Kohler K-P8300-KSL-NA Dimensions Guide
- Category
- Faucets
- Type
- Dimensions Guide
Features
•
Project Pack: Supplied 12 per case
•
Includes valve body, rough-in guide and test cap
•
1/2" Universal NPT & direct sweat inlets & outlets, with stops
•
Service stops supplied loose (not factory installed in valve body)
- ready for making sweat connections to valve inlets
•
Service stops include integral check valves
•
Requires valve cartridge and trim to complete installation (sold
separately).
Material
•
Forged De-zincification Resistant Brass body provides long
term reliability and resistance to aggressive water conditions
Installation
Codes/Standards
•
Designed for use in standard, back to back and thin wall
installations
ASME A112.18.1/CSA B125.1
•
Valve body features integral mounting locations and symmetrical
valve inlets to simplify installation
KOHLER
®
Faucet Lifetime Limited
Warranty
•
Rough-in guide designed for both standard and thin wall
installations
See website for detailed warranty information.
•
Installed valve rough-in can be flushed and pressure tested to
150psi max (air or water) without cartridge, using K-10351 Test
Cap (supplied)
Required Products/Accessories
K-8305/K-P8305 Series Rite-Temp® Cartridges
or
K-8305/K-P8305 Series Rite-Temp® Cartridges
1-800-4KOHLER (1-800-456-4537)
Kohler Co. reserves the right to make revisions without notice to product specifications.
For the most current Specification Sheet, go to www.kohler.com.
1-31-2019 18:48 - US/CA
Rite-Temp
®
Valve Body Rough-In
K-P8300-KSL
5-7/8" (149 mm)
Inlet Port 1/2"-14 NPT
and 5/8" ID for 1/2"
Nominal Copper Tubing
Cutout for finished walls
less than 3/4" (19 mm)
Cutout for finished walls
greater than 3/4" (19 mm)
Ø 5" (127 mm)
7/8" (22 mm)
Ø 4-1/2"
(114 mm)
Ø 4"
(102 mm)
Cut Line
Cut Line
Ø 1"
(25 mm)
2-15/16"
(75 mm)
2-3/16"
(56 mm)
9/16"
(14 mm)
Outlet Port
Outlet Port
1/2"-14 NPT and 5/8" ID
for 1/2" Nominal
Copper Tubing
3-1/2" (89 mm)
2-3/4"
(70 mm)
1-15/16"
(49 mm)
1-15/16"
(49 mm)
Max Finished Wall
Min Finished Wall
Notes
Technical Information
Install this product according to the installation
instructions.
All product dimensions are nominal.
Avoid cross-flow conditions. Do not install shut-off
device on either valve outlet.
Cap the shower outlet if deck-mount spout,
diverter, or handshower is connected to the spout
outlet.
Install straight pipe or tube drop of 7" (178 mm)
to 18" (457 mm) with single elbow between the
valve and wall-mount spout.
For finished walls greater than 3/4" (19 mm) and
less than 1-1/2" (38 mm), install support(s) 2" (51
mm) from the stud face.
For finished walls greater than 1-1/2" (38 mm),
install support(s) 3" (76 mm) from the face of the
finished wall.
1-800-4KOHLER (1-800-456-4537)
Kohler Co. reserves the right to make revisions without notice to product specifications.
For the most current Specification Sheet, go to www.kohler.com.
1-31-2019 18:48 - US/CA
Rite-Temp
®
Valve Body Rough-In
K-P8300-KSL
-
1
-
2
Kohler K-P8300-KSL-NA Dimensions Guide
- Category
- Faucets
- Type
- Dimensions Guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Kohler K-8300-KSL-NA Dimensions Guide
-
-
-
-
-
Kohler K-8304-KS-NA Specification
-
Kohler K-8304-PX-NA Dimensions Guide
-
-
-
