Autonics PSAN-01CA Series User manual

1. Fail-safe device must be installed when using the unit with machinery that may cause serious injury or

substantial economic loss. (e.g. nuclear power control, medical equipment, ships, vehicles, railways,

aircraft, combustion apparatus, safety equipment, crime/disaster prevention devices, etc.)

 Failuretofollowthisinstructionmayresultinre,personalinjury,oreconomicloss.

2. Install on a device panel or to a pressure port directrly to use.

 Failuretofollowthisinstructionmayresultinre.

3. Do not connect, repair, or inspect the unit while connected to a power source.

 Failuretofollowthisinstructionmayresultinre.

4. Check 'Connections' before wiring.

 Failuretofollowthisinstructionmayresultinre.

5. Do not disassemble or modify the unit.

 Failuretofollowthisinstructionmayresultinre.

DIGITALPRESSURESENSOR(Pneumatictype)

PSAN SERIES

Safety Considerations

Warning

Caution

Output Operation Mode

Parameter Setting

Preset Setting

Input/Output Circuit and Diagram

Installation

Error

Functions

I N S T R U C T I O N M A N U A L

ThankyouverymuchforselectingAutonicsproducts.

For your safety, please read the following before using.

※Pleasekeeptheseinstructionsandreviewthembeforeusingthisunit.

※Thefollowingisanexplanationofthesymbolsusedintheoperationmanual.

Caution:Injuryordangermayoccurunderspecialconditions.

※Pleaseobservethecautionsthatfollow;

Warning Seriousinjurymayresultifinstructionsarenotfollowed.

Caution Productmaybedamaged,orinjurymayresultifinstructionsarenotfollowed.

Specications Setting

Major Products

Display Description Countermeasures

ERR1

Whenexternalpressureisinputwhileadjustingzeropoint.

Tryagainafterremovingexternalpressure.

ERR2 Whenoverloadisappliedoncontroloutput Removeoverload.

ERR3 WhensettingconditionisnotmetinAutosensitivity

settingmode.

Checksettingconditionsandsetproper

settingvalues.

LLLL WhenappliedpressureexceedsLow-limitofdisplay

pressurerange. Applypressurewithindisplaypressure

range.

HHHH WhenappliedpressureexceedsHigh-limitofdisplay

pressurerange.

-HH-,-LL-,

-HL-

Autoshiftcorrectionerror. Setthecorrectedsettingvaluewithin

settingpressurerange.

Hysteresis mode[ HYS.M]

Itisabletosetcertainvalueforpressuredetection

level[ST1,ST2]andhysteresis[HYS1,HYS2].

Hysteresis mode

Hysteresis-Window comparison output mode

Zero point adjustment

1.Pleasepress + keysforover1sec.atthe

sametimeputtinganappliedpressureinstateofthe

atmosphericpressure.

2.Whenthezeropointadjustmentiscompleted,itwill

display)0 andreturntoRUNmodeautomatically.

※Ifexecutingzeropointadjustmentonexternal

pressurebeingatpressureport[ERR1] flashes 5

times.Pleaseexecuteitintheatmosphericpressure

afterremovingexternalpressure.

※Pleaseexecutezeropointadjustmentregularly.

※1:PSAN- H- DisplayedonlywhenD-IN is

set to SHFT.Autoshiftreferencepressurecanbeset

withindisplayerrorrange.

(Low_Range≤SH.IN ≤High_Range)

•Low_Range=Min.displaypressure-Min.preset

setting value

•High_Range=Max.displaypressure-Max.preset

setting value

※Ifpressing + keysforover1sec.incaseofHigh

peak/Lowpeak/Autoshiftreferencepressurevalue,

settingvaluewillbeeraseandreturntonextoperation.

※ [ RUN]flashestwice,thenreturntoRUNmode.

Peak Hold / Auto Shift Check/Change

Hysteresis-window comparison output mode[ HY-W]

①Itisavailabletosethysteresismode[ST1, HYS1]

andwindowcomparisonoutputmodewhenboth

hysteresismodeandwindowcomparisonoutput

mode[LOW, HIGH]arenecessary.

