Selecto SP20-2 User manual

Category
Sanitary ware
Type
User manual

This manual is also suitable for

SUPERPLUS
WATER FILTRATION SYSTEM
For Model #: SP20-2, SP40-2
INSTRUCTIONS/ASSEMBLY
USE AND CARE MANUAL
(Important: Read this manual thoroughly before install)
1
© Selecto, Inc.
TABLE OF CONTENTS
General Notes
About Your Product
Installation Procedures for Hard Copper Pipe
Installation Procedures for Rigid Plastic Pipe
Directions to Reverse Water Flow
Cartridge Change-Out Instructions
QR Code Instructions
Troubleshooting & Repair
Limited Warranty
2
3
4
6
8
9
10
11
12
HELP AND SUPPORT
Selecto, Inc.
3980 Lakeeld Court
Suwanee, GA 30024 USA
WWW.SELECTOINC.COM
Product Customer Support Hotline:
Toll Free: 1-800-635-4017
Monday to Friday
8:00 a.m. — 5:00 p.m. EST
2
© Selecto, Inc.
OPTIONAL PARTS LISTPACKAGE CONTENTS
Twin Head Assembled #: 300-778HD
Pressure Gauge #: 300-023FA
Plastic 3/4” Shut-Off Valve #: 300-743
Inlet Fitting 3/4” #: 300-714
Outlet Fitting 3/4” #: 300-720
Pressure Relief Valve #: 300-738
3/4” Plug #: 300-715
Blue Retaining Clip #: 300-708E
Plastic Housing (Comes Assembled)
2 Filtration Cartridges
Spare Parts Kit (2 Lubricant Packs, 4 Clips, 4 O-Rings,
1 Inlet, 1 Outlet)
Instructions/Assembly Use and Care Manual
GENERAL NOTES
WARNING
It is important to ensure that you are in compliance with all applicable state and
local plumbing codes before you start installation of this product. Use of a licensed
technician for installation is recommended. All steps provided throughout are for
the typical installation only.
1) Read and understand all of the instructions before attempting to install and operate this equipment.
Failure to do so may result in injury and damage to person and/or property.
2) Prior to installation, shut off the water.
3) It is important to ensure the mounting to the wall is strong enough to bear the water weight
of the product.
4) Do NOT install system direct to the sunlight or freezing environment.
5) When working with hard copper piping, keep all heat sources at least 18” away from plastic
components. The plastic components can be damaged by heat from the torch which may be used in
the installation.
6) After installation, check all connections for leaks before operating the unit.
7) Refer to the Installation Procedures to ensure that all clips are in the right position before
operating the unit.
THANK YOU FOR PURCHASING OUR PRODUCT
Everyone here at Selecto, Inc. would like to thank you for your support and
continued use of our products. We believe everyone should have access to safe,
clean water. Your purchase is a small step towards a clean future.
3
© Selecto, Inc.
SP20-2 SP40-2
• 400,000 gallon capacity at 15 GPM
• Temperature range between 34° F and 100° F
• Minimum pressure: 40 PSI
• Maximum pressure: 120 PSI
Dimensions:
22” × 9” × 29”
Weight:
With Water: 54 lbs.
Without Water: 28 lbs.
Replacement Filtration Cartridge:
SP20-2RC
• 300,000 gallon capacity at 10 GPM
• Temperature range between 34° F and 100° F
• Minimum pressure: 40 PSI
• Maximum pressure: 120 PSI
Dimensions:
22” × 9” × 23”
Weight:
With Water: 40 lbs.
Without Water: 21 lbs.
Replacement Filtration Cartridge:
SP40-2RC
ABOUT YOUR PRODUCT
4
© Selecto, Inc.
INSTALLATION PROCEDURES
INSTALL FILTER HEAD:
For Hard Copper Pipe Installing (steps 1 to 6 of 11):
A. Filter Head Assembly
1. Center, level, and mount the
lter heads
4. Connect inlet tting onto 3/4”
hard piping
2. Remove blue clip from inlet side
5. Reconnect plastic tting back to
the lter head
B. You can slide the heads out toward either side of
channel to separate backplate for easy installation
3. Pull and separate inlet Shut-Off
valve tting
6. Re-install retaining blue clip
Tap Water
Inlet
Filtered Water
Outlet
5
© Selecto, Inc.
INSTALLATION PROCEDURES (CONTINUED)
For Hard Copper Pipe Installing (steps 7 to 11 of 11):
7. Hand press down the clip and
ush w/head surface
11. Now the installation is complete
8. Repeat steps 2-7 for the outlet
side of piping
9. Install 1st cartridge w/ align
4-tags
10. Install the 2nd cartridge
Tap Water
Inlet
Filtered Water
Outlet
6
© Selecto, Inc.
INSTALLATION PROCEDURES (CONTINUED)
For Rigid Plastic Pipe Installing (steps 1 to 6 of 14):
1. Center, level, and mount the
lter heads
INSTALL FILTER HEAD:
A. Filter Head Assembly B. You can slide the heads out toward either side of
channel to separate backplate for easy installation
4. Connect inlet tting onto 3/4”
hard piping
2. Remove blue clip from inlet side
5. Reconnect plastic tting back to
the lter head
3. Pull and separate inlet Shut-Off
valve tting
6. Re-install retaining blue clip
Tap Water
Inlet
Filtered Water
Outlet
7
© Selecto, Inc.
INSTALLATION PROCEDURES (CONTINUED)
For Rigid Plastic Pipe Installing (steps 7 to 14 of 14):
8. Repeat steps 2-7 for the outlet
side of piping
9. Apply sealant on 3/4” CPVC pipe 10. Reconnect plastic tting/clip
back to the lter head
11. Installed Plastic pipe
7. Hand press down the clip and
ush w/head surface
12. Install 1st cartridge w/align
4-tags
13. Install 2nd cartridge
14. Now the installation is complete
Tap
Water
Inlet
Filtered
Water
Outlet
8
© Selecto, Inc.
DIRECTIONS TO REVERSE WATER FLOW
NOTE: Not recommended, unless necessary
EXCHANGE PROCEDURES
See below diagram. Begin by pulling out the blue clips on either side. Proceed to remove the 4 ttings (two from
each end) and exchange with the opposite end. Properly install all ttings back on the lter head. If using hard
copper piping, use the same technique from pages 4 and 5 (ref. Steps 2-7). If using rigid plastic piping, use the same
technique from pages 6 and 7 (ref. Steps 2-7).
Plug
300-715
Plug
300-715
Filtered Outlet
300-720
Filtered Outlet
300-720
Tap Inlet
300-714
Tap Inlet
300-714
(Reversal of water ow path from right to left completed)
(How to reverse the water ow direction)
Pressure Relief
300-738
Pressure Relief
300-738
9
© Selecto, Inc.
CARTRIDGE CHANGE-OUT INSTRUCTIONS
Normally located at left end of the lter system.
Push until no more water comes out.
The cartridge should be twisted counter-clockwise
in relation to the bottom of the cartridge.
Be sure to properly dispose of the old cartridges (#5 recyclable).
The sanitary cap is located at the top of the new cartridge.
Lubrication is provided in Spare Parts Kit.
Be sure to push cartridge all the way in.
The cartridge should be twisted clockwise
in relation to the bottom of the cartridge.
Hand tight is sufcient for a proper seal.
Cartridges should be changed at least once a year, when the pres-
sure on the gauge has dropped into the red zone (less than 20 psi),
or when bad taste and/or odor return.
1. Shut off inlet valve
2. Push “Red” pressure relief button to relieve pressure
3. Grasp lter cartridge, and twist 1/8 counter-clockwise turn
4. Pull downward about 2” to remove the lter cartridge
5. From the new cartridge, remove and discard the “Red” sanitary cap.
6. Be sure to apply sufcient lubrication to the O-Rings.
7. Align the ear of the cartridge with the notch located
in the lter head. Push upwards to insert.
8. Turn cartridge clockwise until a denite stop is felt
and the cartridge is sealed.
9. Turn on the inlet valve. Flush newly installed lter
cartridges for 3 minutes (from sink faucet).
10
© Selecto, Inc.
QR CODE INSTRUCTIONS
It is recommended to replace cartridges at least once a year, or when
the pressure on the gauge has dropped into the red zone (less than
20 psi), or when bad taste and/or odor return.
Use the QR code to register and receive an email alert when it’s time
to change the ltration cartridges to maximize lter performance.
1. Scan the QR code on lter cartridge label with your smart phone.
2. Follow the instructions on the screen to either register for lter replacement reminders,
or to order replacement lters.
3. You will receive reminders via email to change your lter cartridge.
Get email alerts!
11
© Selecto, Inc.
TROUBLESHOOTING AND REPAIR
All SuperPlus Filtration Systems are fully inspected and pressure tested by factory. IF LEAKS- Note: The inlet shut-off
valve must be turned “OFF” (handle in vertical position), and pressure relieved by pushing the “Red” pressure relief
button before attempting to x any leakage problems.
Leaks at threaded connection points. This type of leak should be repaired by removing the tting and applying
additional Teon tape or thread sealant compound. Do not attempt to repair by tightening the tting more. Over
tightening ttings into plastic parts may cause the plastic to crack. This type of damage is considered abuse and
not covered by the warranty.
1.
2.
3.
4.
5.
Leaks at Junction of Modular Fittings to Filter Head. If leaking persists at the junction points, remove the retainer
clip carefully by inserting a screwdriver or other object into to the hole and gently prying “UP” to remove. Gently
remove the leaking tting by “pulling straight out”. Apply additional lubricant (supplied) to the O-ring and re-
insert the tting by gently “pushing all the way in” until the shoulder on the tting contacts the lter head. Examine
the retaining clip for any cracks from removal and re-insert by “pushing straight down” until it is all the way in. If
retaining clip is cracked or stretched in any way, discard it and use a new one (supplied). If the above procedure
does not cure the leak, repeat the processes above, replacing the O-Ring (supplied).
Leaks Between Cartridge and Filter Head
While looking at the top of the lter system,
grasp the cartridge and turn slightly counter-
clockwise, when viewed from bottom and
then back clockwise, making sure that the
ears on the cartridge are fully engaged into
the lter head. The “blue” locking ears on
the cartridge should be fully visible in the 4
recesses on the “black” lter head.
If leakage persists, check all connecting ttings/O-Rings and replace the damage ttings/O-Rings if damaged or
remove cartridge by following the procedures outlined in the Cartridge Change-Out Instructions on “Cartridge
Change-Out” Page.
Inspect the O-Ring on the top of the
cartridge for damage. Replace with a new
O-Ring (supplied) and lubricate well with
lubricant supplied. Replace the cartridge
by following the procedures outlined in
the Cartridge Change-Out Instructions on
“Cartridge Change-Out” Page.
New O-Ring
Lubricant
Round Locking Tab
12
© Selecto, Inc.
SELECTO SUPERPLUS WHOLE HOUSE FILTRATION SYSTEM
LIMITED WARRANTY
What is Covered:
SELECTO warrants the heads of the Selecto SuperPlus Whole House Filtration System to be free of defects in material
and workmanship. Filtration cartridges are excluded from the warranty.
For how long:
The Plastic Head on the Product carry a ve (5) year limited warranty.
What is not covered:
This Warranty does not apply to defects or damage due to abuse, neglect, misuse, accident, alteration, freezing,
re, other acts of God, or damage not caused by SELECTO. In no event will SELECTO be liable for incidental or
consequential damages from a defective unit or improper installation.
• Check all connections for leaks before operating the unit.
• Check that all clips are in the right position.
• The use of replacement lter cartridges other than Selecto brands voids all warranties.
• Any modular changes or abuse voids warranty.
What Selecto, Inc. will do:
SELECTO’s responsibility under this warranty shall be to replace the product if actually defective, or otherwise in
violation of this Warranty. SELECTO shall at its option, either replace the defective Product with a comparable new
unit at no charge, or to refund the full purchase price. SELECTO’s obligations of repair, replacement, or refund are
conditional upon return of the defective Product to SELECTO. If any Product covered hereby is actually defective
within the terms of this warranty, then SELECTO will bear all reasonable and proper shipping or mailing charges
incurred in the return of the Product as set forth herein. If the Product proves not to be defective within the terms of
this Warranty, then all costs and expenses in connection with processing of the consumers claim hereunder shall be
borne by the consumer.
How to get service:
To receive service under this Warranty, you must contact Selecto, Inc. at 800-635-4017 Ext. 3 or Customer-service@
selectoinc.com within the Warranty Period to describe the problem to a customer service representative who will
verify that the product is under warranty. You will be required to provide a proof of purchase. The customer service
representative will determine the appropriate next step.
If a return of the product is necessary, whether defective or not, it must be pre-approved by SELECTO and
accompanied by a SELECTO pre-approved, valid, return material authorization number (RMA) clearly marked on the
outside of the shipping container. You will receive the RMA number from a SELECTO customer service representative.
All returned goods must be shipped prepaid to SELECTO from point of origin. Returns not shipped prepaid or
missing a RMA number will be refused.
For Products: SP20-2, SP40-2
13
© Selecto, Inc.
SELECTO SUPERPLUS WHOLE HOUSE FILTRATION SYSTEM
LIMITED WARRANTY (CONTINUED)
When you receive your product:
All claims, whether concealed or not, are your responsibility. Any carton damage or shortages should be noted on the
bill of lading at the time of receipt of the shipment, in accordance with I.C.C. Regulations. If the concealed damage or
loss is noted while unpacking the shipment, the carrier should be notied immediately, per I.C.C. Regulations.
SELECTO must be notied, in writing, including a copy of the carriers claim form, of any damage or loss claims with 15
days of receipt. Failure to notify SELECTO releases SELECTO from any liability.
How state law applies:
This warranty gives you specic legal rights, and you may also have other rights, which vary from state to state.
Warranty is valid only in the continental United States.
For Products: SP20-2, SP40-2
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Selecto SP20-2 User manual

Category
Sanitary ware
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI