Latigo
Egg Chair
style # FRS50006H-1
dpci # 009000798
>>assembly instructions TM
Congratulations on your latest Target purchase.
Now what? Don't start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you'll be on your way to transforming your patio in no time.
Good luck – though we're confident you won't need it.
ATTENTION:
This Chair is not intended for use during any kind of inclement weather and the manufacturer is not,
and can not beheld responsible for any damages caused as a result of such weather. Weather-related
damage, or damage as a result of the Chair not being stored properly when not in use, is not the
responsibility of the manufacturer.
During extended periods of non-usage, off season, or in inclement weather (wind, rain, snow, hail,
sleet), freezing conditions and extreme heat, the Chair needs to be stored in a dry, sheltered place to
prolong the life and to avoid damage to the Chair.
2
IMPORTANT WARNING:
Unpack the box on a clean, soft, level surface and make sure all parts have been included.
To replace missing or damaged parts please call 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.
WARRANTY:
This Chair comes with a one year limited warranty against original manufacture defects. If you experience
trouble with your chair, please call the customer service number below.
3
Target Corporation
Toll Free at: 855-MYTGTHOME (855-698-4846) during 7am - 7pm CST M-F, and 8am - 5pm CST Saturday.
Code: Yotrio 2019
before you begin
1. Check for damage or missing parts. Call to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
855-MYTGTHOME (855-698-4846)
table of contents
introduction
hardware
parts list
assembly
2-3
5
6
7-10
QUESTIONS? Please call 855-MYTGTHOME (855-698-4846) parts and service. For faster service, have th e style number and DPCI number ready when calling.
hardware
5
(Part I)×2
Connecting
(Part D)×7
M6 nut
(Part G)×3
M6*45 bolt with washer
(Part E)×4
spring washer
(Part F)×7
washer
(Part H)×4
M6*30 flat bolt with washer
(Part J)×2
hex wrench
(Part K)×1
allen wrench
6
ITEM DESCRIPTION QUANTITY
1
A
6
back frame
B seat frame 1
1
Cleg frame
7
step 01:
ATTENTION: To avoid damage to your new patio furniture, please
use either the carton or another soft surface such as carpet as a
working surface to prevent product damage during assembly.
2. Attach the leg frame (C) to the seat frame (B) by lining up screw holes
on the seat frame (B) with corresponding screw holes on the leg frame (C).
3. Secure with M6*30 flat bolt with washer (H) washer (F), spring washer (E)
and M6 nut (D). tighten using allen wrench (K) and hex wrench(J) .
1. Place the seat frame (B) upside down on a soft surface such as carpet.
(Part D)×7
M6 nut
(Part G)×3
M6*45 bolt with washer
(Part E)×4
spring washer
(Part F)×7
washer
(Part H)×4
M6*30 flat bolt with washer
(PartJ)×2
hex wrench
(Part K)×1
allen wrench
(Part I)×2
Connecting
8
C
A
B
I
8
step 02:
ATTENTION: To avoid damage to your new patio furniture, please
use either the carton or another soft surface such as carpet as a
working surface to prevent product damage during assembly.
2. Attach the back frame (A) to the seat frame (B) and leg frame (C) by lining up screw holes
on the seat frame (B) with corresponding screw holes on the back frame (A).
1. Place the leg frame (C) and seat frame (B) right side up on a soft surface such as carpet.
3. Insert the connecting (I) into the upper and lower tube.
(Part D)×7
M6 nut
(Part G)×3
M6*45 bolt with washer
(Part E)×4
spring washer
(Part F)×7
washer
(Part H)×4
M6*30 flat bolt with washer
(PartJ)×2
hex wrench
(Part K)×1
allen wrench
(Part I)×2
Connecting
9
step 03:
ATTENTION: To avoid damage to your new patio furniture, please
use either the carton or another soft surface such as carpet as a
working surface to prevent product damage during assembly.
1. Attach the back frame (A) to the seat frame (B) and leg frame (C) by lining up screw holes
on the seat frame (B) with corresponding screw holes on the back frame (A).
3. Secure with M6*45 bolt with washer(G),washer (F) and M6 nut (D). tighten using allen
wrench (K) and hex wreanch (J).
A
B
C
G
D
F
(Part D)×7
M6 nut
(Part G)×3
M6*45 bolt with washer
(Part E)×4
spring washer
(Part F)×7
washer
(Part H)×4
M6*30 flat bolt with washer
(PartJ)×2
hex wrench
(Part K)×1
allen wrench
(Part I)×2
Connecting
10
step 04
1. T
ighten all the screws.
2. Turn the chair to upright position on a flat level surface.
Put the cushion on the chair.
You are now ready to enjoy your new chair.
TM
2019 Target. The Bullseye Design is a trademark of Target Brands Inc. All rights reserved.
/
