CONDUCTIX Program 0300 Installation guide

Program 0300
Brand
CONDUCTIX
Model
Program 0300
Type
Installation guide

CONDUCTIX Program 0300: The wind restraining damping device is designed to prevent the towing rope from being carried out sideways by strong lateral forces such as wind. It connects the towing rope to the cable package and is mounted between the two cable clamps. The device is easy to install and can be used with steel ropes with diameters of 8 to 10 millimeters. It features a plastic housing and set screws for clamping the towing rope. The device helps to ensure the safe operation of towing rope systems, especially in windy conditions.

CONDUCTIX Program 0300: The wind restraining damping device is designed to prevent the towing rope from being carried out sideways by strong lateral forces such as wind. It connects the towing rope to the cable package and is mounted between the two cable clamps. The device is easy to install and can be used with steel ropes with diameters of 8 to 10 millimeters. It features a plastic housing and set screws for clamping the towing rope. The device helps to ensure the safe operation of towing rope systems, especially in windy conditions.

Installation Instructions
Wind Restraining Damping Device
Program 0300
MV0310-0017d-EN
www.conductix.com Seite 1 von 4
Order Number
03
-D025-0096
Contents
1 Overview ........................................................................................................................................................................................ 1
2 Required tools ................................................................................................................................................................................ 1
3 Sequency of assembly works ......................................................................................................................................................... 2
1 Overview
The wind restraining damping device connects the towing rope to the cable package in order to prevent the towing rope from being
carried out sideways by strong lateral forces such as wind.
2 Required tools
socket wrench SW4
A wrench with a long arm is favorable because of the high torque needed.
Standard short wrench sockets are not suitable. A longer version is needed.
Wrench SW13
Loctite 243
Steel rope ∅ 8/10
Installation Instructions
Wind Restraining Damping Device
Program 0300
MV0310-0017d-EN
www.conductix.com Seite 2 von 4
3 Sequency of assembly works
The following steps insure that the wind restraining damping device is mounted at the right place, tightly and without damaging
the towing rope.
Mount the device when the festoon system is retracted.
To prevent it from falling down the device has to be fixed to the lower cable clamp with the two shackles. Secure the
shackles with Loctite 243.
Afterwards the wind restraining damping device is attached in the middle (based on the height) between the two cable
clamps to the towing rope.
Therefore the towing rope is inserted into the groove:
After that the towing rope is clamped slightly by the set screws. To reach the set screws the plastic housing
can be turned on the clamp by roughly 45°:
To reach the required clamping force the following process has to be followed (see flow chart on the next page).
The two set screws have to be at the same depth at any time ( ).
1 Find the reference point for tightening of the set screws:
1.1 Check if the clamp can be moved by hand in the direction of the towing rope.
If it is movable → go to step 1.2
If it is not movable → go to step 1.3
1.2 The set screws have to be tightened slightly.
→ Go back to step 1.1
1.3 Check if the clamp can be turned by hand around the axis of the towing rope.
If it is rotatable → go to step 2
If it is not rotatable → go to step 1.4
1.4 The set screws have to be untightened slightly.
→ Start again with step 1.1
2 Tighten the set screws by 2 ½ turns.
SW4
Installation Instructions
Wind Restraining Damping Device
Program 0300
MV0310-0017d-EN
www.conductix.com Seite 3 von 4
SW4
Installation Instructions
Wind Restraining Damping Device
Program 0300
MV0310-0017d-EN
www.conductix.com Seite 4 von 4
Conductix-Wampfler GmbH
Rheinstraße 27 + 33
79576 Weil am Rhein - Märkt
Germany
Phone: +49 (0) 7621 662-0
Fax: +49 (0) 7621 662-144
[email protected]
www.conductix.com
Importer for the United Kingdom:
Conductix-Wampfler Ltd.
1, Michigan Avenue
Salford
M50 2GY
United Kingdom
Phone: +44 161 8480161
Fax: +44 161 8737017
[email protected]
www.conductix.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

CONDUCTIX Program 0300 Installation guide

Program 0300
Brand
CONDUCTIX
Model
Program 0300
Type
Installation guide

CONDUCTIX Program 0300: The wind restraining damping device is designed to prevent the towing rope from being carried out sideways by strong lateral forces such as wind. It connects the towing rope to the cable package and is mounted between the two cable clamps. The device is easy to install and can be used with steel ropes with diameters of 8 to 10 millimeters. It features a plastic housing and set screws for clamping the towing rope. The device helps to ensure the safe operation of towing rope systems, especially in windy conditions.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents