NEC N8800-096F User manual

Brand: NEC

Model: N8800-096F

Category: Soundbar speakers

Type: User manual

This manual is also suitable for

NEC Express5800 Series

N8800-096F, EXP320B

NEC Express5800/320Fb-L

N8800-097F, EXP320A

NEC Express5800/320Fb-LR

N8800-098F, EXP320D

NEC Express5800/320Fb-M

N8800-099F, EXP320C

NEC Express5800/320Fb-MR

User's Guide (Setup)

N8800-096F, EXP320B

NEC Express5800/320Fb-L

N8800-097F, EXP320A

NEC Express5800/320Fb-LR

N8800-098F, EXP320D

NEC Express5800/320Fb-M

N8800-099F, EXP320C

NEC Express5800/320Fb-MR

User's Guide (Setup)

1st Edition

12-2006

856-124126-411-00

PROPRIETARY NOTICE AND LIABILITY DISCLAIMER

The information disclosed in this document, including all designs and related materials, is the

valuable property of NEC Corporation (NEC) and /or its licensors. NEC and/or its licensors, as

appropriate, reserve all patent, copyright and other proprietary rights to this document, including all

design, manufacturing, reproduction, use, and sales rights thereto, except to the extent said rights are

expressly granted to others.

The NEC product(s) discussed in this document are warranted in accordance with the terms of the

Warranty Statement accompanying each product. However, actual performance of each such

product is dependent upon factors such as system configuration, customer data, and operator control.

Since implementation by customers of each product may vary, the suitability of specific product

configurations and applications must be determined by the customer and is not warranted by NEC.

To allow for design and specification improvements, the information in this document is subject to

change at any time, without notice. Reproduction of this document or portions thereof without prior

written approval of NEC is prohibited.

First Printing, December 2006

NEC Corporation

7-1 Shiba 5-Chome, Minato-Ku

Tokyo 108-8001, Japan

Printed in Japan

Keep this User's Guide handy for quick reference when necessary.

Safety Indications

To use NEC Express5800 series safely, follow the instructions in this User's Guide.

This guide explains components that pose a danger, types of dangers caused by failing to follow the

instructions, and actions taken to prevent them; such components are labeled warning.

This guide and warning labels use “WARNING” and “CAUTION” to indicate a danger depending on

the degree. These terms are defined as follows:

WARNING

Indicates a danger that could lead to a death or serious injury.

CAUTION

Indicates a danger that could lead to a burn, other injuries or damage to

physical assets.

This guide uses the following three types of symbols to give indications and precautions against a

danger. They are defined as follows:

Indicates that there is a risk of a danger. Each image symbolizes a particular type of

danger. (Attention)

Indicates what you must not do. Each image symbolizes a particular type of

prohibition. (Prohibited actions)

Indicates what you must do. Each image symbolizes a particular type of action

necessary to avoid a danger. (Mandatory actions)

(Example)

Symbol to draw attention

Term indicating a degree of danger

CAUTION

High temperature.

Immediately after the power-off, system components such as hard disk are

very hot. Wait the server to cool down completely before adding/removing

some component.

Symbol indicating a prohibited

action (may not always be

indicated)

Description of a danger

Symbols and its descriptions used in this User’s Guide and warning labels are as follows:

Attention

Indicates a risk of an electric shock.

Indicates a risk of a personal injury due to heat.

Indicates a risk of catching your fingers.

Indicates a risk of a fire or smoke.

Indicates a general precaution or warning that is not defined herein.

Indicates a risk of losing eyesight due to laser beam.

Indicates a risk of an explosion.

Indicates a risk of a personal injury.

Prohibited actions

Indicates a general prohibition that is not defined herein.

Do no touch the indicated area. There is a risk of an electric shock or fire.

Do not touch with wet hands. There is a risk of an electric shock.

Keep from flame. There is a risk of a fire.

Avoid using water or liquid nearby. If it spills on the equipment, there is a risk of an

electric shock or fire.

Do not disassemble, repair, or modify the equipment. There is a risk of an electric

shock or fire.

Mandatory actions

Unplug the server. There is a risk of an electric shock or fire.

Indicates a general action to take that is not defined herein. Make sure to follow the

instructions.

For detailed notes to set up the machine safely, refer to “NOTES FOR SAFE HANDLING” on page

1-2.

቟ోᵈᗧ੐㗄



ڜ٤ᑑق

ᓮ೶ەءش֪ਐতխऱਐقאڜ٤ࠌشNEC Express5800ߓ٨ۻࣚᕴΖ



ءش֪ਐতᎅࣔԱ๻ໂ۶๠ڶٲᙠΕٲᙠᣊীΕڕ۶ᝩ܍ٲᙠ࿛Ζڇ๻ໂױቃૠࠩऱٲᙠհ๠ࢨࠡॵ२

၀ڶᤞܫᑑ᧘Ζ



ش֪ਐত֗ᤞܫᑑ᧘խΔ௅ᖕٲᙠ࿓৫լٵΔࠌشϘᤞܫϙΕϘࣹრϙ࿛ဲΔܶᆠڕՀΚ



WARNING

।قڕլᙅښᇠਐقΔױ౨֧࿇Գ୉႞ՋΖ

CAUTION

।قڕլᙅښᇠਐقΔױ౨࿇سᗈ႞࿛ߪ᧯ჾ႞ࢨທګढᔆჾ؈Ζ



ኙٲᙠऱ༼ق।قڶڕՀԿጟฤᇆΔࠠ᧯ܶᆠڕՀࢬ૪Κ



।قᇠ๠ױ౨࿇سٲᙠΖฤᇆ੡ٲᙠփ୲ऱቹூΖΰࣹრα



।قᆃַ۩੡Ζฤᇆխࢨࠡॵ२ऱቹூ੡ᆃַ۩੡փ୲Ζΰᆃַ۩੡α



।قൎࠫ۩੡Ζฤᇆխऱቹூ੡ൎؘࠫႊ೚ऱ۩੡փ୲Ζܛ੡ᝩ܍ٲᙠؘᏁऱ۩੡Ζΰൎ

ࠫ۩੡α



ش֪ਐতխᒤࠏ

ࣹრฤᇆ



।قٲᙠ࿓৫ऱش፿



CAUTION



  



ࣹრ೏ᄵΖ



ءข঴ᣂຨሽᄭ৵Δփᆜ࿏጗࿛փຝ๻ໂսྥ๠࣍೏ᄵणኪΖᓮڇך։ܐথհ৵

ၞ۩ࣈᇘΖ

  