②Detectionhysteresisisfixedtomin.displayrange.

Forced output control mode[ fOUT]

①UsedtodisplaypressurewithforciblyholdingcomparingoutputOFFregardlessofsettingvalue.

②Inparametersetting,ifoutputoperationmodesetting[OUtN]ischangedto[fOUT],forcedoutputcontrol

modeisoperated.

③OUT1,2canbeON/OFFmanuallybypressing , keyWhiletheforcedoutputcontrolmodeisapplied.

Analog output type (Voltage output PSAN-□□□□V-□, Current output PSAN-□□□□A-□)

Hold / Auto Shift input type (PSAN-□□□□H-□)

1.Pressureportisdividedasbasicandoptionspecification.

Therefore,besurethattousecommerciallyavailableone

touchfitting.(Standard:Rc1/8",Option:NPT1/8",R1/8")

2.Pleaseconnectitbyusingspanner(12mm)atthe

metalpartinordernottooverloadonthebodywhen

connectingonetouchfitting.

3.TwodifferentfixingbracketsareprovidedforPSAN

model.Selectproperonewithconsideringyour

applicationenvironments.

4.Atfirst,pleaseunscrewhexagonwrenchboltand

assemblethebracketonthisunitbyfixinghexagon

thewrenchbolt.In this case, tightening torque of

hexagon wrench should be max. 3N.m. It may cause

mechanical problems.

5.Panelbracket(PSO-B02)andfrontprotection

cover(PSO-P01)areoptionaltosell.

Pleaseseethefigureforinstallation.

●NPNopencollectoroutputtype ●PNPopencollectoroutputtype

Window comparison output mode[ WIN]

①Itisabletosettherangeforhigh[HI-1,HI-2]/

low[LO-1, LO-2]limitofpressuredetectionlevelwhen

itisrequiredtodetectpressureatacertainrange.

②Detectionhysteresisisfixedtomin.displayrange.

Automatic sensitivity setting mode

Automatic sensitivity setting mode[ AUTO]

①Thisfunctionistosetpressuredetectionlevel

totheproperpositionautomatically.Itissetby

appliedpressurefromtwopositions[ST1,ST2].

②Detectionhysteresisisfixedtomin.displayrange.

③Thepressuredetectionlevel[SET] is shown in

thefollowingcalculation.

Pressure unit change

PSAN-V01C(P)andPSAN-C01C(P)has7kindsofpressureunit,PSAN-01C(P)andPSAN-1C(P)has5kinds

ofpressureunit.Pleaseselecttheproperunitforapplication.

• PSAN-V01C(P),PSAN-C01C(P):kPa,kgf/cm2,bar,psi,mmHg,inHg,mmH2O

• PSAN-01C(P),PSAN-1C(P):MPa,kPa,kgf/cm2,bar,psi

※WhenusingmmH2Ounit,pleasemultiplydisplayvalueby100.

Output mode change

Thereare5kindsofcontroloutputmodeinordertorealizethevariouspressuredetection.

• Hysteresismode[HYsM]:Whenneededtochangehysteresisfordetectingpressure.

• Windowcomparisonoutputmode[WIN]:Whenneededtodetectpressureincertainarea.

• Hysteresis-Windowcomparisonoutputmode[HY-W]:Whenbothhysteresismodeandwindowcomparison

outputmodearerequired.

• Automaticsensitivitysettingmode[AUTO]:Whenneededtosetdetectionsensitivityautomaticallyatproper

position.

• Forcedoutputcontrolmode[fOUT]:Whenneededtodisplaypressurewithremainingcomparisonoutput

OFFregardlessofsettingvalue.

Control output change

TypeofcontroloutputforOut1andOut2canbeabletosetNormallyOpenandNormallyClosed.

※NotethatNormallyOpenandNormallyClosedprovideoppositeoutput.

Response time change(chattering prevention)

Itcanpreventchatteringofcontroloutputbychangingresponsetime.

Itisabletoset5kindsofresponsetime(2.5ms,5ms,100ms,500ms,1000ms)andiftheresponsetimeis

gettinglonger,thedetectionwillbemorestablebyincreasingthenumberofdigitalfilter.

Analog output scale setting and Hold/Auto Shift setting

• Analogvoltageoutputscalesetting:Thescalefunctionforanalogoutputvoltage(1-5VDC)isnotfixedtothe

ratedpressurerange.ItcanbechangedforUser'sapplication.Analogoutputis1-5VDCwithinthepressure

rangefromthepressurepoint[A-1V]for1VDCtothepressurepoint[A-5V]for5VDC.

• Analogcurrentoutputscalesetting:ThescaleforanalogoutputCurrent(DC4-20mA)isnotfixedtotherated

pressurerange.ItcanbechangedforUser'sapplication.Analogoutputis4-20mAwithinthepressurerange

fromthepressurepoint[A-04]for4mAtothepressurepoint[A-20]for20mA.

• Hold/AutoShiftinputsetting

- Holdfunction:AfunctiontoholdPVandControloutputwhilesignalisinput.

- AutoShiftfunction:Afunctiontocompensatethesettingvalueforchangedvalueofreferencepressureas

thresholdlevelifreferencepressureofthedevicechanges.

Key lock

Thekeylockfunctionpreventskeyoperationssothatconditionssetineachmode.[preset/parametermodeare

notinadvertentlychanged.Thereare2kindsofkeylockfunctionsavailable.

• LOC1:Allkeysarelocked;thereforeitisnotavailabletochangeparametersettings,presetvalue,zero

adjustment,High/LowpeakcheckandSH.IN datainitialization.(Locksettingchangeisavailable)

• LOC2:Partiallylockedstatus;thereforeitisnotavailabletochangeparametersettingsonly(Locksetting

changeisavailable).Othersettingsarestillavailable.

• OFF:Allofthesettingisavailable,allkeysareunlocked.

Zero point adjustment

Thezeropointadjustmentfunctionforciblysetsthepressurevalueto"Zero"whenthepressureportisopened

toatmosphericpressure.Whenthezeroadjustmentisapplied,analogoutput[VoltageorCurrent]ischanged

bythisfunction.(Press + keysover1sec.inRUNmode.)

High Peak / Low Peak Hold Function

Thisfunctionistodiagnosismalfunctionofthesystemcausedbyparasiticpressureortocheckthrough

memorizingthemax./min.pressureoccurredfromthesystem.

※1:(P)isPNPoutputtype, ofmodelnameisaspressureport.

Rc1/8:PT1/8"model(standard),NPT1/8:NPT1/8"model(option),

R1/8:PT1/8"model(Option)

※2:Inhysteresisoutputmode,detectiondifferenceisvariable.

※3:Itisallowedtoselectoneanalogoutputtypeonly.

※4:Resolution(1000/2000)ofmin.Displayintervalisautomatically

selecteddependonpressureunits.

※5:Thisweightiswithpackagingandtheweightinparenthesesis

onlyunitweight.

※F.S.:Ratedpressure.

※Theremaybe±1digiterrorinhysteresis

bypressureunitcalculationerror.

※ForusingmmH2Ounit,multiplydisplay

valueby100.

※Environmentresistanceisratedatno

freezingorcondensation.

(ST1+ST2)

SET

※Ifthekeylockisset(lock1orlock2),unlockthekeylockbeforesettingparameters.

※ Press , keytochangesettingvalues.

※ Press keytosavesettingvalueineachparameterandmovetonextparameters.

※Whenpressing keyfor3secinthemiddleofparametersetting,currentsettingvaluewillbesaved

and[RUN]willflashtwice,thenreturnedtoRUNmode.

※ [ RUN]flashestwicewhenreturningtoRUNmode.

※ Press , keytochangesettingvalues.

※ Press keytosavesettingvalueineachparameterandmovetonextparameters.

