Fujitsu UTG-BKXA-W Installation guide

Fujitsu
Brand
Fujitsu
Model
UTG-BKXA-W
Type
Installation guide

Fujitsu UTG-BKXA-W is a panel spacer used for adjusting the position of the indoor unit of a cassette type air conditioner. It can be used to adjust the height of the indoor unit's installation, ensuring that there is no gap between the ceiling and the panel spacer around the entire periphery and no gap between the decoration panel and the main indoor unit. The panel spacer is easy to install, with the following steps:

  1. Assemble the panel spacer.
  2. Secure the panel spacer to the cassette grille.
  3. Install the cassette grille and panel spacer to the indoor unit.

Fujitsu UTG-BKXA-W is a panel spacer used for adjusting the position of the indoor unit of a cassette type air conditioner. It can be used to adjust the height of the indoor unit's installation, ensuring that there is no gap between the ceiling and the panel spacer around the entire periphery and no gap between the decoration panel and the main indoor unit. The panel spacer is easy to install, with the following steps:

  1. Assemble the panel spacer.
  2. Secure the panel spacer to the cassette grille.
  3. Install the cassette grille and panel spacer to the indoor unit.
PREPARATION BEFORE
INSTALLATION
4
INSTALLING THE PANEL SPACER
AIR CONDITIONER
OPTIONAL PARTS
PANEL SPACER
INSTALLATION MANUAL
PART No. 9378876040
For authorized service personnel only.
WARNING
CAUTION
PARTS AND ACCESSORIES
The following installation parts are furnished. Check
them before starting installation work.
Name and Shape
Screw
(short)
Panel spacer
holder
Q'ty
8
8
Name and Shape
Panel spacer
Q'ty
4
1
INSTALLING CASSETTE GRILLE AND
PANEL SPACER TO INDOOR UNIT
CAUTION
Install so that there is no gap between the decora-
tion panel and the main indoor unit.
1
2
3
1
Align the stamped marks on the decoration panel a-
gainst the pipe and the drain of the indoor unit.
2
3
Condensation
Air leakage
Dirty ceiling
Condensation, dew drops
•
Tighten the 4 Hexagon screws.
When there is a gap between the ceiling and
the decoration panel even when the screw is
tightened, readjust the height of the main
indoor unit.
As long as it does not affect the levelness of
the main indoor unit and the drain piping, you
may adjust the height of the main indoor unit
from the hole at the corner of the decoration
panel, with the decoration panel still attached
to the main indoor unit.
(1)Assemble the Panel spacer
(2)
Secure the Panel spacer to the Cassette grille
•
Install 8 Panel spacer holders.
•
Tighten the screws at 8 positions.
199 (7-13/16)
241 (9-1/2)
1
32
Indoor unit Unit:mm (in.)
45 to 47
(1-3/4 to 1-7/8)
Ceiling
Tighten the screw until the seal material between the decoration panel
and the main indoor unit is compressed to a thickness of 5-7mm
(0.197 - 0.276 in.).
Indoor unit
Decoration Panel
Panel spacer
Ceiling
No gap between ceiling
and Panel spacer around entire periphery
(0.197 - 0.276 in.)
5-7 mm
Ceiling
A
Adjust the height of installation for the indoor
unit as shown in the diagram below.
ADJUSTING POSITION OF
INSTALLATION FOR INDOOR UNIT
Panel spacer installation dimension
Completed diagram
A (mm(in.))
UTG-BKXA-W
When installing the Panel spacer, please read this manual
thoroughly.
Before installation, be sure that all sources of power have
been shut off. There is a danger of electric shock.
When installing the Panel spacer, please refer to the
operating manual and installation manual supplied with the
indoor unit.
The Panel spacer is used by assembling it together with a
Cassette type air conditioner.
The Panel spacer cannot be used alone.
Handle Panel spacer carefully. Dropping it on the floor or
subjecting it to strong shock will cause erroneous operation
or accidents.
Hand this manual to the customer to keep for future use,
such as for maintenance or relocation of the air conditioner.
If there is a gap, an error will occur as shown in
the diagram below.
Installation
manual
(This manual)
Use only supplied screws to install the decoration
panel.
For more details, refer to the Cassette grille installa-
tion manual.
Attach the decoration panel temporarily at 2 places
with metal fittings.
For more details, refer to the Indoor unit installation
manual.
Screw(short) x 8
Force:0.8 to 1.2N
.
m
Detail A
(7.1 to 10.6 lbf
.
in.)
Panel spacer
holder
Panel spacer
holder x 8
Hook on
Ensure that there is
no gap between the
hook and the
decoration panel
(4 positions)
No Gap
Hexagon screw x 4
(Decoration panel accessory)
Note: The illustrations in this manual may be different from the
actual product.
Type [Indoor unit height (mm (in.))]
Slim type [246 (9-11/16)]
Standard type [288 (11-5/16)]
•
Be careful when handling the cassette grille.
(1) Do not place the panel facing down, standing
upright or on top of any protruding objects.
(This may cause dents and scratches to the
surface and damage the flap.)
(2) Remove the intake grille on the cassette
grille.
(For details on how to remove, refer to the
installation manual of the cassette grille.)
(3) Place a piece of cardboard on the floor. Then
place the cassette grille on its back onto the
cardboard so as not to scratch the surface of
the panel.
A
  • Page 1 1

Fujitsu UTG-BKXA-W Installation guide

Fujitsu
Brand
Fujitsu
Model
UTG-BKXA-W
Type
Installation guide

Fujitsu UTG-BKXA-W is a panel spacer used for adjusting the position of the indoor unit of a cassette type air conditioner. It can be used to adjust the height of the indoor unit's installation, ensuring that there is no gap between the ceiling and the panel spacer around the entire periphery and no gap between the decoration panel and the main indoor unit. The panel spacer is easy to install, with the following steps:

  1. Assemble the panel spacer.
  2. Secure the panel spacer to the cassette grille.
  3. Install the cassette grille and panel spacer to the indoor unit.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents