2. Leviton
  3. 78W47-C

Leviton 78W47-C Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Leviton 78W47-C Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Wetguard
®
Connectors
(For use with Wetguard
®
Inlets only)
NEMA & NON-NEMA
IP66 Suitability. Rated to NEMA Type 4, 4X & 12
when mated with Leviton Wetguard
®
Inlets
PK-93740-10-00-0A
WARNINGS AND CAUTIONS:
• Tobeinstalledand/orusedinaccordancewithappropriateelectricalcodesandregulations.
• Ifyouarenotsureaboutanypartoftheseinstructions,consultanelectrician.
• Usethisdevicewithstranded copper wire only.
• Non-grounded devices are for connection to non-grounded circuits only.
• Non-NEMAdevicesareULListedforreplacementuseonly.
WIRING INSTRUCTIONS
ENGLISH
TO INSTALL
NOTE:WIRESIZEANDTYPEMUSTCOMPLYWITHAPPROPRIATELOCALELECTRICALCODES.INUSAREFERTONECTABLESARTICLE400.
WARNING:TOAVOIDFIRE,SHOCKORDEATH;UNPLUG CORD OR TURN OFF POWER
ATCIRCUITBREAKERORFUSEANDTESTTHATPOWERISOFFBEFOREWIRING!
1.Selectsizeandtypeofroundcordasperyourrequirements.
2.ReferringtoFig. 1,removenut(1)fromrubberhousing(3).Separatewiringmodule(4)from
rubberhousingbypushingthemodulefrombackofhousingwithascrewdriver(orcord).
3.Selectpropersizeofstrainreliefwasher(10)andrubberbushing(9)peryourcordsizeasper
appropriate table below,orusethebackoftherubberbushingasagage.The washers and
bushings must be broken apart from each other before use (see Fig. 1).
4.Feedwiringcordthroughnut(1),strainreliefwasher(10),rubberbushing(9)andintothreaded
insertofhousing(3)asshowninFig. 1. DO NOT REVERSE ORIENTATION OF STRAIN
RELIEF WASHER AND RUBBER BUSHING.
5.Stripcordjacketandconductorsasperappropriatewire stripping gage, or as per strip gage
moldedonthebackofwiringcover.
6. Connect wires:Carefullybackoutallterminalwiringscrewsuntiledgeofbackwireclampis
notvisibleinwirewell.Twistthestrandsofeachstrippedconductortightlytogether,andinsert
intoproperwirewell.Tightenwiringscrewrmlyto12-14in.-Ibs.Torque.CHECK FOR STRAY
WIRE STRANDS. Repeat for all conductors. NOTE:Whereapplicableitisrecommendedto
connectGROUNDwirerst.
CAUTION: Wiring clamps MUST contact on conductor only, NOT on insulation.
DO NOT USE SOLID WIRE. DO NOT TIN CONDUCTORS.
7.Reattachthewiredmodule(4)tothehousing(3)byaligningkeyguide(8)onthemoduletothe
keyonthehousing,andtightentheassemblyscrewsrmlyto10-14in.-Ibs.torque.
8.Pushuprubberbushing(9)andstrainreliefwasher(10)overcordsothatthenutcanengage
the threaded insert.
IMPORTANT:Rubberhousingmustbeheldrmlywhentighteningnut.
NOTE 1: Usebackofrubberbushingsasagageforcablesizeorappropriate table below.
Alwaysusematchedbushingandstrainreliefwashers.
NOTE 2:
Polarity of wiring for NEMA devicesisidentiedbymarkingsondeviceand/orscrew
colorasshownbelow.ForPolarityofwiringforNON-NEMAdevicesrefertodevice(s)tobe
replacedforspecicwiringpattern.
1
2
3
4
A
B
C
D
5
6
7
9
10
8
Fig. 1 - Locking Connector (3 wire shown)
1 - Nut
2 - Cord
3 - Rubber Housing
4 - Wiring Module
5 - Threaded Insert
6 - Assembly Screws
7 - Terminal Screws
8 - Key Guide on Wiring Module
(to be aligned with Key on Housing)
9 - Rubber Bushing (select as per Strain Relief Washer)
10 - Strain Relief Washer
MARKING ON NEMA DEVICE
G, GRND, GREEN, or EQ GR
W, or WHITE
X,Y,Z or BLANK
CONDUCTOR COLOR
Bare, Green, or Green/Yellow wire
White or Gray wire
Black, Red, Blue or any other than White, Green, Gray, Green/Yellow or Bare wire
NEMA SCREW COLOR
(Grounding) -- GREEN
(Neutral) -- SILVER
(Hot) -- BRASS or BLACK
Wire Stripping Gage – 20A & 30A (3-5 wire) LockingWire Stripping Gage – 15A & 20A (2-3 wire) Straight Blade,
15A (2-3 wire) Locking, 20A (2 wire) Locking
Insulation
5/8"(1.6 cm)
All Conductors
1"(2.5 cm)
All Conductors except 5 wire Ground
Cord Jacket
5 Wire Ground Only
1-1/2"(3.8 cm)
15/16"
(2.38 cm)
9/16"
(1.43 cm)
Cord Jacket
Insulation
©2011LevitonMfg.Co.,Inc.
15A & 20A (2-3 wire) Straight Blade, 15A (2-3 wire) Locking, 20A (2 wire) Locking
20A (3 - 5 wire) Locking
18/3 S, ST, SO, SOW
16/3 S, ST, SO, SOW
14/3 SJ, SJT, SJTO, SJTOW
14/2 SJ
16/4 SO, SOO, ST, STO, SJ, SJO, SJT
14/3 SO, SOO, ST, STO, SJ, SJO, SJT
12/4 SO, SOO, ST, STO, SJ, SJO, SJT
14/4 SO, SOO, ST, STO, SJ, SJO, SJT
12/3 SO, SOO, ST, STO, SJ, SJO, SJT
12/3 SO, SOW
12/4 SO, SOO, ST, STO
10/2 SO, SOW
12/5 SO, SOO, ST, STO
10/3 SOW
10/3 SO, SOO, ST, STO
14/3 S, ST, SO, SOW
10/5 SO, SOO, ST, STO
12/3 SO, SOO, ST, STO
14/4 SO, SOO, ST, STO
Bushing/Washer Gage (AWG) Type Range
A 18/2 S, ST, SVT, SO, SOW .234 - .437
A
16/3 SO, SOO, ST, STO, SJ, SJO, SJT .375-.500
C 12/2 SO, SOW .562-.687
C 14/5 SO, SOO, ST, STO .625-.750
B 14/2 S, ST, SO, SOW .437-.562
D 10/4 SO, SOO, ST, STO .750-.875
B 14/3 SO, SOO, ST, STO .500-.625
BUSHING AND STRAIN RELIEF CORD SIZING
30A (3 - 5 wire) Locking
12/4 SJ, SJO, SJT, SO, SOO, ST, STO
12/5 SJ, SJO, SJT, SO, SOO, ST, STO
10/3 SJ, SJO, SJT, SO, SOO, ST, STO
10/4 SJ, SJO, SJT, SO, SOO, ST, STO
8/3 SO, SOO, ST, STO
10/5 SO, SOO, ST, STO
Bushing/Washer Gage (AWG) Type Range
A 12/3 SJ, SJO, SJT, SO, SOO, ST, STO .625-.750
C 8/4 SO, SOO, ST, STO .875-1.000
D 8/5 SO, SOO, ST, STO 1.000-1.125
B 10/4 SO, SOO, ST, STO .750-.875
BUSHING AND STRAIN RELIEF CORD SIZING
For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only) www.leviton.com
LIMITED LIFETIME WARRANTY AND EXCLUSIONS
Levitonwarrantstotheoriginalconsumerpurchaserand notforthebenet ofanyoneelsethat thisproductat thetime ofitssale byLevitonisfreeof defectsinmaterials andworkmanshipundernormal
and proper use during the lifetime of the product.Leviton’s only obligation is to correct such defects byrepair or replacement, at its option, if the product is returnedprepaid, with proof of purchase
date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melville, N.Y. 11747.This warranty excludesand there
is disclaimed liability forlabor forremoval of this product or reinstallation.This warranty is void if this product is installed improperly or in an improper environment,overloaded, misused, opened,
abused, or altered in any manner, or is not used under normaloperating conditions or not in accordance with any labels or instructions. There are no other or implied warrantiesof any kind, including
merchantabilityandtness foraparticular purpose.Levitonisnot liableforincidental,indirect,special,or consequentialdamages,includingwithoutlimitation, damageto,orlossof useof,anyequipment,
lost sales or prots or delay or failureto perform this warrantyobligation.The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tortor otherwise.
PK-93740-10-00-0A
TheseproductsarecoveredbyPatents:US5,863,221;US6,017,243;CA2,243,838;
CA2,266,253;MX225,136andMX215,544.
/