SEQURE MSS12 Pro is a smart soldering station with a 1.14" LCD color screen that supports multiple power supply methods including PD2.0/3.0, QC2.0/3.0, DC12V-25V, and XT60 3S-6S, as well as AC100-240V. It features firmware upgrade capability, custom boot logo, changeable main interface color, and the ability to switch between Celsius and Fahrenheit. With intelligent temperature control, it can achieve a precision of plus or minus 1%.
SEQURE MSS12 Pro is a smart soldering station with a 1.14" LCD color screen that supports multiple power supply methods including PD2.0/3.0, QC2.0/3.0, DC12V-25V, and XT60 3S-6S, as well as AC100-240V. It features firmware upgrade capability, custom boot logo, changeable main interface color, and the ability to switch between Celsius and Fahrenheit. With intelligent temperature control, it can achieve a precision of plus or minus 1%.
MSS12P/MSS12 Pro
Intelligent Soldering
Station Instruction Manual
Thank you for using this product, please read the manual
carefully before use to avoid mistakes in your operation.
1.Product Overview
MSS12P/MSS12 Pro intelligent soldering station comes with 1.14-inch LCD color screen display, which supports
PD2.0/3.0, QC2.0/3.0, DC12V-25V, MSS12 Pro also support XT60 3S-6S, AC100-240V power supply methods.Firmware
upgrade, custom boot LOGO, change the color of the main interface,switch between Celsius and Fahrenheit, can
calibrate and compensate for temperature, and intelligent temperature control can reach up to plus or minus 1%.
2.Menu Introduction
Main Interface Level 1 Menu Level 2 Menu
Main
Interface
Icon
Display Icon Description Operation method
Stop
Work
Sleep
C-T
H-V
H-T
L-V
P-T
20.0V
300℃
Check Tip
High-V
High-T
Low-V
Pcb-T
300℃
Stop Mode
Work Mode
Sleep Mode
Soldering Iron Tip Warning
High Voltage Warning
High Temperature
Warning
Low Voltage Warning
PCB High
Temperature Warning
Power Supply Voltage
Soldering Iron Tip Temperature
Soldering Iron Tip Warning
High Voltage Warning
High Temperature
Warning
Low Voltage Warning
PCB High
Temperature Warning
Working Temperature Setpoint
Power Progress Bar
Short press the rotary switch to switch between "Stop"
mode and "Work" mode
Please re-adjust the position of the soldering iron tip or
replace the soldering iron tip. After the warning condition is
cleared, the warning icon will automatically change to Stop.
Please use DC12-25V/3S-6S power supply. After the warning
condition is eliminated, the warning icon will automatically
change to Stop.
Please disconnect the power supply, cool down the
soldering iron tip to room temperature, and then reconnect.
After the warning condition is removed, the warning icon
changes to Stop by pressing or turning the rotary switch.
Please increase the supply voltage or decrease the LowVolt
setting value. After the warning condition is removed,short
press or turn the rotary switch and the warning icon
changes to Stop.
Please disconnect the power supply, cool down the
soldering station to room temperature, and then reconnect.
After the warning condition is removed, the warning icon
changes to Stop by pressing or turning the rotary switch.
Please re-adjust the position of the soldering iron tip or
replace the soldering iron tip.
Please use DC12-25V/3S-6S power supply
Please disconnect the power supply, cool down the
soldering iron tip to room temperature, and then reconnect.
Please increase the supply voltage or decrease the LowVolt
setting value.
Please disconnect the power supply, cool down the
soldering station to room temperature, and then reconnect.
Rotate the rotary switch to set the working temperature
value.
1
2
3
4
5
/
/
/
/
（1）Main Interface
Level 1
Menu Level 2 Menu Description Default
Value Setting Range
Iron
Idle
Lcd
Volt
Calib
About
1.Tcomp
2.Buzzer
3.TempUnit
4.WorkTemp
5.StartHeat
6.FactorySet
7.TempShield
8.TempStep
9.Logo
1.SleepTime
2.SleepTemp
3.IdleTime
4.Sensitive
5.ScreenOpen
1.Brightess
2.Direction
3.KeyAction
4.ColorState
5.ColorSetT
6.ColorNowT
7.ColorVolt
8.ColorPower
1.LowVolt
2.PowerVolt
/
/
Temperature compensation
Buzzer
Temperature unit
Working temperature
Automatic heating when power on
Factory reset
Temperature display is stable
Working temperature setting
step value of main interface
Customize the boot logo
Sleep time
Sleep temperature
Standby time
Wake Sensitivity
Standby screen display
Display brightness
Display direction
Rotation direction
Working status font color
Working temperature set point font color
Soldering iron tip temperature font color
Supply voltage font color
Power progress bar color
Low voltage protection
Supply voltage compensation
Temperature calibration
Information about Soldering Station
0V
/
/
/
/
/
/
/
10.0V
L-R+
0°
50
ON
5
360s
200℃
180s
OFF
10
ON
OFF
OFF
300℃
℃
ON
0℃ -20℃-20℃
OFF/ON
℃/℉
100℃-450℃
OFF/ON
OFF/ON
OFF/ON
10-50
OFF/ON
60-990s
100℃-450℃
60-990s
1-30
OFF/ON
5-100
0°/180°
L-R+/L+R-
10 colors
10 colors
10 colors
10 colors
10 colors
OFF/10.0-23.0V
-5.00-5.00V
T1-T4
/
（2）Level 1 Menu 、Level 2 Menu
(3) Menu Operation Guidelines
Main interface：
① Short press the rotary switch to switch between "Stop"
mode and "Work" mode.
② Turn the rotary switch to adjust the working temperature
setting value.
③ Long press the rotary switch to enter the level 1 menu.
④ A warning icon appears. After the warning condition is
eliminated, short press or turn the rotary switch to turn
the warning icon to Stop.
Secondary menu：
① Turn the rotary switch to cycle through the level 2 menu
function box.
② Short press the rotary switch to confirm entering the level
2 menu setting item, and the parameter setting box will
appear. Turn the rotary switch to set this parameter. After
the parameter setting is completed, long press the rotary
switch or no key operation for 8s, it will automatically exit
the parameter setting box and return to the level 2 menu.
③ After long pressing the rotary switch or no key operation
for 8s, it will return to the level 1 menu menu.
Level 1 menu：
① Turn the rotary switch to cycle through the level 1 menu function box.
② Short press the rotary switch to enter the level 2 menu.
③ After long pressing the rotary switch or no key
operation for 8s, return to the main interface.
(4) Temperature Calibration
Calib
Fix
Real
T1
Save
Fixed Value
Real Value
Thermometer
Temperature
Save
Temperature calibration is divided into four parameters T1,T2,T3,T4, after
entering the calibration interface, T1 temperature parameter is selecting
box by default ,short press the rotary switch,T1 temperature parameter
changes to setting box , waiting for value of “Real” to steadily
fluctuate within value range of "Fix".Thermometer to measure real temperature of
soldering iron tip,turn rotary switch to write thermometer data to T1, after setting
T1 calibration temperature, long press rotary switch to exit the setting box, turn
rotary switch to select T2, continue to complete temperature calibration of T2,
T3, T4.Finally enter “Save”, short press rotary switch until “Save Succeed”
appear, calibration is complete.
During calibration process, long press rotary switch to exit calibration
interface, parameters are not saved.
In process of temperature calibration, add tin to clean soldering
iron tip first, then use thermometer to measure temperature,during
calibration,soldering iron tip is in a high temperature state,avoid scalding.
3.Eliminate Warning
When the soldering iron occurs a warning , a warning icon is displayed on the screen (if the buzzer is
open, will accompany the warning beep), according to the prompt warning icon,troubleshot step
by step after the warning condition is eliminated (if the buzzer is open, the warning beep will stop
immediately), short press or turn rotary switch,warning icon (main interface 1) change to Stop.
4.Sleep Wake Up
Work mode, the soldering station will enter sleep mode automatically after waiting for SleepTime
seconds when the handle is in a static state, the temperature will be automatically set to SleepTemp.
Sleep mode, wake up the soldering station and automatically restore the original setting of
WorkTemp when short press or turn rotary switch or shake the handle; If the soldering station is not
woken up, after waiting for IdleTime the soldering station stop working,enter Stop mode.
Stop mode, the handle is in a static state and rotary switch without operation,after waiting for 180s
enter ScreenOpen,can exist by short press or turn rotary switch or vibrate the handle.
5.Technical Reference
Input
Voltage Power Fastest Time from
30℃ to 300℃
12V
19V
24V
16W
40W
70W
37S
14S
9S
AC100-
240V 70W 9S
6.Firmware Update
Visit www.sequremall.com to obtain
firmware and upgrade teps.
Attention:MSS12 Pro before the firmware
upgrade, ensure that the XT60 and AC port
is disconnected,USB-C can be connected
to a computer to avoid damage.
7.Custom Boot LOGO
Connect USB-C with a computer, enter the level 1 menu "Iron" to select "9.Logo",
set it to "ON",long press rotary switch or wait for automatic saving,enter to the
LOGO interface,at this time the computer will appear a disk named "LOGO".Copy
the image named “LOGO.bmp” to the disk and disconnect.
Note:The picture is in unit color. bmp format,128 * 100 pixels,level is 128,vertical is 100,
named “LOGO.bmp”
8.Warranty Terms
1 . Performance failure caused by non-human factors occurs within 3 months from the date
of purchase,the manufacturer provides free repair service.After 3 months, no labor fee
will be charged for the repair,if the parts are replaced, the cost shall be borne by the user.
2 . All artificial damage, self-disassembly,failure caused by improper use, and consumable
soldering iron tip, is not covered by this warranty.
9.Safety Precautions
Use power supplies and accessories that meet safety standards,use original SEQURE
accessories.
Must make sure that the power is off, can replace the soldering iron tip, to avoid
damaging the product,beware of high temperature burns.
Soldering iron tip burn easily,power off after rest or completion,store in place not easily
accessible to children.
Under any circumstances, only choose XT60, AC or USB-C to supply power for the
MSS12 Pro soldering station,can not be connected at the same time, to avoid damage.
www.sequremall.com
-
1
SEQURE MSS12 Pro is a smart soldering station with a 1.14" LCD color screen that supports multiple power supply methods including PD2.0/3.0, QC2.0/3.0, DC12V-25V, and XT60 3S-6S, as well as AC100-240V. It features firmware upgrade capability, custom boot logo, changeable main interface color, and the ability to switch between Celsius and Fahrenheit. With intelligent temperature control, it can achieve a precision of plus or minus 1%.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
HOZAN HS-51 Owner's manual
-
ersa i-CON 1V Operating Instructions Manual
-
QRP Labs QCX 5W CW Assembly Instructions Manual
-
Sharp XEA102 - Cash Register User manual
-
Quick 3202 Operating instructions
-
Aktakom ASE-4313 User manual
-
-
Elenco M2666K Owner's manual
-
Epson Photo PC-750Z User manual
-
