INSTALLATION INSTRUCTIONS
External Media Compartment Installation Instructions
Compatible with Shade Series 2™ 55-inch, 65-inch, and 75-inch TVs
(models: SHD2-55, SHD2-65, SHD2-75)
TOOLS REQUIRED
Phillips Head #3 Screwdriver
Allen Wrench, 5/32-inches
1. Use a Philips #3 screwdriver to unscrew the four ¼-20 screws and remove the cover from the
External Media Compartment.
2. The hardware kit that includes two stake adapters and six screws will be located inside of the
External Media Compartment. Remove the hardware kit and place your desired media devices in the
compartment. Wires from the media devices should exit the media compartment by the foam gasket.
3. Use the four ¼-20 screws that were previously removed in step 1 to re-aach the cover to the
External Media Compartment
INSTALLATION INSTURCTIONS: EXTERNAL MEDIA COMPARTMENT
Information is subject to change without notice.
© 2021 Séura
1230 Ontario Road, Green Bay, Wisconsin 54311
1-800-957-3872 contacts@seura.com
www.seura.com
#94-069001
1230 Ontario Road Green Bay, Wisconsin 54311
1-800-957-3872 contacts@seura.com
www.seura.com
Publish date: November 17, 2021. Information is subject to change without notice.
© 2021 Séura
4. Locate the two stake pocket adapters and four screws that came in the hardware kit. Line up the stake
pocket adapters with the correct set of holes on each wing. There are two sets of holes on each wing: the
inside set of holes is for Shade Series 2™ 55-inch and 65-inch TVs and the outside set of holes is for the
Shade Series 2™ 75-inch TV. Using an Allen wrench and the four provided screws, screw the stake pocket
adapters in place. Leave these screws a lile loose to allow adjust-ability – you’ll tighten them later.
5. Place the Shade Series 2™ TV in a safe position for mounting the External Media Compartment to the
back of the TV. We recommend laying the TV face-down on a flat, so surface.
6. Align the stake pocket adapters on the External Media Compartment with the stake pocket holes located
near the boom of the Shade Series 2™ TV. Slide the compartment into position and tighten the four
screws from step 4.
7. Insert two ¼-20 screws through the holes on the back of the TV and into the stake pocket adapters to
aach the adapters to the back of the TV.
8. Open the main A/V compartment on the back of the Shade Series 2 TV and make wiring connections
from the media devices in the External Media Compartment to the inputs located in the main media
compartment on the Shade Series 2 TV. Close the A/V compartment and test unit to verify functionality.
INSTALLATION INSTURCTIONS: EXTERNAL MEDIA COMPARTMENT
1230 Ontario Road, Green Bay, Wisconsin 54311
1-800-957-3872 contacts@seura.com
www.seura.com
Information is subject to change without notice.
© 2021 Séura
#94-069001
Séura is not liable for damage or destruction to third party devices used with Séura products. If using an IR device (for example, Apple TV and Roku models prior to 2019), you will need to set up CEC control for your
streaming device. This option is available in the settings menu of your streaming device. To enable CEC on your Séura TV, go to Menu – Network – Advanced Network Setting – CEC. This allows you to use Séura’s TV
remote to control the streaming device. If your streaming device does not use an RF connection and is not CEC compatible, then it will not receive remote control commands when placed in the media compartment. An
IR emitter may work in getting a signal to the streaming device.
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Seura Shade Series 2 SHD2-55 User manual
-
Seura FS-1 Owner's manual
-
-
-
-
-
-
-
-
Other documents
-
PTN SHD2 User manual
-
GrowSpan 500 Series User manual
-
Leica DISTO PRO 4 Owner's manual
-
-
Carlton SP4012 Owner's manual
-
-
Honeywell TotalPlant LCN System Installation
-
ADB L-861SE User manual
-
Husqvarna 917299390 Owner's manual
-
Ozark Trail WMT-1410N User manual
