GB
INSTALLATION GUIDE
•
Read this “INSTALLATION GUIDE” before operating.
•
Keep this “INSTALLATION GUIDE” for future reference.
•
Read the general recommendations about disposing of packaging in the
Instructions for use.
NOISE, EXCESSIVE VIBRATIONS AND WATER LEAKAGES
CAN BE CAUSED BY INCORRECT INSTALLATION.
NEVER MOVE THE APPLIANCE BY CARRYING IT AT THE
WORKTOP.
IL
10600832.fm Page 1 Tuesday, October 24, 2006 5:08 PM
Black process 45.0° 130.0 LPI
2
PARTS SUPPLIED
•
Package with small items
●
●
•
Instruction for use
●
●
•
4 plastic caps (for certain models, the plastic caps
are attached to the back of the appliance)
●
●
•
Wrench
●
●
•
Inlet hose (inside the machine or already installed)
●
●
•
“U”-bend (inside the machine or already installed)
●
●
A
B
C
D
E
10600832.fm Page 2 Tuesday, October 24, 2006 5:08 PM
Black process 45.0° 130.0 LPI
3
REMOVE TRANSPORT BOLTS!
Important: Not removed transport bolts cause damages to the appliance.
Unscrew the four screws (see arrows) with the wrench
C
supplied.
Only if the transport bolts' positions look as on the left sketch below: move the screws to the
centre of the holes.
Pull out the screws together with the coloured plastic spacer.
1
2
3
10600832.fm Page 3 Tuesday, October 24, 2006 5:08 PM
Black process 45.0° 130.0 LPI
4
To seal the holes either:
- insert the supplied plastic caps
B
supplied in the wide part of the hole and slide them in the
direction of the arrow until they click into place (see picture I)
OR (depending on the model):
- push the plastic caps attached on the back of the appliance on the holes (see picture II).
Important:
If you have a washing machine with the drain hose inside the appliance (see “CONNECT
THE DRAIN HOSE”, picture 10 / II), pull out the drain hose BEFORE removing the transport
bolts, otherwise you risk to damage the drain hose inside the machine while moving the
appliance to its final position.
Keep the transport bolts and the wrench for further transporting of the appliance and in this
case refit the transport bolts in reverse order.
4
III
10600832.fm Page 4 Tuesday, October 24, 2006 5:08 PM
Black process 45.0° 130.0 LPI
5
ADJUSTMENT OF THE FEET
The appliance must be installed on a solid and level floor surface (if necessary use
a spirit level). If the appliance is to be installed on a wooden or floating floor,
distribute the weight by placing it on a 60 x 60 cm sheet of plywood at least 3 cm
in thickness and secure it to the floor. If the floor is uneven, adjust the 4 levelling
feet as required; do not insert pieces of wood etc. under the feet.
Slacken the locknut clockwise (see arrow) using the wrench
C
supplied.
Lift slightly the machine and adjust the height of the foot revolving it.
Important:
tighten the locknut by turning it anti-clockwise towards the appliance casing.
5
6
7
10600832.fm Page 5 Tuesday, October 24, 2006 5:08 PM
Black process 45.0° 130.0 LPI
6
CONNECT THE WATER SUPPLY INLET HOSE!
If the water inlet hose is not already installed, it must be screwed to the appliance.
Screw by hand the inlet hose
onto the tap tightening the nut.
Attention:
• no kinks in the hose!
• The appliance
must not
be connected to the mixing tap of an un-pressurized
water heater.
• Check water-tightness of connections by turning the tap completely on.
• If the hose is too short, replace it with a suitable length of pressure resistant hose
(1000 kPa min, EN 50084 approved type).
• Check the inlet hose regularly for brittleness and cracks and replace if necessary.
• The washing machine can be connected without a non-return valve.
For models with Water Stop hose:
If the flexible hose is too short, replace it with a 3 m Water Stop hose (available from After-Sales
Service or from your dealer). This replacement is only to be carried out by a trained electrician.
Depending on the model, the inlet hose and the plastic enclosure at the tap connection contain
electrical components.
Do not cut the hose and do not immerse the plastic enclosure in
water
. Isolate the appliance from the mains immediately if the hose is damaged.
8
9
10600832.fm Page 6 Tuesday, October 24, 2006 5:08 PM
Black process 45.0° 130.0 LPI
7
10600832.fm Page 7 Tuesday, October 24, 2006 5:08 PM
Black process 45.0° 130.0 LPI
8
CONNECT THE DRAIN HOSE
I. In case the drain hose is installed as shown on the models below:
Unclip it from the holders marked with arrows.
.I
II. In case the drain hose is instaled inside the washing machine:
Pull the hose completely out of the holder and close the opening with cap
a
.
DO NOT START THE WASHING MACHINE BEFORE HAVING PULLED OUT AND
CONNECTED THE DRAIN HOSE!
.II
III. In case the drain hose is installed in the upper part of the washing machine:
Unclip it from both holders (see arrows).
.III
10
1
2
a
10600832.fm Page 8 Tuesday, October 24, 2006 5:08 PM
Black process 45.0° 130.0 LPI
9
Fit the “U” bend
E
, if not already installed,
at the very end of the drain hose
.
Important:
Do not fix the “U” bend to another position of the drain hose, otherwise there
might be the risk of simultaneous filling and draining of the machine (“siphoning effect”).
Notes:
•
Make sure there are no kinks in the drain hose.
•
Secure the hose so that it cannot fall down.
•
Small hand basins are not suitable.
•
To make an extension use a hose of the same type and secure the connections with clips.
•
Max. Overall drain hose length: 2,50 m (in this case, the maximum height for fixation - see
picture below - is 90 cm).
11
E
10600832.fm Page 9 Tuesday, October 24, 2006 5:08 PM
Black process 45.0° 130.0 LPI
5019 106 00832
ELECTRICAL CONNECTION
Use a socket with an earth connection.
Do not use extension leads or multi sockets.
The electrical power cable must be replaced exclusively by a licensed electrician.
Electrical connections must be made in accordance with local regulations.
10600832.fm Page 10 Tuesday, October 24, 2006 5:08 PM
Black process 45.0° 130.0 LPI
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Whirlpool AWO 9365 Installation guide
-
Whirlpool WA 3862 Installation guide
-
Whirlpool WAK 1400 EX/4 Installation guide
-
-
Whirlpool WA PL 962 BW Owner's manual
-
Whirlpool WAK 7114 User guide
-
LADEN PWF 1726 User guide
-
Whirlpool AWOE 8559 User guide
-
Whirlpool WAGH 81 Owner's manual
-
Whirlpool AWOC 7221 Installation guide