10cm

Front

side

Installing the Bracket

Installing MTBR-07S Bracket for the Achiever, Elite II, IR-2007 or RA101 Receiver/Amplier.

Please carefully read the following assembly, installation and safety instructions before

installing the MTBR-07S Bracket for the Achiever, Elite II, IR-2007 or RA101 Receiver/

Amplier.

1. Installation Surface: The enclosed accessories are suitable only for attaching to walls made

of solid concrete or wood studs. Do not install to sheet rock or wood panel.

2. Tighten all the nuts using appropriate wrench.

3. Make sure that MTBR-07S Bracket is installed so the tray is above average head height and

does not disturb free movement in hallways.

4. You must test the MTBR-07S Bracket before setting the receiver/amplier.

5. The maximum weight allowed on the mount is 55 lbs. (0.024947 mt).

6. Check that the receiver/amplier is securely fastened to the bracket so it will not fall forward.

7. One month after installation and every six months after that, check that MTBR-07S Bracket

is securely fastened to the wall and the screws and nuts are not loose. In case of weakening,

remove the receiver/amplier, and strengthen all the points that have weakened.

8. Before reinstalling MTBR-07S Bracket, remove the receiver/amplier and then remount

according to the manual instructions.

The Achiever, Elite II, IR-2007 and RA101 Receiver/Amplier on the MTBR-07S

Install the Achiever, Elite II, IR-2007 and RA101 Receiver/Amplier as described below.

1. Fix the main unit to the bracket. Use 2 screws to x the bracket to the side of the main unit.

The torque for the screws is 1.18 N*m±0.2 N*m (12 kgf* cm ±2 kgf* cm).

2. Fix the adjustment bolts. The torque for the screws is 1.18 N*m±0.2 N*m (12 kgf*cm±2

kgf*cm).

3. After installation, make sure nothing is loose. Do a visual check and make sure that nothing

is unsteady and the screws are tight.

4. Fix the wire loop to the wall.

Warning for the Installation of the Bracket

Fix the bracket and the wire loop to the wall.

Please ensure the installation is securely attached to the wall.

Wire Loop Requirement:

• Diameter: more than φ in.

• Material: High carbon steel wire rods

[Caution]

Conrm there is enough strength in the wall to support the infrared receiver/amplier with the

bracket. Do not install it in plasterboard. Reinforce it when strength is insucient. Secure the

AC adapter as follows when it is required to be installed higher than 30 in. from oor.

• Use metal tie-wrap and tie up the two parts with something secure:

1. The brick of the AC adapter (make sure to tie it using more than two tie wraps apart

from each other)

2. Direct Current (DC) side cable at a very close point to the brick.

Installing the Bracket

Main Unit

MTBR-07S

Bracket

Screw

(provided)

Screw

(provided)

Adjustment bolt

Wire Loop

To the Wall

This is an excerpt from product manual DC-40082.01 by

To read the full manual, download the Audio Enhancement Product Manual from our Resources page

Audio enhancement Achiever Instruction And Installation Manual

Brand: Audio enhancement

Model: Achiever

Type: Instruction And Installation Manual

This manual is also suitable for

Download PDF

report

Audio enhancement Achiever Instruction And Installation Manual

This manual is also suitable for

Audio enhancement Achiever Instruction And Installation Manual

Other documents