ᆃַ۩੡ऱ༼قฤᇆΰڶױ౨޲

ڶڼᣊ༼قα

ٲᙠ༼قփ୲



ء஼֗ᤞܫᑑ᧘խࠌشऱฤᇆ

ࣹრ



।قڶᤛሽऱٲᙠΖ



।قڶڂ೏ᄵۖ૤႞ऱٲᙠΖ



।قڶ֫ਐ࿛๯݈۰ऱٲᙠΖ



।قڶকᄿࢨृထ־ऱٲᙠΖ



।قॺ௽ࡳऱԫ౳ऱ༼ᙌᤞܫΖ



।قڶڂሼ୴ᖄી؈ࣔऱٲᙠΖ



।قڶᡨ੦ऱٲᙠΖ



।قڶ࠹႞ऱٲᙠΖ



ᆃַ۩੡



।قॺ௽ࡳऱԫ౳ᆃַΖ



լ૞ᤛ኷ਐࡳ೴഑Ζڶᤛሽࢨထ־ऱٲᙠΖ



լ૞شᛘ֫ᤛ኷ΖڶᤛሽऱٲᙠΖ



᎛ᠦ־ᄭΖڶထ־ऱٲᙠΖ



᎛ᠦ෈᧯Ζڕ࣠ऀࠩ෈᧯Δڶᤛሽࢨထ־ऱٲᙠΖ



ᓮլ૞ኙء๻ໂၞ۩ࣈ࠵Εଥ෻ΕޏທΖڶᤛሽࡉ࿇س־߀ऱٲᙠΖ



ൎࠫ۩੡



ᓮലء๻ໂऱሽᄭ༺ᙰൕۻࣚᕴՂࢸՀΖڶ࿇س־߀ࡉᤛሽऱٲᙠΖ



ኙॺ௽ࡳऱԫ౳ࠌشृऱ۩੡ၞ۩ਐقΖᓮਊᅃᎅࣔၞ۩ᖙ܂Ζ



127(7KLVHTXLSPHQWKDVEHHQWHVWHGDQGIRXQGWRFRPSO\ZLWKWKHOLPLWVIRUD&ODVV

$GLJLWDOGHYLFHSXUVXDQWWR3DUWRIWKH)&&5XOHV7KHVHOLPLWVDUHGHVLJQHG

WRSURYLGHUHDVRQDEOHSURWHFWLRQDJDLQVWKDUPIXOLQWHUIHUHQFHZKHQWKHHTXLSPHQWLV

RSHUDWHGLQDFRPPHUFLDOHQYLURQPHQW7KLVHTXLSPHQWJHQHUDWHVXVHVDQGFDQUDGLDWH

UDGLRIUHTXHQF\HQHUJ\DQGLIQRWLQVWDOOHGDQGXVHGLQDFFRUGDQFHZLWKWKH

LQVWUXFWLRQPDQXDOPD\FDXVHKDUPIXOLQWHUIHUHQFHWRUDGLRFRPPXQLFDWLRQV2SHUDWLRQ

RIWKLVHTXLSPHQWLQDUHVLGHQWLDODUHDLVOLNHO\WRFDXVHKDUPIXOLQWHUIHUHQFHLQ

ZKLFKFDVHWKHXVHUZLOOEHUHTXLUHGWRFRUUHFWWKHLQWHUIHUHQFHDWKLVRZQH[SHQVH



ຍਢ˖˟˔˦˦ʳ˄ʳ˟˔˦˘˥ʳˣ˥ˢ˗˨˖˧Ζᇠᑑ᧘၀࣍ߓอऱփຝ٠጗Ζʳ



ࣹრΚʳ ءข঴ຏመڍ塒ऱ࿏᧯ᑓิ༼ࠎ࿏᧯୲ᙑࢤ౨Ζ܀ਢຍࠀլ।ق౨ജঅᢞݙ٤୲ᙑΖ

ڕΔڇאՀൣउՀױ౨࿇سᰳᖲΚʳ

Ωʳຌ᧯࿇سીࡎਚᎽΖʳ

Ωʳڍ塒࿏᧯ᠨֱ݁࿇سਚᎽΔլ౨ሎ۩Ζʳ

Ωʳழᤪขسᕴᒵሁࢨփຝຑ൷હࣨ࿛ॺڍ塒ցٙ࿇سીࡎਚᎽΖʳ

– ಾᣆੌᢛ୘♽⛔⊛AC㔚Ḯ

CLASS 1

LASER PRODUCT

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

ᴾ

This class A digital apparatus meets all requirements of the Canadian Interference-Causing

Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel

brouilleur du Canada.

CE Statement

Warning: This is a Class A product. In residential environment, this product may cause radio

interference, in which case the user may be required to take adequate measures (EN55022).

This system is classified as a CLASS 1 LASER PRODUCT. This label id located on

the internal CD-ROM installed in your system.

NOTE: This product provides resistance against hardware faults with its redundant hardware

modules. However, this does not mean complete fault-tolerance is assured. For example,

there is a risk of system down when:

– A fatal fault occurs in software.

– Both modules within a redundant hardware pair break down.

– A fatal fault occurs in a non-redundant component, such as the clock generator circuitry

or the interconnect backplane.

