Alma FLEXICOMPT AUTONOME+ Operating instructions

Brand
Alma
Model
FLEXICOMPT AUTONOME+
Type
Operating instructions
This document sketches out the main menus (please refer to operating manual MU 7033 EN for further information).
Document available for sotware 434v2.00
FORM DOC 124 A
OPERATING GUIDE
FLEXICOMPT AUTONOME+
GU 7033 EN I
www.alma.alma.fr
USING THE BUTTONS
Come back to the previous stage
- Choose the menu option
- Display the delivery information
- Validate the displayed option
- Validate a fault
Light the display during 10 seconds
Reset the volume and record the last
measurement data
SuPErVi
Unloading control
Visualization (Last measurement, Totalisers, Memorizing)
Supervisor Menu (Calibration, Season, Parameters, Maintenance,
OPTION transfer of parameters)
MEtErin
ViSuALi
NB1: If it’s used with Adblue, the FLEXICOMPT AUTONOME+ must be rinsed with water after use
NB2: Since the CTD+ key is not ATEX, it must be used outside potentially explosive area
NB3: Do not plug the USB cable during data transfer.
MEANING OF SYMBOLS
Optional action (depends on configuration choosen)
Mandatory action
Event during delivery
Action by operator
GU 7033 EN I
FORM DOC 124 A
UNLOAD A PRODUCT
3. CARRY OUT THE UNLOADING
4. FINISH THE UNLOADING OF A PRODUCT
1. CONNECT THE FLEXICOMPT AUTONOME+
START THE UNLOADING
16
L
Install the
FLEXICOMPT AUTONOME+
on the compartment
valve (respect the slope and rotation angles – see picture
on page 1)
2. PREPARE THE UNLOADING
CHOOSE THE PRODUCT
The choice of the
product is validated
when metering starts
0
L
GASoiL
0
L
unLE_LS
GASoiL
*
* last unloaded product
RESET THE METER
ErASinG
0000000
Open the valve
0
L
GASoiL
5. REMOVE THE FLEXICOMPT AUTONOME+
Disconnect the hose between the
FLEXICOMPT
AUTONOME+
and the reception tank
Remove the
FLEXICOMPT AUTONOME+
from the
compartment valve
CHECK THE CHOSEN PRODUCT
INTENTIONAL INTERRUPTION OF THE UNLOADING
THE COMPARTMENT IS EMPTY
The unloading may be interrupted by several situations
2001
L
Close the valve
Wait the blinking display
End the unloading (§4)
Continue with another
compartment by moving the
FLEXICOMPT AUTONOME+
(§3)
The unloading may be interrupted at any time by
closing the valve
5000
L
GASoiL
End the unloading (§4)
Continue with another
compartment by moving the
FLEXICOMPT AUTONOME+
(§3)
Close the valve
Alarm
GAS
980
L
Alarm
Validate the fault with
See list of alarms page 4
APPEARANCE OF A FAULT AND DISPLAY OF AN ALARM
DISPLAY THE DELIVERY INFORMATION
13,4
°C
41,6
m
3
/h
Instantaneous flowrate
Temperature
(with active option)
0
L
diESEL
0
L
unLEAdE
Current volume
(0 if reset with RAZ)
GASoiL
Clean the filter if necessary
6. END THE DELIVERY
Put back the
FLEXICOMPT AUTONOME+
in its box
0
L
0
L
or
volume at temperature:Vm
converted volume:Vb
...
1 - Continue with another compartment with the same product
(§3)
2 - Continue with another compartment with another product:
end the unloading (§4) and start a new one (§1)
3 - End the unloading: reset the meter (§4), remove the
FLEXICOMPT AUTONOME+
(§5) and end the delivery (§6)
WHAT DO YOU WANT TO DO?
Connect the hose between the
FLEXICOMPT AUTONOME+
and the reception tank
If it’s used with Adblue, the
FLEXICOMPT AUTONOME+
must be rinsed with water after use in order to clean it
and to ensure it works properly
SAvinG
0000000
If data recording is automatic, appearance of flowrate causes
a display test and resets the volume to zero.
RESET THE METER
RAZ du volume
NOTE: The unit of flowrate and volume depends on the
settings chosen.
GU 7033 EN I
FORM DOC 124 A
DISPLAY/TRANSFER* THE DELIVERY DATA
VISUALIZATION OF THE LAST DELIVERY RESULTS - sub-menu MEtErin
In case of a dispute,
those indications provide proof
VISUALIZATION OF ALL THE DELIVERY RESULTS - sub-menu MEMoriS
8669
L
GASoiL
MEtErin
ViSuALi
In case of a dispute,
those indications provide proof
MEMoriS
Display all the delivery details
recorded from the newest to the
oldest
Display a specific delivery
details, by entering the date
8669
L
GASoiL
MEtErin
ViSuALi MEtErin
LiSt
SELECt
The following details are displayed: date, measurement No. and
time, name of product, volume at temperature (Vm), converted
volume (Vb)
1
, average flowrate, measured volume of gas (for
information), temperature
1
,
density
1
.
VISUALIZATION OF THE TOTALISERS - sub-menu totALiS
8669
L
GASoiL
MEtErin
ViSuALi
In case of a dispute,
those indications provide proof
Display the totaliser
(volume at temperature)
Vm
Vb
Display the totaliser
(converted volume)
(with active option)
MEtErin
*
OPTION KEY CTD+: TRANSFER MEASUREMENT DATA
MEtErin
ViSuALi
SuPErVi
+
*
OPTION KEY CTD+: TRANSFER MEASUREMENT DATA - sub-menu trAnSFr
0000
L
GASoiL
totALiS
MEtErin
trAnSFr
CALibrA
x4
ConFiG
nb_dAYS
Transfer the parameters and the
measurements results to the key
Set the number of days for the
transfer of the measurement results.
All measurements over the last N
days will be transferred
Transfer the parameters and the measurement
results to the key
x2
The key must be placed on the UNI as shown below and outside potentially explosive area
0000
L
GASoiL
(
1
with active option)
19.3
°C
Average temperature of the product
tEMPErA
Density of the product (kg/m
3
)
VM tF 830
(with active option)
tiME
15h43
Volume at temperature
Converted volume
Vm
Vb
MASS 412
499
L
(with active option)
497
L
Product name
GASoiL
The key must be placed
on the UNI as shown:
Use the key outside potentially explosive area.
Do not plug the USB cable during data
transfer.
GU 7033 EN I
FORM DOC 124 A
LIST OF ALARMS
DISPLAY MEANING ACTION
FLoV_ Flow setting fault Check the parameters
FrEQ_ Frequency fault Check the parameters
COEFF_ Difference between two coefficients is greater than 0,5% Check the coefficients setup
MEtEr Problem of metering with the meter Check the setup
LoW_FLo
HiGH_FL
Flow rate less than the setting minimal flow rate
Flow rate greater than the setting maximal flowrate
Check the hydraulic configuration and the flowing
Check the setup
dAtE Loss of date and time Set date and time in metrological mode
GAS GDh is wet but GDl is dry Check the hydraulic configuration / Check the detector status
SEnSor1
SEnSor2
High gas detector fault (GDh)
Low gas detector fault (GDl) Use the maintenance menu to check the status of the detector
CoiL Loss of pulse transmitter signal Check the connection with the pulse transmitter
tEMPErA Temperature less than -20°C or greater than 50°C Check the temperature sensor (measure and calibration)
diSPLAY
doG
LCD display fault
Fault with card
If steady alarm, substitution of the UNI
If steady alarm, substitution of the UNI
ProGrAM
rAM
Error on the checksum of the metrological data
Saved memory fault
If steady alarm, substitution of the UNI
If steady alarm, substitution of the UNI
MEMoriS Bad writting into the memory If steady alarm, substitution of the UNI
FuLL
If a measurement result, not older than 3 months, is about to be
erased
If steady alarm, substitution of the UNI
oVErFLo Volume greater than 4 194 304 liters Reset the device
MEtro_ Configuration loss If steady alarm, substitution of the UNI
bAttErY Low battery Substitution of the batteries
totAL_ Totaliser fault If steady alarm, substitution of the UNI
dEF_MEM Loss of backup data concerning the last measurement If steady alarm, substitution of the UNI
Use the maintenance menu to check the status of the detector
REPARATOR USER
LF_HiGH Flow greater than 20m
3
/h while GDh dry Check the setup
drY MEt
When using a pump. The volume of gas is greater than the
minimum measured quantity
Stop metering
dEF_CoM Communication fault with IRDA link Check the IRDA link
rECEPt Check the compatibility
Problem of communication protocol between the calculator-
indicator UNI and the CTD+ key
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Alma FLEXICOMPT AUTONOME+ Operating instructions

Brand
Alma
Model
FLEXICOMPT AUTONOME+
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents