schmersal CSS 12-34-V-SD-M-ST Operating instructions

Brand: schmersal

Model: CSS 12-34-V-SD-M-ST

Category: Gateways/controllers

Type: Operating instructions

CSS 34

Operating instructions

Safety relay module

1. About this document

1.1 Function

This operating instructions manual provides all the information you

need for the mounting, set-up and commissioning to ensure the safe

operation and disassembly of the safety switchgear. The operating

instructions must be available in a legible condition and a complete

version in the vicinity of the device.

1.2 Target group: authorised qualified personnel

All operations described in this operating instructions manual must

be carried out by trained specialist personnel, authorised by the plant

operator only.

Please make sure that you have read and understood these operating

instructions and that you know all applicable legislations regarding

occupational safety and accident prevention prior to installation and

putting the component into operation.

The machine builder must carefully select the harmonised standards

to be complied with as well as other technical specifications for the

selection, mounting and integration of the components.

1.3 Explanation of the symbols used

Information, hint, note:

This symbol is used for identifying useful additional

information.

Caution: Failure to comply with this warning notice could

lead to failures or malfunctions.

Warning: Failure to comply with this warning notice could

lead to physical injury and/or damage to the machine.

1.4 Appropriate use

The products described in these operating instructions are developed to

execute safety-related functions as part of an entire plant or machine. It

is the responsibility of the manufacturer of a machine or plant to ensure

the correct functionality of the entire machine or plant.

The safety switchgear must be exclusively used in accordance with

the versions listed below or for the applications authorised by the

manufacturer. Detailed information regarding the range of applications

can be found in the chapter "Product description".

1.5 General safety instructions

The user must observe the safety instructions in this operating

instructions manual, the country specific installation standards as well

as all prevailing safety regulations and accident prevention rules.

Further technical information can be found in the Schmersal

catalogues or in the online catalogue on the Internet:

www.schmersal.net.

Content

1 About this document

1.1 Function ..............................................1

1.2 Target group: authorised qualied personnel..................1

1.3 Explanation of the symbols used ...........................1

1.4 Appropriate use ........................................1

1.5 General safety instructions ...............................1

1.6 Warning about misuse ...................................2

1.7 Exclusion of liability .....................................2

2 Product description

2.1 Ordering code .........................................2

2.2 Special versions........................................2

2.3 Comprehensive quality insurance to 2006/42/EC ..............2

2.4 Purpose ..............................................2

2.5 Technical data .........................................2

2.6 Safety classication .....................................3

3 Mounting

3.1 General mounting instructions .............................3

3.2 Dimensions ...........................................4

3.3 Actuating positions of the safety sensor with regard to the actuator 4

3.4 Switch distance ........................................4

3.5 Adjustment............................................5

4 Electrical connection

4.1 General information for electrical connection..................5

4.2 Series-wiring ..........................................5

5 Diagnostic functions

5.1 Operating principle of the diagnostic LEDs ...................6

5.2 Operating principle of the electronic diagnostic output ..........6

5.3 Safety-sensors with serial diagnostic function .................7

6 Set-up and maintenance

6.1 Functional testing.......................................8

6.2 Maintenance ..........................................8

7 Disassembly and disposal

7.1 Disassembly...........................................8

7.2 Disposal ..............................................8

8 Appendix

8.1 Wiring examples .......................................8

8.2 Wiring conguration and connector accessories ...............9

9 EU Declaration of conformity

x.000 / 01.2020 / v.A. - 101185245-EN / I / 2020-01-10 / AE-Nr. 11847

Operating instructions. . . . . . . . . . . .pages 1 to 10

Original

Operating instructions

Safety sensor

CSS 34

The information contained in this operating instructions manual is

provided without liability and is subject to technical modifications.

There are no residual risks, provided that the safety instructions as well

as the instructions regarding mounting, commissioning, operation and

maintenance are observed.

