Target Britanna GCS09062H Assembly Instructions

Brand: Target

Model: Britanna GCS09062H

Type: Assembly Instructions

This manual is also suitable for

Britanna Hanging Egg Chair

hanging egg chair

style # GCS09062H

dpci # 009000186

>>assembly instructions TM

Britanna

Congratulations on your latest Target purchase.

Now what? Don't start sweating over this box of parts. This will be easy. We did the hard work for you.

All you need to do is follow our simple instructions and you'll be on your way to transforming your patio in no time.

Good luck – though we're confident you won't need it.

ATTENTION:

This Chair is not intended for use during any kind of inclement weather and the manufacturer is not

and can not beheld responsible for any damages caused as a result of such weather. Weather-related

damage, or damage as a result of the Chair not being stored properly when not in use is not the

responsibility of the manufacturer.

During extended periods of non-usage, off season, or in inclement weather (wind, rain, snow, hail,

sleet), freezing conditions and extreme heat, the Chair needs to be stored in a dry sheltered place to

prolong the life and to avoid damage to the Chair.

IMPORTANT WARNING:

Unpack the box on a clean soft level surface and make sure all parts have been included.

To replace missing or damaged parts please call 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.

WEIGHT LIMIT 250 LBS MAXIMUM.

Chair is intended to be used by one person at a time.

Chair and stand must be used with all provided parts. Ensure that all parts are

installed according to instructions and inspected for damage before use.

Ensure that all bolts and hardware are securely tightened and installed before use.

Always inspect your chair, hardware, and stand for damage before use.

Never place infants or pets in the chair.

Never allow young children to use chair without adult supervision.

Do not jump, stand, or twist in chair.

Chair and stand are designed for minimal swing motion. Use care when getting in and

out of chair. If using stand, ensure that chair is facing forward and do not cause chair

to swing outside base area of stand.

Stand must be used with attached safety rope, included with product.

Do not climb on support pole.

Use on even-flat surfaces only.

This hanging egg chair is not a toy.

WARNING-TO AVOID RISK OF FALLING

WARRANTY:

This Chair comes with a one year limited warranty against original manufacture defects. If you experience

trouble with your chair, please call the customer service number below.

Target Corporation

Toll Free at: 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.

Code: Yotrio 2020

before you begin

1. Check for damage or missing parts. Call to order missing supplies.

2. Use the carton as a working surface to prevent product damage during assembly.

3. Gather all tools prior to assembly.

855-MYTGTHOME (855-698-4846)

table of contents

introduction

hardware

parts list

assembly

2-3

7-13

QUESTIONS?

4Please call 855-MYTGTHOME (855-698-4846) parts and service. For faster service, have th e style number and DPCI number ready when calling.

hardware

(Part H)×2

M8*15mm bolt

(Part V)×1

wrench

(Part U)×1

allen wrench

(Part I)×7

M8*20mm bolt with washer

(Part J)×4

M6*45mm bolt with washer

(Part G)×2

M8*55mm bolt

(Part L)×4

M6 washer

(Part K)×2

M6*15mm bolt with washer

(Part M)×4

M6 nut

(Part N)×9

M8 washer

(Part R)×2

plastic muffler

(Part O)×2

M8 spring washer

(Part P)×9

M8 nut

(Part Q)×1

hook

(Part S)×2

post plastic part

(Part T)×1

connection part

ITEM DESCRIPTION QUANTITY

left base

B right base 1

Clower hanging bar

Dupper hanging bar

Eback frame

Fseat frame

Qhook

Rplastic mulffer 2

Spost plastic part 2

Tconnection part 1

step 01:

ATTENTION: To avoid damage to your new patio furniture, please

use either the carton or another soft surface such as carpet as a

working surface to prevent product damage during assembly.

1. Connect left base (A) and right base (B) by using post plastic part (S) and connection part (T).

Secure with M6*15mm bolt with washer (K) using allen wrench (U).

2. Lining up the bolt holes on the end of the left base (A) with the corresponding bolt

holes on the right base (B).

(Part K)×2

M6*15mm bolt with washer

(Part N)×3

M8 washer

(Part I)×3

M8*20mm bolt with washer

(Part P)×3

M8 nut

(Part T)×1

connection part

(Part U)×1

allen wrench

1. 2.

(Part V)×1

wrench

Do not completely tighten screws until all screws are in place.

3. Secure with M8*20mm bolt with washer (I), M8 washer (N) and M8 nut (P) using

allen wrench (U) and wrench (V).

(Part S)×1

post plastic part

step 02:

1. Attach the lower hanging bar (C) to the left base (A) and right base (B) by lining up

the bolt holes on the lower hanging bar (C) with the corresponding bolt holes on the

left base (A) and right base (B).

2. Secure with M8*20mm bolt with washer (I), M8 washer (N) and M8 nut (P) using allen

wrench (U) and wrench (V).

(Part I)×4

M8*20mm bolt with washer

(Part N)×6

M8 washer

(Part H)×2

M8*15mm bolt

(Part O)×2

M8 spring washer

(Part U)×1

allen wrench

(Part V)×1

wrench

Do not completely tighten screws until all screws are in place.

3. Secure with M8*15mm bolt (H), M8 spring washer (O) and M8 washer (N) using allen

wrench (U).

(Part P)×4

M8 nut

step 03:

1. Connect upper hanging bar (D) and lower hanging bar (C) by using post plastic part (S).

Secure with M8*55mm bolt (G), M8 washer (N) and M8 nut (P) using allen wrench (U)

and wrench (V).

2. Attach the plastic muffler (R) to the hook of upper hanging bar (D).

(Part N)×2

M8 washer

(Part P)×2

M8 nut

(Part G)×2

M8*55mm bolt

(Part U)×1

allen wrench

1. 2.

(Part V)×1

wrench

Do not completely tighten screws until all screws are in place.

(Part S)×1

post plastic part

(Part R)×1

plastic muffler

step 04:

1. Attach the back frame (E) to the seat frame (F) by lining up the bolt holes on the

back frame (E) with the corresponding bolt holes on the seat frame (F).

2. Secure with M6*45mm bolt with washer (J), M6 washer (L) and M6 nut (M) using

allen wrench (U) and wrench (V).

(Part L)×4

M6 washer

(Part M)×4

M6 nut

(Part J)×4

M6*45mm bolt with washer

(Part R)×1

plastic muffler

(Part U)×1

allen wrench

(Part V)×1

wrench

Do not completely tighten screws until all screws are in place.

3. Attach the plastic muffler (R) to the hook of back frame (E).

1. 2. 3.

step 05:

1. Follow the diagram in circle 1 to open the hook (Q). Connect the upper hanging bar (D)

and back frame (E) by using the hook (Q). Then tighten the hook (Q).

(Part Q)×1

hook

1. 2.

Do not completely tighten screws until all screws are in place.

step 06:

1. Open the hook of safety rope on the seat frame (F), pass through the bottom of

the lower hanging bar (C). Then tighten the hook of safety rope.

Do not completely tighten screws until all screws are in place.

1. 2. 3.

step 07

1. Tighten all the bolts.

2. Put the cushion on the chair.

You are now ready to enjoy your new chair.

Target Britanna GCS09062H Assembly Instructions

Brand: Target

Model: Britanna GCS09062H

Type: Assembly Instructions

This manual is also suitable for

Britanna Hanging Egg Chair

Download PDF

report

Target Britanna GCS09062H Assembly Instructions

This manual is also suitable for

Target Britanna GCS09062H Assembly Instructions

Related papers

Other documents