2. Conductix Wampfler
  3. Line Feed
Line Feed

Conductix Wampfler Line Feed User manual

  • Hello, I'm your chat assistant. I have reviewed the Installation Instructions for the CONDUCTIX Line Feed SingleFlexLine Program 0815. This document includes the technical specifications, step-by-step instructions for installation, and details about various components. I'm ready to assist you with any questions you have regarding this device.
  • What is the maximum current for the line feed?
    What cable cross-section is recommended?
    What is the minimum bending radius for the rail?
    What is the torque for the hexagon nut?
Installation Instructions
Line Feed
SingleFlexLine Program 0815
MV0815-0009b-EN
www.conductix.com original document page 1 of 7
Order Number:
08-E015-0570
Installation Instructions
Line Feed
SingleFlexLine Program 0815
MV0815-0009b-EN
www.conductix.com original document page 2 of 7
1 Technical Data
For straight and bended rails r ≥ 1000 mm
Imax = 54 A
Cable Cross Section = 4-6 mm2
2 Installation
Work steps:
1. Bend the rail to the desired radius (see BAL0800-0004).
2. Cut the insulation profile on the needed position.
3. Put the U-plate on the right position and drill a hole with Ø = 3.1 mm (one hole on each side with a staggered arrangement).
Notice: The holes (1) for the blind rivets are no through holes!
1
Installation Instructions
Line Feed
SingleFlexLine Program 0815
MV0815-0009b-EN
www.conductix.com original document page 3 of 7
4. Put a blind rivet at each side, notice a staggered arrangement.
5. Crimp the cable and cable lug.
6. Consider the required arrangement of small parts and fix it with the hexagon nut. Tighten the screw with 2 Nm.
All parts included in delivery!
Pos.
Description
1
Contact Plate Line Feed 0815
2
Blind Rivet Copper/Bronze Ø3x5 Flat Head
3
Cable Lug M4/6mm
2
4
Detent-Edged Washer SHB-K-D4,1-A4
5
Hexagon Nut DIN934-M4-A4
6
Power Feed Cover 0815 SP
6
5
4
2
1
3
Installation Instructions
Line Feed
SingleFlexLine Program 0815
MV0815-0009b-EN
www.conductix.com original document page 4 of 7
7. After the assembly it should be like following:
8. After the cable was connected, put the feed cap over the feeding point and consider the direction for the cable.
Installation Instructions
Line Feed
SingleFlexLine Program 0815
MV0815-0009b-EN
www.conductix.com original document page 5 of 7
9. Installation position (feed offset): Mount the power feeds with an offset
Installation Instructions
Line Feed
SingleFlexLine Program 0815
MV0815-0009b-EN
www.conductix.com original document page 6 of 7
10. Do not mount the power feeds directly next to the hanger clamp.
min. 100
min. 100
Installation Instructions
Line Feed
SingleFlexLine Program 0815
MV0815-0009b-EN
www.conductix.com original document page 7 of 7
Rheinstraße 27 + 33
79576 Weil am Rhein - Märkt
Phone: +49 (0) 7621 662-0
Fax: +49 (0) 7621 662-144
[email protected]
www.conductix.com
Importer for the United Kingdom:
Conductix-Wampfler Ltd.
1, Michigan Avenue
Salford
M50 2GY
United Kingdom
Phone: +44 161 8480161
Fax: +44 161 8737017
[email protected]
www.conductix.com
/