1.6 Warning about misuse

In case of improper use or manipulation of the safety

switchgear, personal hazards or damages to machinery

or plant components cannot be excluded. The relevant

requirements of the standard ISO 14119 must be observed.

1.7 Exclusion of liability

We shall accept no liability for damages and malfunctions resulting from

defective mounting or failure to comply with this operating instructions

manual. The manufacturer shall accept no liability for damages

resulting from the use of unauthorised spare parts or accessories.

For safety reasons, invasive work on the device as well as arbitrary

repairs, conversions and modifications to the device are strictly

forbidden; the manufacturer shall accept no liability for damages

resulting from such invasive work, arbitrary repairs, conversions and/or

modifications to the device.

2. Product description

2.1 Ordering code

This operating instructions manual applies to the following types:

CSS-

➀

-34

➁

➂

-M-

➃

No. Option Description

➀

Switching distance S

(mm)

Actuation from top

Actuation from side

➁

S lateral active surface

V frontal active surface

➂

D With diagnostic output

SD With serial diagnostic function

➃

L with connecting cable

ST with integrated connector

Only if the information described in this operating instructions

manual are realised correctly, the safety function and

therefore the compliance with the Machinery Directive is

maintained.

2.2 Special versions

For special versions, which are not listed in the order code below 2.1,

these specifications apply accordingly, provided that they correspond to

the standard version.

2.3 Comprehensive quality insurance to 2006/42/EC

Schmersal is a certified company to appendix X of the Machinery

Directive. As a result, Schmersal is entitled to autonomously conduct

the conformity assessment procedure for the products listed in

Appendix IV of the MD without involving a notified body. The prototype

test certificates are available upon request or can be downloaded from

the Internet at www.schmersal.com.

2.4 Purpose

This non-contact, electronic safety sensor is designed for application in

safety circuits and is used for monitoring the position of movable safety

guards. In this application, the safety sensor monitors the position of

hinged, sliding or removable safety guards by means of the coded

electronic CST 34 or CST 180 actuators (refer to table "Actuators and

switching distances").

The safety function consists of safely switching off the safety outputs

when the safety guard is opened and maintaining the safe switched off

condition of the safety outputs for as long as the safety guard is open.

The safety switchgears are classified according to

ISO 14119 as type 4 switching devices.

The diagnostic output of the CSS 34 safety sensor alternatively can be

used as conventional output or as “serial output“ with input and output

channel.

Series-wiring

Series-wiring can be set up. Response and risk times remain

unchanged by series-wiring. The number of components is only limited

by the external cable protection according to the technical data and

the line loss. Series-wiring of up to 31 CSS 34 … SD components with

serial diagnostics is possible.In devices with the serial diagnostics

function (ordering suffix -SD), the serial diagnostics connections

are wired in series and connected to a SD Gateway for evaluation

purposes.

Wiring examples for series-wiring, refer to appendix.

The user must evaluate and design the safety chain in

accordance with the relevant standards and the required

safety level.

If multiple safety sensors are involved in the same safety

function, the PFH values of the individual components must

be added.

The entire concept of the control system, in which the safety

component is integrated, must be validated to the relevant

standards.

2.5 Technical data

Standards: IEC 60947-5-3, ISO 13849-1,

IEC 61508, IEC 62061

Enclosure: glass-fibre reinforced thermoplastic

Operating principle: inductive

Coding level according to ISO 14119: low

Actuator and switch distances

(according to IEC 60947-5-3): see table "Actuator / Switch distances“

Hysteresis: max: 1.5 mm

Repeat accuracy R: < 0.5 mm

Maximum switching frequency: 3 Hz

Series-wiring: Unlimited number of components,

please observe external cable protection,

max. 31 components in case of serial diagnostics

Cable length: max. 200 m (cable length and cable section alter the

voltage drop depending on the output current)

Connector: M12, 8-pin in casing

Pre-wired cable: Y-UL 2517 / 8 × AWG 22 / 8 × 0.35 mm², 2 m

Temperature resistance of the cable:

