jbc MN User manual

MN
jbc
Brand
jbc
Model
MN
Type
User manual

jbc MN is a Nitrogen Regulator Module designed to minimize gas consumption while soldering with nitrogen. Connected to a compatible soldering station, it controls the flow of nitrogen gas, releasing it when the tool is removed from the stand and stopping when it's returned and reaches sleep temperature. Adjustable flow rate (0.5-3.5 SLPM at 5 Bar) and a maximum pressure of 6 bar.

jbc MN is a Nitrogen Regulator Module designed to minimize gas consumption while soldering with nitrogen. Connected to a compatible soldering station, it controls the flow of nitrogen gas, releasing it when the tool is removed from the stand and stopping when it's returned and reaches sleep temperature. Adjustable flow rate (0.5-3.5 SLPM at 5 Bar) and a maximum pressure of 6 bar.

MN
Nitrogen Regulator Module
for DI Control Unit
www.jbctools.com
INSTRUCTION MANUAL
Nitrogen Gas Circuit Electric Circuit
DI
Control Unit
DNS
Stand for Nitrogen
Handles
T245N
Nitrogen General Purpose
Handle
MN
Nitrogen Regulator
Module
Power
Cord
Socket
GN
Nitrogen Generator
Module
Compressed
Air Inlet
or
Handle
N2 tube
from N2 net
Module Cable
Connector
Ref. 0026830
Stand Cable Connector Ref. 0024227
N2 pressure range
supply 3 to 6 bar
6 bar MAX
Packing List
Connection
The following items are included:
Nitrogen Regulator Module
........................................... 1 unit
Module Cable
Connector ...................... 1 unit
Ref. 0026830
Manual ............................. 1 unit
Ref. 0031026
This manual corresponds to the following reference:
MN-A
2
Main menuMain menu
Exit
1 Reset settings
2
Station settings
3
Tool settings
Station settingsStation settings
1 Temp unit
Celsius
2
Maximum temp 400
0
C
3
Minimum temp 200
0
C
4
Nitrogen mode ON
N2 outlet
Description
The MN is an electrovalve controlled by the soldering station that allows you to solder with nitrogen
with a minimum gas consumption.
Once the MN (Nitrogen Regulator Module) has been connected to the Control Unit, enter into the
Station Settings menu and switch on the Nitrogen Mode.
The module will let the gas flow when taking out the tool from the stand and turning off when the
tool is again placed in its stand and reaches the sleep temperature.
Connection to
soldering station
Recommended N2 flow:
1-2 liters/minute
N2 flow control
Pressure range supply
3-6 bar
Maximum pressure
6 bar
www.jbctools.com
3
This product should not be thrown in the garbage.
In accordance with the European directive 2002/96/EC, electronic equipment at the end of their life
must be collected and returned to an authorized recycling facility.
Manual in other languages available on our website
Warranty
JBC’s 2 year warranty covers this equipment against
all manufacturing defects, including the replacement
of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must
be returned, postage paid, to the dealer where it was
purchased.
Register your warranty within 30 days of purchase
in www.jbctools.com/productregistration
0031026-010323
MN
Nitrogen Regulator Module for DI Control Units
Ref.: MN-A
- Weight: 1,142 kg (2.51 lb)
- Dimensions: 50 x 120 x 130 mm (1.97 x 4.72 x 5.12 in)
- Voltage (AC): 24V (from control unit)
- Power: 3W
- N2 flow regulation: 0,5 - 3,5 SLPM (5 Bar)
- Max. Pressure 6 bar
- Ambient operating temperature: 10 - 40 ºC (50 - 104 ºF)
Complies with CE standards.
ESD Safe.
Specifications
www.jbctools.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

jbc MN User manual

MN
jbc
Brand
jbc
Model
MN
Type
User manual

jbc MN is a Nitrogen Regulator Module designed to minimize gas consumption while soldering with nitrogen. Connected to a compatible soldering station, it controls the flow of nitrogen gas, releasing it when the tool is removed from the stand and stopping when it's returned and reaches sleep temperature. Adjustable flow rate (0.5-3.5 SLPM at 5 Bar) and a maximum pressure of 6 bar.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents