• Remove and clean the screen washer on inlet side of the timer
every few months.
• In freezing conditions, uninstall the timer and bring it indoors to
prevent damage.
Maintenance
I N S T R U C T I O N M A N U A L
1210 Activity Drive
Vista, CA 92081-8510, USA
800-344-2281 • 760-727-0914
e-mail: [email protected]om
26-233 REV A
Attach the timer inlet to
the outdoor faucet/spigot
turning clockwise – hand
tighten only. From the
timer outlet connect a
drip irrigation system or
a garden hose.
How to install
3/4 in. female
hose thread
with screen
washer
3/4 in. male
hose thread
setting – tiMe & Date
a
Push
to select the hour and adjust using .
AM/PM is set by increasing or decreasing the hour.
Push
to confirm your settings.
setting – start tiMes
c
Push to select Start Time . By default Start Time 1 is set to 6:00 AM.
Push
to select the hour and adjust using then push to set
minutes. To set additional start times push
. Up to 4 start times can be
programmed. Push
to confirm your settings.
View all set start times by pressing
.
Push
to select Set Days . By default all days are set to water.
Push
and advance through days of the week using . Deselect
or select a day to water using
.
Push
to confirm your settings.
Push
to select Set Days . Push and hold for three
seconds. Default settings will be restored but current time and date
will be retained.
Push
to select Set Days .
Push
and then push until the days of the week can be seen at
the top of the LCD screen. Push
and advance through days of the
week using
and select each day to water using . Push to
confirm your settings.
Push
to select the hour then push to advance or decrease the
hours until the display shows OFF. Push
to confirm your settings.
Push
to select Set Days .
Push
and advance through days of the week using until 1 DAY
appears flashing. Push
to select to water once every 1 to 30 days.
Push
to confirm your settings.
setting – watering Days
B
Push
to select Set Days .
Push
and advance through days of the week using until EVEN
appears flashing. Push
to select ODD. Push to confirm your
settings.
setting – run tiMes
D
Push to select Run Time . By default the Run Time is set to 5 min.
Push
to select the hour and adjust using then push to set
minutes. Push
to confirm your settings.
setting – rain Delay
e
Used to shut down timer in winter or when it is raining. Set schedules will
be retained and programmed watering will resume after the delay time
is completed.
Push
to select Rain Delay . Push then adjust to the number of
days to suspend watering using
. Push to confirm your settings.
To cancel the Rain Delay, set the days to OFF using
.
Manual run
F
To instantly water push .
Push
to stop or the timer will run for the programmed time (if set).
Default watering time is 5 min.
The purpose of using a sensor is to prevent automatic watering by the set
program due to excessive rainfall. Most “normally closed” rain sensors can be
used with the EVO 100 timer.
1. Cut the yellow wire loop in the center and splice to each of the
sensor wires using .
2. Follow the sensor manufacturer’s instructions for calibrating the sensor.
3. When the sensor is active and preventing watering, the
icon will appear.
using a sensor
SET DAYS
START TIME
CURRENT POWER LEVEL
CURRENT TIME DATE
RUN TIME
RAIN DELAY
CURRENTLY WATERING
SENSOR ACTIVE
MANUAL RUN
-
1
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Holman EVO1001 User manual
-
Hunter X-CORE Owners Manual And Programming Instructions
-
Hunter Pro-C Owner's Manual and Installation Instructions
-
-
-
Orbit 57950 User guide
-
Orbit 57946 User manual
-
Orbit 94922 User manual
-
-