- at rest: −30 °C … +105 °C

- in motion: −10 °C … +105 °C

Ambient conditions:

Ambient temperature T

: –25 °C to +70 °C

with output current ≤ 0.1 A / Output

–25 °to +65 °C

with output current ≤ 0.25 A / Output

Storage and transport temperature: –25 °C … +85 ºC

Resistance to vibration: 10 … 55 Hz, amplitude 1 mm

Resistance to shock: 30 g / 11 ms

Protection class: IP65, IP67 to IEC 60529

CSS 34

Operating instructions

Safety sensor

Electrical data:

Rated operating voltage U

: 24 VDC −15% / +10%

(stabilised PELV to IEC 60204-1)

Rated operating current I

: 0.6 A

Required rated short-circuit current: 100 A

Fuse (line protection): note the wire

diameter of continuing wire:

- for wire variants: up to 45 °C ambient temperature: 4.0 A

up to 60 °C ambient temperature: 3,15 A

up to 65 °C ambient temperature: 2,5 A

up to 70 °C ambient temperature: 2,0 A

- for plug version: 2.0 A

Rated insulation voltage U

: 32 VDC

Rated impulse withstand voltage U

imp

: 800 V

No-load current I

: 0.1 A

Response time: < 30 ms

Duration of risk: < 60 ms

Protection class: II

Overvoltage category: III

Degree of pollution: 3

EMC rating: according to IEC 60947-5-3

Electromagnetic interference: according to IEC 60947-5-3

Safety inputs X1/X2:

Accepted test pulse duration on input signal: ≤ 1.0 ms

- With test pulse interval of: ≥ 100 ms

Classification: ZVEI CB24I

Sink: C1 Source: C1 C2 C3

Safety outputs Y1/Y2: normally open function, 2 channel,

p-type, short-circuit proof

Rated operating voltage U

1: max. 1 V under U

Leakage current I

: < 0.5 mA

Rated operating current I

: max. 0.25 A, dependent

on ambient temperature

Utilisation category: DC-12, DC-13

Rated operating voltage/current U

: 24 VDC / 0.25 A

Test pulse duration: ≤ 1.0 ms

Test pulse interval: 1,000 ms

Classification: ZVEI CB24I

Source: C1 Sink: C1

Diagnostic output: short-circuit proof, p-type

Voltage drop: < 5 V

Rated operating voltage U

: min. (U

– 5 V)

Operating current I

: max. 0,05 A

Utilisation category: DC-12, DC-13

Rated operating voltage/current U

: 24 VDC / 0.05 A

Wiring capacitance for serial diagnostics: max. 50 nF

2.6 Safety classification

Standards: ISO 13849-1, IEC 61508, IEC 62061

PL: e

Control Category: 4

PFH value: 3.6 x 10

-9

/ h

SIL: suitable for SIL 3 applications

Mission time: 20 years

3. Mounting

3.1 General mounting instructions

Please observe the relevant requirements of the standards

ISO 12100, ISO 14119 and ISO 14120.

The component can be mounted in any position. The active surface

of the safety sensor and the actuator has to be opposite. The sensor

enclosure must not be used as an end stop. The active surface of the

safety sensor is either the lateral surface marked with the type plate or

the front, rounded surface. The safety sensor must only be used within

the assured switching distances ≤ s

and ≥ s

The safety sensor and the CST 34-.-1 or CST 34-S-2 actuators are

supplied with integrated mounting plate. With the slotted holes of the

mounting plates, possible tolerances can be horizontally and vertically

compensated. The components are fitted with M4 screws.

The safety sensors and the actuators can be clipped onto the mounting

plate with different actuating directions. Both components are fixed by

means of a locking cap.

The actuator must be permanently fitted to the safety guards

and protected against displacement by suitable measures

(tamperproof screws, gluing, drilling of the screw heads).

The mounting plates must be pinned after their fixation.

The mounting brackets also must be secured by means of

the supplied locking pin to protect them against tampering.

The CST-S-3 and CST 180 actuators must be protected by

tamper-proof screws or a tamper-proof fitting.

At an ambient temperature of over 55°C, the safety sensor

must be fitted so that it is protected against unintentional

contact with persons.

To avoid any interference inherent to this kind of system and any

reduction of the switching distances, please observe the following

guidelines:

Minimum distance between two sensors: 100 mm

Operating instructions

Safety sensor

CSS 34

3.2 Dimensions

All measurements in mm.

Safety sensor size

97,2

108,2

M12x1

Dimensions Actuator

2735

97,2

101,7

Alternative suitable actuators with different design: refer

to www.schmersal.net.

Integrated mounting plate

101,7

42,5

4,5

R4,6

R2,1

¤5

Holes to be pinned Hole for the pin

3.3 Actuating positions of the safety sensor with regard to the

actuator

Lateral actuation Actuation from front

CST 34-S-1

CSS ..-34-S

CST 34-V-1

CSS ..-34-V

CST 34-S-3

CSS ..-34-S

CSS ..-34-V

CST 34-S-3

CST 34-S-2

CSS ..-34-S

CSS ..-34-V

CST 34-S-2

CST 180-1/-2

CSS ..-34-S

CSS ..-34-V CST 180-1/-2

3.4 Switch distance

Actuators and switching distances (to EN 60947-5-3)

Actuator Sensor CSS ..-34-S

(Actuation from side)

CSS ..-34-V

(Actuation from front)

CST 34-V-1 s

10 mm

8 mm

13 mm

12 mm

10 mm

15 mm

CST 34-S-1

CST 34-S-3

14 mm

12 mm

17 mm

15 mm

13 mm

18 mm

CST 34-S-2

(increased

misalignment)

14 mm

12 mm

17 mm

10 mm

8 mm

16 mm

CST 180-1

CST 180-2

10 mm

8 mm

13 mm

12 mm

10 mm

16 mm

Key

Rated operating distance

Assured switching distance

Assured switch-off distance

Maximum misalignment from side

CSS 34

Operating instructions

Safety sensor

Actuation from side

The side allows for a maximum height misalignment (X) of sensor

and actuator of 36 mm (e.g. mounting tolerance or due to guard door

sagging). Increased misalignment, max. 53 mm, possible when the

CST 34-S-2 actuator is used. The axial misalignment (Y) is max. ± 10

mm.

Maximum misalignment from front

Actuation from front

The front face allows for an axial misalignment

(Z) of max. ± 8 mm.

3.5 Adjustment

The distance between the sensor and the actuator must be set to < S

If variations in the clearance between the sensor and the actuator is

detected (e.g. sagging of a safety guard), this distance must be reduced

by 4 mm. The yellow LEDs and the diagnostic output indicate the

different ranges.

Recommended Adjustment

Align the safety sensor and actuator at a distance of 0.5 x s

The correct functionality of both safety channels must be checked by

means of the connected safety-monitoring module.

4. Electrical connection

4.1 General information for electrical connection

The electrical connection may only be carried out by

authorised personnel in a de-energised condition.

The power supply for the safety sensors must provide protection

against permanent over-voltage. Under fault conditions, the voltage

must not exceed 60 V. supply units according to IEC 60204-1 is

recommended.

The safety outputs can be integrated into the safety circuit of the control

system. For applications of PL e / control category 4 to ISO 13849-1,

the safety outputs of the safety sensor or sensor of the chain must be

wired to a safety monitoring module of the same control category .

Requirements for the connected safety-monitoring module

• Dual-channel safety input, suitable for p-type safety sensors with NO

function.

