2. Computers & electronics
  3. TVs & monitors
  4. Wall & ceiling mounts accessories
  5. Ranger design
  6. Ladder Rack Mounting Kit for Transit Connect
Ladder Rack Mounting Kit for Transit Connect

Ranger design Ladder Rack Mounting Kit for Transit Connect Installation guide

  • Hello! I've reviewed the Installation Guide for the 18-U0046 Mounting Track. This document provides instructions for installing the mounting track on Transit Connect vehicles, including assembly, and installation procedures. The guide also includes steps for modifying the kit for Nissan NV200. I'm ready to answer your questions about the product or installation process.
  • What tools are required for installation?
    What is the mounting track model number?
    Which holes on the roof are used for mounting?
INSTALLATION GUIDE
18-U0046 Mounting track
TransiT ConneCT LWB, TransiT ConneCT sWB
REAR FRONT
for TransiT ConneCT 104" WheeLBase
for TransiT ConneCT 120" WheeLBase
angLe pad angLe padsTraighT pad
For technical support, contact us at 1-800-565-5321 18-U0046 Installation Guide | REV. A3 | Page 2
QUICK START GUIDE
q 1.1.1 SeTup ( Verify aLL parTs are presenT )...............................................................................................
q 2.1.1 insTaLLaTion ( insTaLL The mounTing TraCk WiTh pads on The roof ).........................................................
2 To 3
4 To 5
Phase 1 - assembly
Phase 2 - Installation
2
PERSONS
PHASE 1 – ASSEMBLY
1.1 SETUP
1.1.1 Verify all parts are present.
10 - 753 10 - 750
10 - 732
Verify all Parts are Present
Item No. Description Qty.
10-732 mounTing TraCk 2
10-750 angLe pad 4
10-753 sTraighT pad 2
96-1032 CusTomer insTaLL fasTener kiT 1
REQUIRED ITEMS
qCordless Impact
qTape Measure
qLadder
q10mm Socket
qSilicone
For technical support, contact us at 1-800-565-5321 18-U0046 Installation Guide | REV. A3 | Page 3
fasTener Bags.
Fastener Assembly96-1032
Verify all Parts are Present
# 98-117 Flat Washer
5/16"
6×6×
Lock Washer
5/16"
# 98-123
6×6×
# 90-004
6×6×
Hex Bolt
M8-1.25 × 50mm
SS304
6×6× Neoprene Spacer
1/16" Thick
# 10-764
6× TransiT ConneCT
# 94-172
6×6×
Hex Serrated Nut
5/16"
ZINC #90-004 Hex Bolt M6 × 50mm
#98-123 LoCk Washer
#98-117 FLaT Washer
MounTing TraCk
Pad
#10-764 Neoprene spaCer
#94-172 Hex serraTed nuT
For technical support, contact us at 1-800-565-5321 18-U0046 Installation Guide | REV. A3 | Page 4
REAR
TOP VIEW
SIDE VIEW
FRONT
shoWing WhaT hoLes you WiLL use
shoWing The posiTion of The pads
angLe pad angLe padsTraighT pad
TOOLS
qCordless Impact
q13mm Socket
qSilicone
PHASE 2 – INSTALLATION
2.1 INSTALLATION
2.1.1 Install the mounting track with pads.
Transit connect 104" Wheelbase
NOTE: • Slide stud plate on both ends of the mounting track before insttalling the mounting track.
• Slide 3 stud plates if you have 3 bar racks.
NOTE: • Apply silicone Around eAch hole, And bolt
Then fasTen The TraCks To The roof.
•use The 1sT, 3rd, and 4Th hoLes of The roof
from The rear.
NOTE: use The 1sT, 3rd, and 4Th
hoLes of The roof
from The rear.
FASTENERS USED
6×
#90-004 Hex Bolt M6 × 50mm
#98-123 LoCk Washer
#98-117 FLaT Washer
MounTing TraCk
Pad
#10-764 Neoprene spaCer
Roof
#94-172 Hex serraTed nuT
SILICONE
For technical support, contact us at 1-800-565-5321 18-U0046 Installation Guide | REV. A3 | Page 5
Transit connect 120" Wheelbase
REAR
TOP VIEW
SIDE VIEW
FRONT
shoWing WhaT hoLes you WiLL use
shoWing The posiTion of The pads
angLe pad angLe padsTraighT pad
TOOLS
qCordless Impact
q13mm Socket
NOTE: • Slide stud plate on both ends of the mounting track before insttalling the mounting track.
• Slide 3 stud plates if you have 3 bar racks.
NOTE: • Apply A beAd of silicone Around eAch hole,
Then fasTen The TraCks To The roof.
•use The 1sT, 3rd, and 4Th hoLes of The roof
from The rear.
NOTE: use The 1sT, 3rd, and 4Th
hoLes of The roof
from The rear.
FASTENERS USED
6×
#90-004 Hex Bolt M6 × 50mm
#98-123 LoCk Washer
#98-117 FLaT Washer
MounTing TraCk
Pad
#10-764 Neoprene spaCer
Roof
#94-172 Hex serraTed nuT
For technical support, contact us at 1-800-565-5321 18-U0046 Installation Guide | REV. A3 | Page 6
“Congratulations, you have successfully installed your
Mounting Track on your vehicle!
Thank you for doing business with us.”
For any feedback or suggestions you might have, please contact: cs@rangerdesign.com
Transit connect 104" Wheelbase
Transit connect 120" Wheelbase
For technical support, contact us at 1-800-565-5321 18-U0046_NV Installation Guide | REV. A1
10-750
7 - 7/16"
2 - 1/4"
10-750
10-753
Mount rear shim to track with supplied bolt
in indicated slot.
• Measure and mark hole locations for front shim.
• Position the holes along the center of the track.
• Use a 1/4" drill bit and make 2 holes at the positions
indicated.
• Remove any burrs or sharp edges after drilling.
• Mount the front shim to the track with supplied bolt
in the indicated slot.
Mount middle shim to track with supplied
bolt in indicated slot.
qSafety Glasses
qTape Measure
qMarker
qCordless Drill
q1/4" Drill Bit
REQUIRED ITEMS
2
PERSONS
procedure to modify 18-u0046 mounting kit
for nissan nv200
/