※Ifthereisnoadditionalkeyoperationwithin60sec.while

setting,itisreturnedtoRunmode(Exceptforforceoutput

mode).Previoussetvaluesareremained.

※Incaseofchangingoutputoperationmode,nopreset

valueswillbeinitialized.Instead,previousoutputoperation

settingswillbecomethepresetvalues.

※Whenchangingpressuredisplayunit,resolutionandHold/

AutoShiftinputfunction,presetvalueswillbeinitializedas

shownthetablebelow.(Whenchangingpressuredisplay

unit,presetvaluewillbeautomaticallyswitchedtochanged

pressureunit.)

※Ifthereisnoadditionalkeyoperationwithin60sec.whilesetting,currentsettingvalueisnotvalidand

previoussettingvaluewillberemained.

< Preset Default >

※Whenusingtheforcedoutputfunction,Hold/Autoshift

functionisnotavailabletouseinHold/Autoshiftmode.

(unit:kPa)

※Min.displaypressure

≤[ST1]≤Max.display

pressure-1%ofrated

pressure

※[ ST1]+1%ofrated

pressure≤[ST2]≤

Max.displaypressure

※[ SET]

= ([ ST1]+[ ST2])/2

※Press , key for

manualadjustment

※ [ ERR3] Error flashes 3 times in case setting

conditionsarenotmet,resettingisonstandby.

※ PSAN series has 5 kinds of output operation mode, please use proper output operation mode in

accordance with detection.

Over current

protection

circuit

Over current

protection

circuit

(Brown)+V

(Blue)0V

(Black)OUT1

(White)OUT2

12-24VDC

Load

※ :Forvoltageoutputtypeonly.

1kΩ

Main circuit

(Orange)

Analogoutput

voltage/current

Pressuretype Gaugepressure

Negativepressure Standardpressure Compoundpressure

Model※1

Voltageoutput PSAN-V01C(P)V- PSAN-01C(P)V- PSAN-1C(P)V- PSAN-C01C(P)V-

Currentoutput PSAN-V01C(P)A- PSAN-01C(P)A- PSAN-1C(P)A- PSAN-C01C(P)A-

Hold/Autoshiftinput PSAN-V01C(P)H- PSAN-01C(P)H- PSAN-1C(P)H- PSAN-C01C(P)H-

Ratedpressurerange 0.0to-101.3kPa 0.0to100.0kPa 0to1,000kPa

-101.3kPato100.0kPa

Displaypressurerange 5.0to-101.3kPa -5.0to110.0kPa -101.3to1,100kPa

-101.3kPato110.0kPa

Min.displayunit 0.1kPa 0.1kPa 1kPa 0.1kPa

Max.pressurerange 2timesofrated

pressure

2timesofrated

pressure

1.5timesofrated

pressure

2timesofrated

pressure

Applieduid Air,Non-corrosivegas

Powersupply 12-24VDCᜡ±10%(rippleP-P:Max.10%)

Currentconsumption Max.50mA(AnalogCurrentOutputtypeMax75mA)

Controloutput

NPNorPNPopencollectoroutput

•Loadvoltage:Max.30VDCᜡ•Loadcurrent:Max.100mA

•Residualvoltage-NPN:Max.1VDCᜡ,PNP:Max.2VDC

Hysteresis※2Min.displayrange

Repeaterror ±0.2%F.S.±Min.displayrange

Responsetime Selectable2.5ms,5ms,100ms,500ms,1000ms

Shortcircuitprotection

Built-in

Analog

output※3

Voltageoutput

•Outputvoltage:1-5VDCᜡ±2%F.S.•Linear:Max.±1%F.S.•Outputimpedance:1kΩ

•Zeropoint:Max.1VDCᜡ±2%F.S.•Span:Max.4VDCᜡ±2%F.S.•Responsetime:50ms

•Resolution:Automaticallychangedto1/1000or1/2000bypressureunit

Currentoutput

•Outputcurrent:DC4-20mA±2%•Linear:Max.±1%F.S.

