aFe Power Mach Force XP 2.5" 409 Stainless Steel Cat Back Exhaust System Installation guide

Type
Installation guide

aFe Power Mach Force XP 2.5" 409 Stainless Steel Cat Back Exhaust System is designed to provide increased horsepower and torque, improved throttle response, and a more aggressive exhaust note. Constructed from durable 409 stainless steel, this exhaust system is corrosion-resistant and built to last. The 2.5" diameter tubing provides increased exhaust flow, while the mandrel-bent design ensures a smooth and efficient flow path. This exhaust system is compatible with Jeep Wranglers (JL) manufactured from 2018 onwards and equipped with the V6-3.6L engine.

aFe Power Mach Force XP 2.5" 409 Stainless Steel Cat Back Exhaust System is designed to provide increased horsepower and torque, improved throttle response, and a more aggressive exhaust note. Constructed from durable 409 stainless steel, this exhaust system is corrosion-resistant and built to last. The 2.5" diameter tubing provides increased exhaust flow, while the mandrel-bent design ensures a smooth and efficient flow path. This exhaust system is compatible with Jeep Wranglers (JL) manufactured from 2018 onwards and equipped with the V6-3.6L engine.

INSTALLATION INSTRUCTIONS
MAKE: Jeep
MODEL: Wrangler (JL)
YEAR: 2018
ENGINE: V6-3.6L (4DR)
409 Stainless Steel
2-1/2" Cat-Back Exhaust
49-48065-P (Polished)
49-48065-B (Black)
48-48065 (Hi-Tuck)
Step 1: (Read Instructions prior to installation). It may be helpful to lubricate all the factory isolation rubber mounts, before taking off stock
exhaust and also before installing aFe exhaust. Always use a jack or stand for support when installing or uninstalling any exhaust
system.
Step 2: Begin by removing your stock exhaust from the rear of your truck working your way forward. Remove the factory muffler assembly
and mid-pipe/resonator. Take caution not to damage the factory isolation mounts as they will be reused
NOTE: It may be easier to unbolt the muffler hanger brackets from the frame than to disconnect the factory isolation mounts.
Step 3: Remove the factory ball clamp from the mid-pipe/resonator.
Step 4: For faster installation spread the pieces of the exhaust alongside of your vehicle, according to the diagram shown. It is
recommended to not fully tighten any of the clamps until the entire system has been fully installed.
Step 5: Place the factory ball clamp removed in Step 3 onto the muffler assembly.
Step 6: Install the muffler assembly onto the factory y-pipe and loosely tighten the factory ball clamp.
Step 7: Place a 2.5" band clamp over the rear side of muffler assembly. Slide the mid-pipe into muffler and slip the hanger into rubber
isolation mounts.
NOTE: If the factory muffler hanger brackets were removed from the frame at Step 2 then reinstall the drivers-side hanger
bracket and isolator before Step 8.
Step 8: Place a 2.5" band clamp over the rear side of the mid-pipe. Slide the tail pipe into the mid-pipe and slip the hanger into the
rubber isolation mount.
Step 9: For 49-48065-B and 49-48065-P, install the exhaust tip onto the tail pipe.
Step 10: Straighten all exhaust components and begin to tighten down all clamps beginning at the front and ending at the rear.
Step 11: Congratulations your exhaust is now complete.
NOTES:
• aFe recommends that the tailpipe be at least 1/2"-1” away from any body panels to avoid heat related body damage. Tighten and secure.
06-86385
Updated: Febuary, 2018
Caution: Allow time for your vehicle to cool down prior to installation. When working on or under your vehicle proceed with caution. Exhaust systems reach high
temperatures and may cause serious burns. Wear protective safety equipment; eye goggles and gloves to ensure a safe installation. aFe recommends professional
installation on our products.
Clamp, Band 2-1/2"
05-41061
Muffler Assembly
05-144392 Mid-Pipe
05-144393
Tail-Pipe
05-144394
Clamp, Band 2-1/2"
05-41061
Exhaust Tip
49T25354-P06 (Polished)
49T25354-B06 (Black)
Clamp, Band 2-1/2"
05-41061
  • Page 1 1

aFe Power Mach Force XP 2.5" 409 Stainless Steel Cat Back Exhaust System Installation guide

Type
Installation guide

aFe Power Mach Force XP 2.5" 409 Stainless Steel Cat Back Exhaust System is designed to provide increased horsepower and torque, improved throttle response, and a more aggressive exhaust note. Constructed from durable 409 stainless steel, this exhaust system is corrosion-resistant and built to last. The 2.5" diameter tubing provides increased exhaust flow, while the mandrel-bent design ensures a smooth and efficient flow path. This exhaust system is compatible with Jeep Wranglers (JL) manufactured from 2018 onwards and equipped with the V6-3.6L engine.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI