Bunker Hill Security Security Camera 95154 User manual

Brand: Bunker Hill Security

Model: Security Camera 95154

Type: User manual

This manual is also suitable for

95154

IMITATION DOME CAMERA With LED

ASSEMBLY AND OPERATING INSTRUCTIONS

95154

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

2006 by Harbor Freight Tools

contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight

Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual

product may differ slightly from the product described herein. Tools required for assembly and service may not

be included.

For technical questions or replacement parts, please call 1-800-444-3353.

Revised Manual 09k

Page 2SKU 95154

For technical questions, please call 1-800-444-3353

SPECIFICATIONS

Batteries Required 1.5V DC “AA” Batteries (Qty. 2)

(not included)

Overall Dimensions 4-5/8” D X 3” H

Imitation Camera

Angle

360° Left/Right Rotation

Fixed 45°

Mounting Hole Spacing

Unit Weight

.3 Lbs.

Save This Manual

You will need the manual for the safety warnings and precautions, assembly instructions,

operating and maintenance procedures, parts list and diagram. Keep your invoice with this

manual. Write the invoice number on the inside of the front cover. Keep the manual and

invoice in a safe and dry place for future reference.

SAFETY WARNINGS AND PRECAUTIONS

WARNING: When using this product, basic safety precautions should always be followed

to reduce the risk of personal injury and damage to equipment.

Read all instructions before using this product!

1. Keep work area clean and well lit. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use the Imitation Dome Camera in damp or wet

locations. Don’t expose to rain. Do not use electrically powered products in the presence

of ﬂammable gases or liquids.

3. Keep children away. Children must never be allowed in the work area. Do not let them

handle the Imitation Dome Camera. This product is not a toy.

4. Use the right product for the job. Do not modify this product and do not use this product

for a purpose for which it was not intended.

5. Dress properly. Protective, electrically non conductive clothes and nonskid footwear

are recommended when working. Wear restrictive hair covering to contain long hair.

6. Use eye protection. Always wear ANSI-approved impact safety goggles during

installation.

7. Maintain with care. Keep the Imitation Dome Camera clean for better and safer

performance.

2.659” (67.59 mm) center to center

Page 3SKU 95154

For technical questions, please call 1-800-444-3353

8. Stay alert. Watch what you are doing, use common sense. Do not install the Imitation

Dome Camera when you are tired.

9. Check for damaged parts. Before using the Imitation Dome Camera, any part that

appears damaged should be carefully checked to determine that it will operate properly

and perform its intended function. Check for alignment and binding of moving parts;

any broken parts or mounting ﬁxtures; and any other condition that may affect proper

operation. Any part that is damaged should be properly repaired or replaced by a qualiﬁed

technician. Do not use the Imitation Camera Dome if the power switch does not turn the

Camera Dome on and off properly.

10. Replacement parts and accessories. When servicing, use only identical replacement

parts. Use of any other parts will void the warranty. Only use accessories intended for

use with this product. Approved accessories are available from Harbor Freight Tools.

11. Do not install the Imitation Dome Camera if under the inﬂuence of alcohol or drugs.

Read warning labels if taking prescription medicine to determine if your judgment or

reﬂexes are impaired while taking drugs. If there is any doubt, do not install the unit.

12. Only use 1.5V DC AA-Batteries. Always properly dispose of used batteries in accordance

to the guidelines for waste disposal in your community.

13.

UNPACKING

When unpacking, check to make sure that the product is intact and undamaged. If any

part are missing or broken, please call Harbor Freight Tools at: 1-800-444-3353

The warnings, precautions, and instructions discussed in this instruction manu-

al cannot cover all possible conditions and situations that may occur. It must be

understood by the operator that common sense and caution are factors which

cannot be built into this product, but must be supplied by the operator.

WARNING: All batteries must be disposed of properly. Do not incinerate. Batteries

may burst, causing personal injury and/or property damage. Dispose of the used bat-

teries properly, as cadmium in the batteries is toxic. For disposable guidelines, check

with your local waste management guidelines in your community.

14.

BATTERY INSTALLATION

1. First, remove the battery cover by pressing in on the upper lip of the cover then pull it

out.

2. Next place two AA 1.5 VDC Batteries in the Battery Housing. Be sure that the polari-

ties (+ or -) of the batteries line up with the polarity signs in the battery housing. Finally

replace the battery cover. See Figure 1 on page 4.

Page 4SKU 95154

For technical questions, please call 1-800-444-3353

1. Chose a wall or ceiling location that allows you to mount the unit onto a solid surface

capable of sustaining the weight of the unit. It is recommended that you choose a location

that is out of the reach of pedestrians. If you cannot mount the camera to a wall stud, you

will need to use the Dry Wall Mounting Anchors and Wood Screws (both not included).

2. It is essential to proper mounting that you use the correct size screws and that you also

space the two screw correctly. The exact distance between the two screws is 2.659”

(67.59 mm) center to center. You can make a pattern of the mounting holes by placing

a piece of tracing paper over the back of the Imitation Dome Camera and trace the

mounting holes location using a pen or pencil. Next tape the pattern over the area that

you want to install the camera. Mark the center of each mounting hole by hammering

a nail through the pattern into the mounting surface. Attach the screws to the mounting

surface leaving about a 1/4” of the screws’ shanks exposed.

Warning: When mounting, be sure to avoid hammering into any electrical wiring.

3. After the two mounting screw have been attached to the wall or ceiling, place the two

mounting holes on the camera over the screw heads. Press the Dome Camera over the

screw heads and twist the camera. This should secure it into place. Always be careful,

when drilling into a wall or ceiling, to avoid wires, pipe or cables that may be in the path

of the drill. Be aware that the Camera needs to be mounted securely so it will not fall off

the mounting and cause bodily injury.

Note: The mounting holes on the Imitation Dome Camera are approximately 1/4” with 5/32”

slots. See Figure 4 below.

OPERATION

Once the two AA batteries are installed in the Dome Camera, the LED light will

automatically blink in 5 second intervals until the batteries go dead. When the light stops

blinking, replace the batteries.

CAMERA INSTALLATION

FIGURE 1

Battery Housing

Mounting Holes

Note: There are no replacement parts available for this product.

Bunker Hill Security Security Camera 95154 User manual

Brand: Bunker Hill Security

Model: Security Camera 95154

Type: User manual

This manual is also suitable for

95154

Download PDF

report

Bunker Hill Security Security Camera 95154 User manual

This manual is also suitable for

Bunker Hill Security Security Camera 95154 User manual

Related papers

Other documents