•Zero-point:Max.DC4mA±2%F.S.•Span:Max.DC16mA±2%F.S.•Responsetime:70ms

•Resolution:Automaticallychangedto1/1000or1/2000bypressureunit

Displaymethod 7segmentLEDDisplay

Min.Displayinterval※4

Resolution

Pressure unit

1000 2000 1000 2000 1000 2000 1000 2000

MPa

- -

0.001

- - -

kPa 0.1

0.1

- -

0.1

kgf/cm20.001

0.001

0.01

- -

0.001

bar 0.001

0.001

0.01

- -

0.001

psi

0.01 - 0.01 - 0.1

0.02

mmHg

0.4

0.8

inHg

0.02

0.03

mmH₂O0.1

- -

0.1

Displayaccuracy 0℃to50℃:Max.±0.5%F.S.,-10to0℃:Max.±1%F.S.

Dielectric strength 1000VAC50/60Hzfor1minute

Insulation resistance Over50MΩ(at500VDCmegger)

Vibration

1.5mmamplitudeatfrequencyof10to55Hz(for1min.)ineachofX,Y,Zdirectionfor2hours

Environ-

ment

Ambienttemp. -10to50℃,storage:-20to60℃

Ambienthumi. 30to80%RH,storage:30to80%RH

Protection IP40(IECspecification)

Material Frontcase:PC,Rearcase:PC,Pressureport:NickelPlatedBrass

Cable Connectorcable(Ø4mm,5-wire,Length:2m)

(AWG24,Corediameter:0.08mm,Numberofcores:40,Insulatoroutdiameter:Ø1mm)

Approval

Weight

※

Approx.165g(approx.80g)

ST2

HYS2

ST1

HYS1

Pressure

Time

ST2/HYS2

ST1/HYS1

ST2/HYS2

OUT1N.O.

OUT2N.O.

OUT1N.C.

OUT2N.C.

RUN mode

Flashing

in turn

fOUT

Currentpressure

8#1

RUN modeRUN mode Forced output control mode

operation status

OUT1

OUT2

Time

OFF

Press key

over3sec.

Press key

over3sec.

Press

keysover1sec.

Press key

Parameter

setting

Pressure

unit setting

Output

operation

modesetting

Output

typesetting

Response

time setting

Key lock

setting

Analogoutputscaleand

Hold/AutoShiftinputsetting

Peakhold Highpeak

value check

Lowpeak

value check

Autoshiftinputsetting

(IncaseofHold/Autoshiftinputtypemodel)

Zero-point

adjustment Zero-pointadjustment

Preset value

setting

Detectionlevel1setting(out1)

Detectionlevel2setting(out2)

Forcedoutput

controlmode

setting

Theforcedoutputcontrolmodeisappliedwithpressign keyafterselectingforcedoutputcontrol

mode[fOUT]inoutputoperationmode[OUtM]parameter.Formoredetailedinformation,

referto'●Forcedoutputcontrolmode'' Outputoperationmode'

RUNmode

※1: Min.displayrange

Pressure

Time

LO-1/HI-1

LO-2/HI-2

OUT1N.O.

OUT2N.O.

OUT1N.C.

OUT2N.C.

※1

HI-2

HI-1

LO-2

LO-1

Time

※1:Min.displayrange

Pressure

Time

LOW/HIGH

ST1/HYS1

LOW/HIGH

OUT1N.O.

OUT2N.O.

OUT1N.C.

OUT2N.C.

※1

ST1

HYS1

LOW

HIGH

Time

※1:Min.displayrange

Pressure

Time

SET=(ST1+ST2)/2

ST1/ST2

SET

ST1/ST2

OUT1N.O.

OUT2N.O.

OUT1N.C.

OUT2N.C.

※1

ST2

SET

ST1

flashing

in turn

flashing

in turn

flashing

in turn

flashing

in turn

flashing

in turn flashing

in turn

flashing

in turn

flashing

in turn flashing

in turn

flashing

in turn

flashing

in turn

※IncaseofusingmmH2Ounit,

multiply100bydisplayvalue.

※Incaseofstandardpressure

typemodel,[MPA],[KPA],[KGF],

[ BAR],[PSI]parametersare

displayedonly.

Parameter OUT1output OUT2output

1O2O

NormallyOpen NormallyOpen

1O2C

NormallyOpen NormallyClosed

1C2O

NormallyClosed NormallyOpen

1C2C

NormallyClosed NormallyClosed

※Unit: ms

Analog voltage output

(PSAN-□□□□V-□)

Analog current output

(PSAN-□□□□A-□)

Hold/Shift input

(PSAN-□□□□H-□)

SelectHold(Referto" Function")

※1:Setrange:Min.ratedpressure≤[A-1V,A-04]≤90%ofratedpressure

※2: Set range : [ A-1V,A-04]+10%ofratedpressure≤[A-SV,A-20]≤Max.ratedpressure

※See setting Function key lock function for more

details.

Press key

over3sec.

Press key

over3sec.

※1※1

※2※2

RUN mode

Pressure unit

Outputoperation

mode

Output

Responsetime

1VScale

5VScale

4mA Scale

20mAScale

Externalinputfunction

Controloutputfor

Auto shift function

Key lock

(MPa) (KPa) (kgf/cm

)(bar)

(psi)

(mmH

O) (inHg) (mmHg)

MPA

H2O

KPA

INHG

KGF

MMHG

BAR

PSI

UNIT

OUtM

1O2O

1O2C

100

1C2O

500

1C2C

Hysteresis

mode

Window

comparison

outputmode

Auto sensitivity

settingmode Forcedoutput

controlmode

Hysteresis-Window

comparisonoutput

mode

HYsM WIN HY-W AUTO fOUT

1000

NoNC

SPD

A-04 HOLD

OUT1

ALL

D-IN

ShOTA-20

A-1V )0 )0 SHFT

OUT210)0A-5V 10)0

OFFLOCK LOC1 LOC2

flashing

in turn

flashing

in turn

flashing

in turn

flashing

in turn

※Set range :

Min.displaypressure

＜ [ ST1]≤Max.display

pressure

※Set range :

Min.displaypressure

≤[HYS1] ＜ [ ST1]

※Set range :

Min.displaypressure

＜ [ ST2]≤Max.display

pressure

※Set range :

Min.displaypressure

≤[HYS2] ＜ [ ST2]

Hysteresislevel1

Pressuredetection

level 2

Pressuredetection

level 1

Hysteresislevel2

ST1 2)0

HYS1 1)0

ST2 4)0

HYS2 3)0

RUN mode

flashing

in turn

flashing

in turn

flashing

in turn

Pressuredetection

level 1

Pressuredetection

level 2

Auto setting value

ST1 1)0

ST2 2)0

STT 1%0

RUN mode

Window comparison output mode

※Set range :

Min.displaypressure

≤[LO-1]≤Max.display

pressure-(3×Min.display

interval)

※Set range :

[ LO-1]+(3×Min.display

interval)≤[HI-1]

≤Max.displaypressure

※Set range

Min.displaypressure≤

[ LO-2]≤Max.display

pressure-(3×Min.display

interval)

※Set range

[ LO-2]+(3×Min.display

interval)≤[HI-2]

≤Max.displaypressure

flashing

in turn

flashing

in turn

flashing

in turn

flashing

in turn

Low-limitvalueof

Pressuredetectionlevel1

Low-limitvalueof

Pressuredetectionlevel2

High-limitvalueof

Pressuredetectionlevel1

High-limitvalueof

Pressuredetectionlevel2

LO-1 1)0

HI-1 2)0

LO-2 3)0

HI-2 4)0

RUN mode

※Set range

Min.displaypressure

＜ [ ST1]≤Max.display

pressure

※Set range

Min.displaypressure

≤[HYS1] ＜ [ ST1]

※Set range

Min.displaypressure

≤[LOW]≤Max.display

pressure-(3×Min.display

interval)

※Set range

[ LOW]+(3×Min.display

interval)≤[HIGH]

≤Max.displaypressure

flashing

in turn

flashing

in turn

flashing

in turn

flashing

in turn

ST1 1)0

HYS1 2)0

LOW 3)0

HIGH 4)0

RUN mode

Pressuredetection

level 1

Hysteresislevel1

Low-limitvalueof

Pressuredetectionlevel2

High-limitvalueof

Pressuredetectionlevel2

Output

mode

Negative

pressure

0.0to-101.3

Standard

pressure

0.0to100.0

Standard

pressure

0to1,000

Compound

pressure

-101.3to100.0

HYS.M

ST1

:-50.0

ST1

:50.0

ST1

:500

ST1

:50.0

HYS1

:0.0

HYS1

:0.0

HYS1

:-50.0

ST2

:-50.0

ST2

:50.0

ST2

:500

ST2

:50.0

HYS2

:0.0

HYS2

:0.0

HYS2

:-50.0

WIN

LO-1

:0.0

LO-1

:0.0

LO-1

:-50.0

HI-1

:-50.0

HI-1

:50.0

HI-1

:500

HI-1

:50.0

LO-2

:0.0

LO-2

:0.0

LO-2

:-50.0

HI-2

:-50.0

HI-2

:50.0

HI-2

:500

HI-2

:50.0

HY-W

ST1

:-50.0

ST1

:50.0

ST1

:500

ST1

:50.0

HYS1

:0.0

HYS1

:0.0

HYS1

:-50.0

LOW

:0.0

LOW

:0.0

LOW

:500

LOW

:-50.0

HIGH

:-50.0

HIGH

:50.0

HIGH

:50.0

AUTO

ST1

:0.0

ST1

:0.0

ST1

:-50.0

ST2

:-50.0

ST2

:50.0

ST2

:500

ST2

:50.0

SET

:-25.0

SET

:25.0

SET

:250

SET

:0.0

●Accessory

●Sold separately

● Panel cut-out

. Pressure unit label

(unit:mm)

. Bracket A

. Connector cable(PSO-C01, 2m)

. Panel bracket(PSO-B02/B03)

. M5 Gender(PSO-Z01)

. Front cover(PSO-P01)

Dimensions

The tightening torque of

one touch fitting should be

max. 10N.m. It may cause

machanical problems.

Caution

12mm

Spanner

Protection

cover

(PSO-P01)

Mountingpanel

(panelthickness0.8to3.5mm)

Panelbracket

(PSO-B02)

Body

(PSAN)

flashing

in turn

flashing

in turn

flashing

in turn

HighPeakvalue

Low Peak value

Referencepressure

for Auto Shift

hPEK 10)6

lPEK -@7

ShIN 5)0

RUN mode

※1

Press key over3sec.

Springwasher

Hexagonwrench

bolt(M3×6)

BracketA

BracketB

※A

2-M3Tap

30.7

22.8 7.9

※

30.7

22.8 7.9 8

PT1/8"

Inside

M5Tap

64.2

3-Ø3.2

Ø4.2

12.7

. Bracket B

3-Ø3.2

4.2

Ø4.2

PT1/8"model

(standard)

NPT1/8"model

(panelthickness:0.8to3.5mm)

36+0.5

0

36+0.5

0

10 1

5.7

30 320

25.8

28.2

Unit Descriptions

1. Range of rating pressure:ItispossibletochangethepressureunitinPressure

sensor.Pleaseusedifferentunitaslabelforyourapplication.

2. 4digit LED display(Red):Usedtoindicatemeasuredpressurevalue,setting

valueanderrormessage.

3. Output1 indicator(Red):Output1isON,LEDwillbeON.

4. Output2 indicator(Green):Output2isON,LEDwillbeON.

5. key:UsedtoenterintoPreset/ParametersettingmodeandtosaveSetting

mode.

6. , key:Usedtosetparameterandpreset,peakvaluecheckmode,function

settingoroutputoperationmode.

+ key:Usedforzeropointadjustmentfunctionbypressing + keys

over1sec.simultaneouslyinRUNmode.

Load

(Brown)+V

(Black)OUT1

(White)OUT2

12-24VDC

※ :Forvoltageoutputtypeonly.

1kΩ

Main circuit

(Blue)0V

(Orange)

Analogoutput

voltage/current

Over current

protection

circuit

Over current

protection

circuit

Load

(Brown)+V

(Blue)0V

(Black)OUT1

(White)OUT2

(Orange)Hold/

Autoshiftinput

12-24VDC

Main circuit

Over current

protection

circuit

Over current

protection

circuit

Load

(Brown)+V

(Blue)0V

(Black)OUT1

(White)OUT2

(Orange)Hold/

Autoshiftinput

12-24VDC

Main circuit

Over current

protection

circuit

Over current

protection

circuit

1. Use the unit within the rated specications.

 Failuretofollowthisinstructionmayresultinreorproductdamage.

2. Use dry cloth to clean the unit, and do not use water or organic solvent.

Failuretofollowthisinstructionmayresultinre.

3. This product is designed to detect the pressure of noncorrosive gas. Do not use for corrosive gas.

 Failuretofollowthisinstructionmayresultinproductdamage.

4. Do not use the unit in the place where ammable/explosive/corrosive gas, humidity, direct sunlight,

radiant heat, vibration, impact, or salinity may be present.

Failuretofollowthisinstructionmayresultinreorexplosion.

5. Keep metal chip, dust, and wire residue from owing into the unit.

Failuretofollowthisinstructionmayresultinreorproductdamage.

※The above specications are subject to change and some models may be discontinued without notice.

※Be sure to follow cautions written in the instruction manual and the technical descriptions

(catalog, homepage).

※Ifshort-circuitthecontroloutputterminalorsupplycurrentovertheratedspecification,normalcontrol

signalisnotoutputduetotheoutputshortovercurrentprotectioncircuit

6.Donotpullthecablewithatensilestrengthof30Norover.

Cautions during Use

1.Followinstructionsin'CautionsduringUse'.

 Otherwise,Itmaycauseunexpectedaccidents.

2.12-24VDCpowersupplyshouldbeinsulatedandlimitedvoltage/currentorClass2,SELVpowersupplydevice.

3.Usetheproduct,3secaftersupplyingpower.

4.Whenusingswitchingmodepowersupply,frameground(F.G.)terminalofpowersupplyshouldbegrounded.

5.Wireasshortaspossibleandkeepawayfromhighvoltagelinesorpowerlines,topreventinductivenoise.

6.Thisunitmaybeusedinthefollowingenvironments.

①

Indoors(intheenvironmentconditionratedin'Specications')

②

Altitudemax.2,000m

③

Pollutiondegree3

④

Installation category II

Photoelectric Sensors TemperatureControllers

FiberOpticSensors Temperature/HumidityTransducers

Door Sensors SSRs/PowerControllers

DoorSideSensors Counters

Area Sensors Timers

Proximity Sensors Panel Meters

Pressure Sensors Tachometer/Pulse(Rate)Meters

RotaryEncoders DisplayUnits

Connector/Sockets Sensor Controllers

SwitchingModePowerSupplies

ControlSwitches/Lamps/Buzzers

I/OTerminalBlocks&Cables

StepperMotors/Drivers/MotionControllers

Graphic/LogicPanels

FieldNetworkDevices

LaserMarkingSystem(Fiber,CO₂,Nd:YAG)

LaserWelding/CuttingSystem

http://www.autonics.com

HEADQUARTERS:

18,Bansong-ro513beon-gil,Haeundae-gu,Busan,

SouthKorea,48002

TEL:82-51-519-3232

E-mail:[email protected]

DR W171185A A

DR W17118 5A A

Autonics PSAN-01CA Series User manual

Related papers

Other documents