• Digital inputs to EN 61131-2, Table "Standard operating ranges for

digital inputs (current sinking)"

The safety sensors cyclically switch off the output to test them. The

switch-off times of max. 500 μs must be tolerated by the evaluating

device. Short-circuit recognition by the evaluation is not necessary.

Note on the total length of a safety sensor chain, refer to paragraph

"Series-wiring". The maximum load current of 250 mA per safety

channel must be observed. Contactors with higher load currents must

be controlled by intermediate control relays.

Information for the selection of suitable safety-monitoring

modules can be found in the Schmersal catalogues or in the

online catalogue on the Internet: www.schmersal.net.

The self-monitoring safety sensors of the CSS 34F0 or CSS 34F1

series can replace the safety-monitoring module. Therefore, they can

only be used as the first sensor of a series-wired sensor chain. (refer to

operating instructions CSS 34F0 / CSS 34F1).

If the safety sensor is connected to electronic safety-

monitoring modules, we recommend that you set a

discrepancy time of 100 ms. The safety inputs of the safety-

monitoring module must be able blanking a test impulse of

approx. 1 ms. The safety-monitoring module does not need to

have a cross-wire short monitoring function, if necessary, the

cross-wire short monitoring function must be disabled.

4.2 Series-wiring

Series-wiring can be set up. The number of devices is limited for safety

reasons. Series-wiring of CSS 34-…-SD with serial diagnostics is

possible for up to 31 devices. A 200 m long sensor chain can be set up.

Please note that voltage losses could occur (due to cable length, cable

section, voltage drop/sensor)! For longer cable lengths, the section of

the connecting cables must be taken as large as possible.

Wiring examples for series-wiring, refer to appendix.

Protection is not required when pilot wires are laid. The cables however

must be separated from the supply and energy cables. The max. fuse

rate for a sensor chain depends on the section of the connecting cable

of the sensor.

Cable design in case of serial diagnostics

The wiring capacitance of the connecting cable of the safety sensor

must not exceed 50 nF.

Depending on the strand structure, normal unshielded 30 m long control

cables LIYY 0.25 mm

to 1.5 mm

have a wiring capacitance of approx.

3 … 7 nF.

When wiring SD devices, please observe the voltage drop

on the cables and the current carrying capacity of the

individual components.

Accessories for the series-wiring

For convenient wiring and series-wiring of SD components,

the SD junction boxes PFB-SD-4M12-SD (variant for the

field) and PDM-SD-4CC-SD (variant for control cabinet on

carrier rail) are available along with additional comprehensive

accessories. Detailed information is available on the Internet,

www.schmersal.net.

Operating instructions

Safety sensor

CSS 34

5. Diagnostic functions

5.1 Operating principle of the diagnostic LEDs

The safety sensor indicates the operating condition and faults by means

of three-colour LEDs located in the lateral surfaces of the sensor.

The following LED indicators are the same for safety sensors

with conventional diagnostic output as for those with a serial

diagnostic function.

The green LED indicates that the safety sensor is ready for operation.

The sensor is not actuated.

The yellow LED indicates the switching condition of the safety outputs.

The flashing can be used to prematurely detect variations in the

clearance between the sensor and the actuator (e.g. sagging of a safety

guard). The sensor must be adjusted before the distance to the actuator

increases and before the safety outputs are disabled, thus stopping the

machine. If an error is detected, the red LED will be activated.

Flash codes red diagnostic LED

LED indication (red) Error cause

1 flash pulse Error output Y1

2 flash pulses Error output Y2

3 flash pulses Cross-wire Y1/Y2

4 flash pulses ambient temperature too high

5 flash pulses Wrong or defective actuator

Continuous red Internal error

5.2 Operating principle of the electronic diagnostic output

Table 1: Examples of the diagnostic function of the safety-sensor with conventional diagnostic output

Sensor function LED

green red yellow

Diagnostic

output

Safety outputs

Y1, Y2

Note

I. Supply voltage On Off Off 0 V 0 V Voltage on, no evaluation of the voltage quality

II. actuated On Off On 24 V 24 V The yellow LED always signals the presence of an actuator

within range

III. Actuated, actuator

in limit area

On Off Flashes

(1Hz)

24 V pulsed 24 V The sensor must be adjusted before the distance to the

actuator increases and before the safety outputs are disabled,

thus stopping the machine

IV. Error warning,

sensor actuated

On Flashes On 0 V 24 V After 30 minutes if the error is not rectified

V. Error On Flashes On 0 V 0 V Refer to table with flash codes

The short-circuit proof diagnostic output can be used for central

visualisation or control functions, e.g. in a PLC.

The electronic diagnostic output signals faults before the safety outputs

are disabled, thus enabling a controlled shutdown.

The diagnostic output is not a safety-relevant output!

The closed condition of the safety guard, i.e. the sensor is actuated,

is indicated through a positive signal. If the sensor is operating near

the limit of its switching distance, e.g. due to the sagging of the safety

guard, the sensor will emit a 1 Hz cyclic signal before the safety outputs

are disabled.

The diagnostic output can also be used to detect clearance variations

between the sensor and the actuator in the same way as the yellow

LED.

An active fault causes the diagnostic output to be disabled. The safety

outputs are disabled after max. 30 minutes if the fault is not rectified.

The signal combination, diagnostic output disabled and safety channels

still enabled, can be used to stop the production process in a controlled

manner.

Error

Any error that does not immediately affect the functionality of the safety

sensor (e.g. the ambient temperature being too high, interference

potential at a safety output, cross-wire short) will lead to a delayed

shut-down.

After fault rectification, the error message is reset by opening and re-

closing the corresponding safety guard. The safety outputs enable and

allow a restart.

Error warning

The safety outputs are disabled after 30 minutes if the error is not

rectified. The signal combination, diagnostic output disabled and

safety channels still enabled, can be used to stop the production

process in a controlled manner.

CSS 34

Operating instructions

Safety sensor

5.3 Safety-sensors with serial diagnostic function

Safety sensors with serial diagnostic cable have a serial input and

output cable instead of the conventional diagnostic output. If CSS

sensors are daisy-chained, the diagnostic data are transmitted through

the series-wiring of the inputs and outputs.

Max. 31 sensors can be wired in series. For the evaluation of the serial

diagnostics line either the PROFIBUS-Gateway SD-I-DP-V0-2 or the

Universal-Gateway SD-I-U-… are used. This serial diagnostic interface

is integrated as a slave in an existing field bus system. In this way, the

diagnostic signals can be evaluated by means of a PLC. The necessary

software for the integration of the SD-Gateway is available for download

at www.schmersal.net.

Detailed information about the use of the serial diagnostics

can be found in the operating instructions of the PROFIBUS-

Gateway SD-I-DP-V0-2 and the Universal-Gateway SD-I-U-….

Accessories SD interface

For ease of wiring and series-wiring of SD devices,

considerable accessories are available. Detailed information

is available on the Internet, www.schmersal.net.

The response data and the diagnostic data are automatically and

permanently written in the assigned input byte of the PLC for each

safety sensor in the series-wired chain. The request data for each

safety sensor are transmitted to the device through an output byte of

the PLC.

In the event of a communication error between the field bus Gateway

and the safety sensor, the switching condition of the safety output of the

safety sensor is maintained.

The following operational information is automatically and permanently

written in an input byte of the PLC for each CSS 34 sensor of the

series-wired chain

Bit 0: safety outputs enabled

Bit 1: safety sensor actuated, actuator identified

Bit 4: both safety inputs live

Bit 5: safety sensor actuated in hysteresis area

Bit 6: error warning, switch-off delay activated

Bit 7: error, safety outputs switched off

Error

A fault has occured, which causes the safety outputs to be disabled.

The fault is reset, when the cause is eliminated and bit 7 of the request

byte changes from 1 to 0 or the safety guard is opened. Faults at

the safety outputs are only deleted upon the next release, as the

fault rectification cannot be detected sooner. For devices with serial

diagnostic, a bit can be set/deleted in the call telegram to reset the fault.

For devices with serial diagnostic, a bit can be set/deleted in the call

telegram to reset the fault.

Error warning

A fault has occurred, which causes the safety outputs to be disabled

after 30 minutes. The safety outputs initially remain enabled. This

enables the shutdown of the process in a controlled manner. An error

warning is deleted when the cause of error is eliminated.

Diagnostic error (warning)

If an error (warning) is signalled in the response byte, detailed fault

information can be read out.

Table 2: Function of the visual diagnostic LEDs, the serial status signals and the safety outputs by means of an example

System condition LED Safety outputs serial diagnostic byte bit no.

green red yellow Y1, Y2 7 6 5 4 3 2 1 0

Supply voltage on, not actuated On Off Off 0 V 0 0 0 0 0 0 0 0

Actuated, safety outputs enabled On Off On 24 V 0 0 0 1 0 0 1 1

Actuated in limit area On Off Flashes

(1Hz)

24 V 0 0 1 1 0 0 1 1

Actuated, warning On On/

flashes

On 24 V 0 1 0 1 0 0 1 1

Actuated, fault On On/

flashes

On 0 V 1 1 0 1 0 1 1 0

The shown bit order of the diagnostic byte is an example. A different combination of the operational conditions will lead to a change of the bit order.

Table 3: I/O data and diagnostic data

Communication directions: Request byte: from the PLC to the local safety sensor

Response byte: from the local safety sensor to the PLC

Warning/error byte: from the local safety sensor to the PLC

Bit n° Request byte Response byte Diagnostic

error warning

Diagnostic

error

Bit 0: Error reset Safety output activated Error output Y1 Error output Y1

Bit 1: --- Actuator detected Error output Y2 Error output Y2

Bit 2: --- --- Cross-wire Y1/Y2 Cross-wire Y1/Y2

Bit 3: --- --- Temperature too high Temperature too high

Bit 4: --- Input condition X1 and X2 --- incorrect or defective actuator

Bit 5: --- Actuated in limit area Internal device error Internal device error

Bit 6: --- Error warning Communication error between the field

bus Gateway and the safety switch

---

Bit 7: Error reset Error (enabling path switched off) Operating voltage too low ---

The described condition is reached, when Bit = 1

Operating instructions

Safety sensor

CSS 34

8. Appendix

8.1 Wiring examples

The application examples shown are suggestions. They however do not release the user from carefully checking whether the switchgear and its set-

up are suitable for the individual application.

Wiring example 1: Series-wiring of the CSS 34 with conventional diagnostic output

The voltage is supplied to both safety inputs of the last safety sensor of the chain (considered from the safety-

monitoring module). The safety outputs of the first safety sensor are wired to the safety-monitoring module.

12356 8

OUT

SPS/PLC

24 VDC

GND

CST 34-S-1

CSS 34

CST 34-S-1

CSS 34

Safety outputs → Evaluation

Wiring example 2: Series-wiring of the CSS 34 with serial diagnostic function

The safety outputs of the first safety sensor are wired to the safety-monitoring module.

The serial Diagnostic Gateway is connected to the serial diagnostic input of the first safety sensor.

Field bus

1235468

SD IN

SD OUT

1235468

SD IN

SD OUT

SD INSD OUT

SD IN

24 VDC

GND

CST 34-S-1

CSS 34

CST 34-S-1

CSS 34

Safety outputs → Evaluation

Gateway

6. Set-up and maintenance

6.1 Functional testing

The safety function of the safety components must be tested. The

following conditions must be previously checked and met:

1. Fitting of the sensor and the actuator

2. Fitting and integrity of the power cable

3. The system is free of dirt and soiling (in particular metal chips)

6.2 Maintenance

In the case of correct installation and adequate use, the safety sensor

features maintenance-free functionality.

A regular visual inspection and functional test, including the following

steps, is recommended:

• Check the fitting of the safety sensor and the actuator

• Remove possible metal chips

• Check the cable for damage.

Measures must be taken to protect against manipulation or

against the bypassing of safety device, for example, using an

extra actuator.

Damaged or defective components must be replaced.

7. Disassembly and disposal

7.1 Disassembly

The safety switchgear must be disassembled in a de-energised

condition only.

7.2 Disposal

The safety switchgear must be disposed of in an appropriate

manner in accordance with the national prescriptions and legislations.

CSS 34

Operating instructions

Safety sensor

8.2 Wiring configuration and connector accessories

Function safety switchgear Pin configuration

of the connector

Colour codes of the Schmersal

connectors

Poss. colour codes of other

customary connectors

or the integrated

cable

with conventional

diagnostic output

with serial

diagnostic function

IP67 / IP69

to DIN 47100

IP69K

(PVC)

IEC 60947-5-2: 2007

A1 U

1 WH BN BN

X1 Safety input 1 2 BN WH WH

A2 GND 3 GN BU BU

Y1 Safety output 1 4 YE BK BK

OUT Diagnostic output SD output 5 GY GY GY

X2 Safety input 2 6 PK VT PK

Y2 Safety output 2 7 BU RD VT

IN without function SD input 8 RD PK OR

Connecting cables with coupling (female)

IP67 / IP69, M12, 8-pole - 8 x 0.23 mm²

to DIN 47100

Connecting cables with coupling (female)

IP69K, M12, 8-pole - 8 x 0.21 mm²

Cable length Part number Cable length Part number

2.5 m

5.0 m

10.0 m

103011415

103007358

103007359

5.0 m

5.0 m, angled

10.0 m

15.0 m

101210560

101210561

103001389

103014823

CSS34-F-EN

Operating instructions

Safety sensor

CSS 34

Place and date of issue: Wuppertal, 13. November 2019

Authorised signature

Philip Schmersal

Managing Director

EU Declaration of conformity

Original K.A. Schmersal GmbH & Co. KG

Möddinghofe 30

42279 Wuppertal

Germany

Internet: www.schmersal.com

We hereby certify that the hereafter described components both in their basic design and construction conform

to the applicable European Directives.

Name of the component: CSS 34

Type: See ordering code

Description of the component: Non-contact safety sensor

Relevant Directives: 2006/42/EC

2014/30/EU

2011/65/EU

Machinery Directive

EMC-Directive

RoHS-Directive

Applied standards: EN 60947-5-3:2013

ISO 14119:2013

EN ISO 13849-1:2015

EN 61508 parts 1-7:2010

EN 62061:2005 + AC:2010 + A1:2013 + A2:2015

Notied body for the prototype test: TÜV Rheinland Industrie Service GmbH

Alboinstraße 56

12103 Berlin

ID n°: 0035

EC- test certicate: 01/205/5194.02/19

Person authorised for the compilation

of the technical documentation:

Oliver Wacker

Möddinghofe 30

42279 Wuppertal

9. EU Declaration of conformity

The currently valid declaration of conformity can be

downloaded from the internet at www.schmersal.net.

K.A. Schmersal GmbH & Co. KG

Möddinghofe 30, 42279 Wuppertal

Germany

Phone: +49 202 6474-0

Telefax: +49 202 6474-100

E-Mail: [email protected]

Internet: www.schmersal.com

schmersal CSS 12-34-V-SD-M-ST Operating instructions

Brand: schmersal

Model: CSS 12-34-V-SD-M-ST

Category: Gateways/controllers

Type: Operating instructions

Download PDF

report

schmersal CSS 12-34-V-SD-M-ST Operating instructions

schmersal CSS 12-34-V-SD-M-ST Operating instructions

Related papers

Other documents