– The entire system is cut off from AC power.

CLASS 1

LASER PRODUCT

Trademarks and Patents

NEC EXPRESSBUILDER and NEC ESMPRO are trademarks of NEC Corporation.

Microsoft, Windows, Windows Server, Windows NT, and MS-DOS are registered trademarks of

Microsoft Corporation in the United States and other countries.

Intel and Pentium are registered trademarks of Intel Corporation.

AT is a registered trademark of International Business Machines Corporation in the United States

and other countries.

Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of Adobe Systems

Incorporated.

Datalight is a registered trademark of Datalight, Inc. ROM-DOS is a trademark of Datalight, Inc.

Xeon is a trademark of Intel Corporation in the United States. DLT and DLTtape are trademarks of

Quantum Corporation in the United States. QLogic and its logo are trademarks of QLogic

Corporation in the United States. Fast!UTIL is a trademark of QLogic Corporation in the United

States.

Avocent and Dambrackas Video Compression (DVC) are trademarks or registered trademarks of

Avocent Corporation in the United States and other countries.

Mozilla is a trademark of Mozilla Foundation.

Netscape is a trademark or registered trademark of Netscape Communications Corporation in the

United States and other countries. Java is a trademark or registered trademark of Sun Microsystems,

Inc. in the United States and other countries.

All other product, brand, or trade names used in this publication are the trademarks or registered

trademarks of their respective trademark owners.

Microsoft Windows Server 2003 R2 32-bit Standard Edition operating system, Microsoft Windows

Server 2003 R2 32-bit Enterprise Edition operating system, Microsoft Windows Server 2003

Standard Edition operating system and Microsoft Windows Server 2003 Enterprise Edition

operating system are called Windows Server 2003 for short. Microsoft Windows 2000 Server

operating system, Microsoft Windows 2000 Advanced Server operating system and Microsoft

Windows 2000 Professional operating system are called Windows 2000 for short. Microsoft

Windows NT Server network operating system version 3.51/4.0 and Microsoft Windows NT

Workstation operating system version 3.51/4.0 are called Windows NT for short. Microsoft

Windows Millennium Edition Operating System is called Windows Me for short. Microsoft

Windows 98 operating system is called Windows 98 for short. Microsoft Windows 95 operating

system is called Windows 95 for short.

Names used with sample applications are all fictitious. They are unrelated to any existing product

names, names of organizations, or individual names.

The Dambrackas Video Compression algorithm from Avocent Corporation is used for ft Remote

Management Card.

U.S. Patent Numbers: 5,732,212, 5,937,176, 6,633,905, 6,681,250, 6,701,380 and other patents

pending

Taiwanese Patent Number: 173784

European Patent Number: 0 740 811

Notes:

(1) No part of this manual may be reproduced in any form without prior written permission of

NEC Corporation.

(2) The contents of this manual are subject to change without prior notice.

(3) The contents of this manual shall not be copied or altered without prior written permission of

NEC Corporation.

(4) All efforts have been made to ensure the accuracy of all information in this manual. If you find

any part unclear, incorrect, or omitted in this manual, contact the sales agent where you

purchased this product.

(5) NEC assumes no liability arising from the use of this product, nor any liability for incidental or

consequential damage arising from the use of this manual regardless of (4) above.

iii

Preface

Welcome to the NEC Express5800/ft series.

NEC Express5800/ft series is a “fault-tolerant (ft)” server focusing on “high reliability” in terms of

fault-tolerance, in addition to “high performance,” “scalability,” and “general versatility” provided

by NEC Express5800 series. In the event of trouble, its dual configuration will allow the system to

instantaneously isolate the failed parts to assure non-stop running; operation will be moved

smoothly from one module to the other, minimizing damage to it. You can use NEC Express5800/ft

series in a mission-critical system where high availability is required. By the use of Windows Server

2003 operating system, it also provides outstanding openness for general-purpose applications, etc.

To make the best use of these features, read this User's Guide thoroughly to understand how to

operate NEC Express5800/ft series.

About This User’s Guide

This User's Guide helps a user to properly setup and use the product. Consult this guide when you

set up the product.

Keep this manual and the separate volume of User’s Guide handy.

This User's Guide is intended for users who have a good knowledge on the basic use of Windows

operating systems and general I/O devices such as a keyboard and mouse.

How to Use This User's Guide

This guide explains the procedures you should perform before you begin system operation after you

purchased the product. Read the guide in order from Chapter 1. If you perform procedures

according to this guide, you will set up the product properly.

Chapter 4 describes how to install the operating system. Chapter 5 describes post-installation

procedures. Chapter 6 explains how to troubleshoot if you cannot set up the product properly. Refer

to “SYSTEM REPAIR” on page 6-2 for details about system configurations and repairs of this

product. Refer to “TROUBLESHOOTING” on page 6-14 if you feel you failed to set up the

product.

See this User’s Guide for details of this product’s operation, and functions and operations of the

hardware and the system.

Additional symbols

The following symbols are used throughout this User's Guide in addition to the caution symbols

described at the beginning.

IMPORTANT:

Important points or instructions to keep in mind when using the

server or software

CHECK:

Something you need to make sure when using the server or

software

TIPS:

Helpful information, something useful to know

ᴾ

About our Web Service

Information on NEC Express5800/ft series including modification modules is also available on our

web site, NEC Express5800 Web Site Asia Pacific, at

http://www.nec.co.jp/express/index.html

Contents

Preface...............................................................................................................................................iii

About This User’s Guide .................................................................................................................iv

How to Use This User's Guide.......................................................................................................iv

Additional symbols .........................................................................................................................v

About our Web Service................................................................................................................... v

CHAPTER 1 BEFORE USING ....................................................................................... 1-1

NOTES FOR SAFE HANDLING.................................................................................................1-2

Warning Labels............................................................................................................................1-2

CPU/IO Modules .........................................................................................................................1-4

PRECAUTIONS FOR SAFETY...................................................................................................1-6

General.........................................................................................................................................1-6

Use of Power Supply and Power Cord.........................................................................................1-7

Installation, Relocation, Storage and Connection ........................................................................1-8

Cleaning and Handling of Internal Devices .................................................................................1-9

During Operation .......................................................................................................................1-10

Rack-mount Model (Model 320Fb-MR)....................................................................................1-11

ڜ٤ࣹრࠃႈ................................................................................................................................1-13

ԫ౳ࣹრࠃႈ ...........................................................................................................................1-13

ࠌشሽᄭ֗ሽᄭᒵࣹრࠃႈ....................................................................................................1-14

ڜᇘΔฝ೯Δঅጥ֗ຑ൷ࣹრࠃႈ........................................................................................1-15

ᖞ෻֗ᖙ܂փຝ๻ໂழऱࣹრࠃႈ........................................................................................1-16

ᖙ܂ࣹრࠃႈ ...........................................................................................................................1-17

ᖲਮڤۻࣚᕴऱࣹრࠃႈ........................................................................................................1-18

UNPACKAGING .........................................................................................................................1-20

Accessories ................................................................................................................................1-20

CHAPTER 2 ABOUT OPERATING SYSTEM ................................................................ 2-1

INSTALLING Windows Server 2003...........................................................................................2-2

About OS Installation ..................................................................................................................2-2

CHAPTER 3 INSTALLING SERVER.............................................................................. 3-1

INSTALLATION ...........................................................................................................................3-2

Tower Model................................................................................................................................3-2

Rack-mount Model ......................................................................................................................3-4

vii

Connection...................................................................................................................................3-7

CHAPTER 4 WINDOWS SETUP ....................................................................................4-1

Express Setup .................................................................................................................................4-2

SETUP FLOW ...............................................................................................................................4-3

Step 1: Things Required for Setup ...............................................................................................4-4

Size of the Partition to be Created ...............................................................................................4-5

Step 2: Prepare for Express Setup................................................................................................ 4-6

2-1: Prepare NEC Express5800/ft series......................................................................................4-6

Step 3: Disable Boot Monitoring Function ..................................................................................4-9

Step 4: Start the Express Setup...................................................................................................4-14

Flow of Setup Procedures..........................................................................................................4-15

Setup Procedures ....................................................................................................................... 4-16

Step 5: Set Dual LAN Configuration..........................................................................................4-23

Overview ...................................................................................................................................4-23

NEC Express 5800/Fault Tolerant Server Series Duplication Rule........................................... 4-24

Dual Configuration Setup.......................................................................................................... 4-24

Step 6: Set Dual Disk Configuration ..........................................................................................4-29

Setting Dual Disk Configuration by Disk Management ............................................................4-29

Step 7: Update Software .............................................................................................................. 4-32

Step 8: Connect and Configure Options ....................................................................................4-32

Step 9: Create Volume.................................................................................................................4-33

Step 10: Set Network for NEC ESMPRO Agent.......................................................................4-33

Step 11: Enable Boot Monitoring Function ...............................................................................4-35

Step 12: Make Settings for Failure Management...................................................................... 4-36

Set Memory Dump (Debug Information) .................................................................................. 4-36

Set Dr. Watson........................................................................................................................... 4-41

Install a Network Monitor .........................................................................................................4-42

Set Recovery Console................................................................................................................4-43

Step 13: Back up System Information........................................................................................ 4-44

CHAPTER 5 PROCEDURES AFTER COMPLETION OF INSTALLATION...................5-1

INSTALLING MANAGEMENT UTILITIES ............................................................................ 5-2

viii

NEC ESMPRO Agent..................................................................................................................5-2

NEC ESMPRO Manager ...........................................................................................................5-11

NEC DianaScope .......................................................................................................................5-12

CONFIRMATION OF THE GeminiEngine Control Software VERSION ............................5-13

CAUTIONS FOR APPLYING Windows Service Pack ............................................................5-14

CHANGING THE COLOR QUALITY OF DISPLAY TO 32 BIT ........................................5-14

COMPRESSING A SYSTEM DRIVE .......................................................................................5-15

ABOUT Windows Update (APLYING SECURITY PATCKES) ............................................5-15

CHAPTER 6 TROUBLESHOOTING .............................................................................. 6-1

SYSTEM REPAIR .........................................................................................................................6-2

Preparation...................................................................................................................................6-4

Starting up Recovery Console......................................................................................................6-5

Updating the System....................................................................................................................6-8

Installing GeminiEngine Control Software................................................................................6-13

TROUBLESHOOTING...............................................................................................................6-14

Problems with NEC EXPRESSBUILDER ................................................................................6-14

Problems with Windows Setup..................................................................................................6-15

About the Express Setup............................................................................................................6-17

Problems with NEC ESMPRO Setup ........................................................................................6-21

Problems with System Repair ....................................................................................................6-22

APPENDIX A ABOUT SERVICES .................................................................................A-1

Chapter 1

Before Using

This chapter includes information necessary for proper and safe operation of the server, the main

unit and its accessories. Go through this chapter before you start setup of the product.

1-2 Before Using

NOTES FOR SAFE HANDLING

The following section describes necessary information to use the product properly and safely.

Warning Labels

Warning labels are placed in certain parts of the system so that the user stays alert to possible risks

(Do not remove or damage these labels).

If some label is missing, about to peel off, or illegible, contact your sales agent.

The figures below show locations of the labels on the server.

Tower model

Fron

Rear

Page is loading ...

NEC N8800-096F User manual

Brand: NEC

Model: N8800-096F

Category: Soundbar speakers

Type: User manual

This manual is also suitable for

Download PDF

report

NEC N8800-096F User manual

This manual is also suitable for

NEC N8800-096F User manual

Related papers

Other documents