Legrand WSP250WCCV4 Installation guide

Brand: Legrand

Model: WSP250WCCV4

Type: Installation guide

This manual is also suitable for

TROUBLESHOOTING

Load will not turn on:

• LEDdoesnotash:

 ‑Checkthesensitivityforproperconguration.

‑Checkallwireconnections.Verifythegroundwireistightlysecured.

• LEDdoesash:

 ‑PresstheON/OFFbutton.Ifloaddoesnotturnon,checkallwire

connectionsandverifytheloadwireistightlysecured.

 ‑Checkthelightleveltrimpot.Turnitfullyclockwise

• Ifloadstilldoesnotturnon,call800.223.4185fortechnicalsupport.

Load will not turn off:

• Thetimedelaycanbesetfor30seconds

(WalkTest),5,10,15,20,25,or30minutes.

Ensurethatthetimedelayissettothe

desireddelayandthatthereisnomovement

withinthesensor’sviewforthattimeperiod.

• Toquicklytesttheunitforproperoperation,

turnthetimedelaytominimum(fully

counterclockwise)andmoveoutofthe

sensor’sview.Loadshouldturnoffafter

30seconds.

• Ifloadstilldoesnotturnoff,call

800.223.4185fortechnicalsupport.

Sensing motion outside desired area:

• Opaqueadhesivetapeisincludedwiththe

sensorandcanbeusedtolimitthedetectionareas.SeeMaskingtheLens.

• Adjustsensitivitycounterclockwisetoreduceexcessivesensitivity.

WSP-250

Passive Infrared Wall Switch

Occupancy Sensor

SPECIFICATIONS

 WSP-250 Voltages.................................................120or277VAC,60Hz

   LoadRequirements

    @120VAC,60Hz............. 0‑800Wballast&tungsten,1/6hp

    @277VAC,60Hz........................................... 0‑1200Wballast

TimeDelayAdjustment...................................30seconds‑30minutes

 SensitivityAdjustment...........................................Minimum‑Maximum

 LightLevelAdjustment..................................................... 10‑200+FC

SENSOR ADJUSTMENT

DO NOT OVERTURN TRIMPOTS WHEN ADJUSTING THE SENSOR!

1. Totestunitoperation,presstheON/OFFbuttontoturntheloadon.

2. Removethebuttoncovertoaccesstheadjustmentcontrols.Useasmall,

atbladescrewdrivertopressdownthelockingtabatthetopofthebutton,

thengentlypryitoff.

a)Setthetimedelaytothe“walktest”position(fullycounterclockwise).

b)Leavetheroom.Theloadshouldgooffafter30seconds.

3. Totestsensitivity:

a) Makenomotionfor3seconds.

b) Waveyourhandsidewaysinfrontofthesensoratadistanceof

approximately12".TheLEDblinkswhenmovementisdetected.

Typically,thesensitivityshouldbeatmaximum(fullyclockwise).

4. Setthelightlevelwhenthecontrolledlightwouldnormallybeturnedoff

duetothepresenceofsufcientdaylightorotherelectriclight.[Ifthis

featureisnotneeded,leavethelightlevelatmaximum(fullyclockwise)].

a) SettheTimeDelaytoatleast5minutes.Thistakesthesensoroutof

Walk‑testmode,andenablesthelightlevelfeature.

b) SettheLightlevelto50%(12o’clockposition)whichisapproximately

100fc.Letthesensortimeoutsolightsareoff.Enterthespaceand

lightsshouldremainoff.

c) Makesureyourbodydoesnotcastashadowonthesensor,andadjust

thelightleveltrimpotclockwiseinsmallincrements.

d) Aftereachadjustment,wait5‑10secondstoseeifthelightsturnon.

Repeatuntilthelightsturnon.Atthissettingtheloadconnectedtothe

sensorwillnotturnoniflightlevelsareabovethecurrentillumination.

Note: Userscanoverridethisfunctionbyplacingtheirhandinfrontofthe

sensortoblockincominglight.Theloadwillthenremainonuntilthe

spaceisunoccupiedorthelightlevelrisesabovethesetpointandthe

timedelayexpires.

5. Resetthetimedelaytothe

desiredsetting.Thetimedelay

canbesetfrom30seconds

(seeWalk‑testfeature,light

levelfeatureisdisabled)

to30minutesin5‑minute

increments.

Call 800.223.4185 for Technical Support

WARRANTY INFORMATION

Pass&Seymour/Legrandwarrantiesitsproductstobefreeofdefects

inmaterialsandworkmanshipforaperiodofve(5)years.Thereare

noobligationsorliabilitiesonthepartofPass&Seymour/Legrandfor

consequentialdamagesarisingoutof,orinconnectionwith,theuseor

performanceofthisproductorotherindirectdamageswithrespecttolossof

property,revenueorprot,orcostofremoval,installationorreinstallation.

Installation Instructions

P.O.Box4822,Syracuse,NY13221‑4822

TechnicalSupport:800.223.4185

www.passandseymour.com

34088611343

Please

Recycle

Visit our website: www.passandseymour.com

Sensitivity (S)

shown as set

for Maximum

Light Level (L)

shown as set

for Maximum (+)

to disable

Time Delay (T)

Shown as set for

15 minutes

Time Delay (T)

Shown as set for

15 minutes

30 seconds

(Walk-test)

5 minutes

10 minutes

20 minutes

25 minutes

30 minutes

WSP250 IS_340886 11343.indd 1-4 3/30/09 9:19:49 AM

UNIT DESCRIPTION AND OPERATION

TheWSP‑250WallSwitchOccupancySensorsturnlightingorfanloadsonand

offbasedonoccupancyandambientlightlevel.Theyaredesignedtoreplacea

standardlightswitch.TheWSP‑250operateswith120or277VAClinevoltage.

Thesensorusespassiveinfraredtechnologytosensehumanmotion,and

definesitasoccupancy.AgreenLEDonthesensorblinksuponoccupancyand

thenresets.Itwillblinkagainwhenitdetectsmotionafterthe2‑secondreset.

Thesensorturnsontheloadautomaticallywhenitdetectsoccupancy.Oncethe

spaceisvacantandthetimedelayelapses,itturnsofftheloadautomatically.

Ifadequateambientlightisalreadypresentinthearea,thesensorwillhold

offtheloaditcontrols.Whenthelightdropsbelowafieldselectableleveland

thesensordetectsoccupancy,thesensorturnsontheload.Onceturnedon,

theloadremainsonuntilthespaceisvacantorthelightlevelrisesabovethe

setpointandthetimedelayexpires.

Manual Operation: TheoccupantcanpresstheON/OFFbuttontoturntheload

onandoff.Whentheloadisturnedofforonmanually,itstaysofforonaslong

asthesensordetectsmotion.Afternomotionisdetectedforthelengthofthe

timedelay,thesensorgoesbacktoautomaticoperation.Iftheloadwason,it

turnsoff.Thenexttimethesensordetectsoccupancyandtheambientlightis

lowerthanthesetlevel,thesensorautomaticallyturnsontheload.

Walk-test feature:

WhentheTimeDelaytrimpot

isinthefullycounterclockwise

position,thesensorhasa30

secondtimedelayandtheLight

Levelfunctionisdisabled.This

allowsyoutoquicklycheckthe

sensorcoveragearea.

Override function:

Intheeventofunitfailureor

ifitisnecessarytoleavethe

loadon,removetheOverride

Jumperplug.Thisdisablesall

automaticonandofffunctions

andtheloadcanonlybe

operatedusingtheON/OFF

button.

COVERAGE PATTERNS

TheWSP‑250detectsmotioninareasupto900sq.ft.andupto35feetfrom

thesensor.Ideally,thesensorisdesignedforsmallamountsofmotionin

spacesupto300sq.ft.TheFresnellensonthesensorisamultiplesegment

viewinglenswithafieldofviewof180°.

Thesensormusthavea

clearviewofthepeoplein

thespaceinordertodetect

occupancy.Obstructions,

suchasfurnitureblocking

thesensor’slens,may

preventoccupancy

detection.

15'

(4.6m)

35'

(10.7m)

4.0'

(1.2m)

35'

(10.7m)

floor

Masking the lens

Opaqueadhesivetapeissuppliedsothat

sectionsofthesensor’sviewcanbemasked.

Thisallowsyoutoeliminatecoveragein

unwantedareas.

Sincemaskingremovesbandsofcoverage,

remembertotakethisintoaccountwhen

troubleshootingcoverageproblems.

1. Connecttheexistingwiresinthewallboxtothesensorflyingleads.

(SeeWiringDirectionsatright).

 • Donotallowbarewiretoshowbelowconnector.

 • Thegroundwiremustbetightly grounded fortheunittooperate

properly.

2. Attachthesensortothewallbymountingitinthewallboxwiththetwo

mountingscrewsprovided.

3. Turnonpoweratthecircuitbreaker.

 There is an initial warm-up period after installation.Itmaytakeuptoa

minutebeforetheloadturnsonduetoasensorwarm‑upperiodduring

initialpower‑up(thisoccursduringinstallationonly).Theloadturnsonafter

thewarm‑upperiodendsifthesensordetectsmotion.

 Rapid successive pressing of the ON/OFF button causes a delay in function.

Asinglepressofthebuttoncausesanimmediateresponse.Ifthebutton

ispressedagainwithin2seconds,theswitchignoresit.Waitatleasttwo

secondsbetweenbuttonpresses.

4. TestthesensorusingtheprocedureintheSensorAdjustmentssection.

5. Replacewallswitchcoverplate.

CAUTION

Turn the power off at the circuit breaker before installing the sensor.

INSTALLATION

Cover plate

WSP-250

Wall Switch

Wall

Junction Box

Load

Red

Black to Line

Green

Neutral

Single-level wiring

WIRING DIRECTIONS

Fornormalinstallationofthe

WSP‑250connect:

1. LOADtoRedflyinglead.

2. LINEtoBlackflyinglead.

3. GROUNDtoGreen.

Call 800.223.4185 for Technical Support Call 800.223.4185 for Technical Support

Manual bi-level lighting wiring

Load

Green

Red

Black to Line

Neutral

Visit our website: www.passandseymour.com Visit our website: www.passandseymour.com

ON/OFF

Switch

Override

Jumper

Light Level

Time Delay

Sensitivity

LED

Fresnel Lens

ON/OFF Button

(Switch Cover)

Press down

on tab and

pry off Cover

(L)

(T)

(S)

Maximum = clockwise

Minimum = counterclockwise

Side View

Top View

Opaque tape

WSP250 IS_340886 11343.indd 5-8 3/30/09 9:19:52 AM

Legrand WSP250WCCV4 Installation guide

Brand: Legrand

Model: WSP250WCCV4

Type: Installation guide

This manual is also suitable for

Download PDF

report

Legrand WSP250WCCV4 Installation guide

This manual is also suitable for

Legrand WSP250WCCV4 Installation guide

Related papers

Other documents