Mission Elegante e80 User manual

Brand: Mission

Model: Elegante e80

Category: Loudspeakers

Type: User manual

International Audio Group

Huntingdon

PE29 6XU

England

T: +44 (0) 1480 447700

F: +44 (0) 1480 431767

[email protected]

www.mission.co.uk

Cautions & Warranty conditions 2

Introduction to

elegante 3

Room setup 4-5

System setup 6-7

General information 8

Specifications 9

Précautions et conditions de la garantie 10

Présentation de

elegante 11

Configuration de la salle 12-13

Configuration du système 14-15

Renseignements généraux 16

Spécifications 17

Bitte unbedingt beachten & Garantiebedingungen 18

elegante stellt sich vor 19

Zimmereinrichtung 20-21

Systemeinrichtung 22-23

Allgemeine Informationen 24

Technische Daten 25

Precauciones y Condiciones de Garantía 26

Introducción a

elegante 27

Preparación del recinto 28-29

Preparación del sistema 30-31

Información general 32

Datos técnicos 33

English

Deutsch

Español

Français

Cautions

Warranty conditions

The warranty card enclosed should be completed and returned to Mission or

its Distributor within 8 days of purchase.

No Dealer or Distributor may vary the terms of this warranty which is personal

to the original purchaser and is not transferable.

Please retain the sales receipt as proof of purchase.

Warranty claims must wherever possible be made through the Dealer from

whom the equipment was purchased.

This

warranty

excludes:

Damage caused through neglect, accident, misuse, wear and tear, or through

incorrect installation, adjustment or repair by unauthorised personnel.

Any unauthorised servicing will result in loss of warranty.

Liability for damage or loss occurring in transit to or from the purchaser.

Consequent damage, loss or injury, arising from or in conjunction with this

equipment.

Equipment for attention under warranty should be considered return carriage

paid. If equipment is found to comply with the published specification, Mission

reserves the right to raise a charge.

The above conditions do not affect your statutory rights as a consumer.

IMPORTANT SAFETY INSTRUCTIONS

When this symbol is shown there is a risk of electrical

shock.

When this symbol is shown extreme caution should be observed.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPARATUS TO RAIN OR MOISTURE.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

DO NOT use this apparatus near water.

Clean only with dry cloth.

DO NOT install near any heat sources such as radiators, heat registers, stoves,

or other apparatus (including amplifiers) that produce heat.

Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

Unplug this apparatus during lightning storms or when unused for long

periods of time.

Refer all servicing to qualified service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

Install in accordance with the manufacturer’s instructions.

WARNING: If using spikes make sure that they do not pierce mains cable etc.

under /above the carpet.

When making any connections, switch the amplifier off.

When you switch on your system or change sources, set the volume control at

minimum and turn the level up gradually.

DO NOT use your amplifier at full volume.

Avoid extreme settings of tone controls or graphic equalisers. Ideally, they

should be set ‘flat’ or, if possible, bypassed.

DO NOT place heavy objects on top of loudspeaker cabinets.

Ensure that all loudspeakers in the system are correctly wired and are in

phase.

DO NOT connect your loudspeakers to the mains supply, except for

subwoofers.

DO NOT attempt to dismantle the loudspeaker. There are no user serviceable

parts inside and you will render the warranty void.

Site hi-fi electronics away from the loudspeakers on a rigid stand or cabinet.

Loudspeakers should not be placed directly facing other hi-fi units, or share

the same shelf or cabinet.

Site unscreened speakers and subwoofers at least 0.5m away from TV sets,

computers etc. Some manufacturers forbid the placing of objects on top of

their TV sets. Check your TV handbook before installing the centre speaker

directly on your TV set. Consult your TV dealer if you are in any doubt.

Use only attachments / accessories specified by the manufacturer.

DO NOT subject loudspeakers to excessive cold, heat, humidity or sunlight.

DO NOT block any ventilation openings.

DO NOT defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided plug does not fit into

your outlet, consult an electrician for replacement of the obsolete outlet.

The apparatus must not be exposed to dripping or splashing and no objects

filled with liquids, such as vases, should be placed on the apparatus.

Use only with a cart, stand, tripod, bracket or table specified by the

manufacturer, or sold with the apparatus. When a cart is used,

use caution when moving the cart / apparatus combination to

avoid injury from tip-over.

CAUTION:

e8as1, e8as2

The mains power switch for this appliance is located on the rear panel. To

permit free access to this switch the apparatus must be located in an open

area without any obstructions. The mains power plug must remain freely

operable at all times.

CAUTION: Changes or modifications not expressly approved by the

manufacturer could void the user’s authority to operate this device.

IMPORTANT NOTICE TO UK USERS. The subwoofer is supplied with a plug

incorporating a fuse, the value of which is indicated on the pin face of the plug.

Should the fuse or plug need to be replaced refer to the instructions on Page 8.

Introduction to elegante

Thank you for purchasing Mission

loudspeakers. The

elegante series is the

latest in a long line of distinguished Mission

loudspeakers. These technologically

advanced loudspeakers will complement the

finest electronics and decor. Mission

engineers and craftsmen have designed

and manufactured each speaker in the

range to bring you the utmost enjoyment

and listening pleasure over many years of

use.

Please read these instructions carefully

before installing your loudspeakers. A few

minutes studying this manual will ensure

that the superb performance of

elegante

will be fully achieved.

Fitting

spikes

Use floor spikes on the floorstanding

speakers, subwoofer and speaker stands,

for an improvement in clarity of sound. The

spikes can be used with pointed ends

downward on carpets (fig 1), or domed end

downwards on hard floors (fig 2). After

levelling, make sure that the speakers are

stable on their spikes, then tighten all lock

nuts firmly.

Note that where more than four spikes are

provided you may regard the extra spikes as

an aid to stabilisation. Adjust the four main

spikes first and then lower the extra spikes

until they just touch the floor (fig 3).

fig 1

fig 2 fig 3

>0.3 m

1.8 - 2.2 m

fig 2 fig 3 fig 4 fig 5

fig 1

above head height

Room setup

e8c

The e8c loudspeaker is designed to be

placed underneath or above your TV screen

to centre dialogue to the visuals on the

screen. You can place it on a shelf above

the screen, or use the included wall bracket

to fix it to the wall. Alternatively you can

place it on a shelf below the screen and tilt it

upwards to face the listener if required.

shelf

mount

The e8c is supplied fitted to a shelf stand.

You may loosen the fixing screw and rotate

the speaker on the stand to tilt it towards the

head of the seated listener if required.

Tighten the screw once the speaker is in the

optimum position (fig 4).

wall

mount

(fig 5)

Remove the e8c from its stand. Slide the

stand onto the wall bracket and secure it

with the locking screw.

Using the rear plate of the wall bracket as a

template, mark positions on the wall for four

screw fixings. Screw the bracket to the wall

using wall plugs and screws suitable for the

wall construction and the weight of the

loudspeaker.

Make the connections to the terminals on

the rear of the e8c through the elongated

hole provided.

Carefully place the e8c speaker onto the

speaker support arm. Secure the speaker

onto the arm using the fixing screw

provided.

e80 / e81

e80 and e81 speakers are designed to be

used close to rear walls, either on the

included wall brackets or

elegante floor

stands. When used as rear speakers on a

wall the optimum performance for surround

sound will occur when the speakers are

raised above head height (fig 2).

stand

mount

If using the Mission elegante stands, slide

the speaker support arm onto the stand

upright and secure it with the fixing screw.

Carefully place the e80 or e81 speaker onto

the speaker support arm, making sure that

the front extensions of the arm slot into the

recesses in the base of the speaker. Secure

the speaker onto the arm using the fixing

screw provided.

Make the connections to the terminals on

the rear of the speaker, as explained on

page 7.

wall

mount

(fig 3)

Using the rear plate of the wall bracket as a

template, mark positions on the wall for four

screw fixings. Screw the bracket to the wall

using wall plugs and screws suitable for the

wall construction and the weight of the

loudspeaker.

Slide the speaker support arm onto the

bracket and attach the base plate.

Make the connections to the terminals on

the rear of the speaker, as explained on

page 7.

Carefully place the speaker onto the

speaker support arm, making sure that the

front extensions of the arm slot into the

recesses in the base of the speaker. Secure

the speaker onto the arm using the fixing

screw provided.

e82 / e83

e82 and e83 floorstanding speakers

perform best when positioned more than

0.3m from a rear wall and away from

corners (fig 1). Moving the speakers towards

a wall or corner will increase the amount of

bass, conversely moving the speakers away

from a wall or corner will increase the clarity,

articulation and tautness of bass. For good

two-channel performance the speakers

should be around 1.8 - 2.2m apart (fig 1).

Where speakers are used as part of a multi-

channel system this distance can be altered

to suit your room furnishings. Spend some

time moving the speakers and listening for

the optimum performance.

e8as1 / e8as2

e8as1 and e8as2 subwoofers give clean

and articulate bass when positioned at least

0.3m from a corner. However if a higher

level of bass output is demanded, a corner

position may provide this at the possible

expense of some clarity. Again it is

beneficial to spend time moving the

subwoofer and listening for the optimum

performance.

The e8as1 and e8as2 subwoofers are

designed to provide the low frequency

foundation and reproduction of low

frequency effects in a music or home theatre

system. The method of connection and

setup will depend on the electronics that

you connect to the subwoofer. Please read

through the instructions to determine how

best to use your subwoofer.

fig 1

fig 2

fig 3

System setup

Connecting

your

amplifier

The e series speakers are suitable for

bi-wiring and will benefit from careful

selection of partnering cables from your

amplifier. When bi-wiring, or bi-amping (fig 1),

remove the connecting links from between

the terminals at the rear of the speaker.

To connect using bare wires (fig 2), strip

10mm (1/2 inch) of insulation from each

cable. Loosen the terminal caps on the

speaker terminals to reveal the cross holes.

Twist the bared conductors together and

pass through the cross hole in the speaker

terminal, securing by screwing down the

terminal cap.

To connect using spade terminals (fig 3),

loosen the terminal caps on the speaker

terminals enough to locate the spades.

Tighten the terminal caps onto the spades

so that they are held securely.

Connect the positive speaker outlets on the

rear of your amplifier to the positive (red)

terminals on the rear of the speakers.

Similarly connect the negative speaker

outputs to the negative (black) terminals on

the speakers. Note that speaker cables

usually identify the positive conductor by

marking it with a stripe or raised ridge or

coloured band.

as1/

as2

To connect a stereo hi-fi amplifier it is

recommended that you connect the speaker

outputs of your amplifier to the speaker level

inputs of the subwoofer in parallel to the

connections made to your speakers.

To connect an AV multi-channel amplifier it

is recommended that you connect the LFE

line level input on the subwoofer to the

subwoofer output on your amplifier using an

RCA phono lead (not supplied).

Power

—

Set the subwoofer’s ON/OFF switch

to "Off." Then plug the power cord into an

AC outlet. You can turn the power on and off

manually using the switch, or you can leave

the mains power turned on and set the Auto

Power switch to "On," which will turn the

subwoofer on automatically when a signal

is detected at one of the inputs and off after

a period of inactivity.

setup

In a multi-channel system it is

recommended that you use the bass

management facilities on your AV amplifier.

As the subwoofer is best employed to

reproduce bass, all low frequency

information should be directed to the

subwoofer enabling the main speakers to

reproduce upper bass, midrange and treble

with optimum clarity.

If you are using the bass management of an

AV amplifier, set all speakers to SMALL in

your amplifier's speaker configuration and

set SUBWOOFER to ON. Where the crossover

frequency can be chosen set it to 80Hz.

Alternatively choose the preset configuration

for THX.

Set the Low Pass Crossover Frequency

control on the subwoofer to 140Hz (on the

e8as2 set the LFE switch to ON). Adjust the

volume control to its mid position.

Use the distance parameters in your AV

amplifier speaker setup to set the distance

from each set of speakers to your listening

position.

Use the channel level adjustment in your AV

amplifier speaker setup to set the individual

output from each speaker. If you have a

sound level meter adjust the individual level

of each channel for a reading of 75dB at the

listening position. If you do not have access

to a sound level meter, set the channel

levels so that they sound equally loud at the

listening position.

Stereo

setup

In a hi-fi system without bass management

you must adjust the LOW PASS CROSSOVER

control on the subwoofer in conjunction with

the SUBWOOFER VOLUME control to achieve

a blend to your main speakers. The e8as1

and e8as2 subwoofers can be used with

the e82 and e83 floorstanding speakers in a

hi-fi system. (Note that the e80 is not

suitable for use in a hi-fi system without

bass management).

For the e82 speakers, start by setting the

LOW PASS CROSSOVER control to midway

and adjust the SUBWOOFER volume level to

provide a natural level of bass support

when playing music discs. For the e83

speakers, start by setting the LOW PASS

CROSSOVER control to between the 40Hz

and the midway position.

Adjusting

the

controls

Once you have completed the settings you

should prepare to fine-tune the subwoofer

controls. Choose a multi-channel disc with

natural bass qualities - a music disc is best.

Adjust the control on the subwoofer's rear

panel marked PHASE to tune the blend

between the subwoofer and speakers.

Depending on your room acoustics the

sound will be fuller and more coherent with

the switch in the 0° or 180° position. Use

your judgement to set the switch to the best

sounding position.

On the e8as2 you also have fine control

over phase. Use the variable PHASE control

to achieve the fullest and clearest bass

response. In conjunction with the PHASE

switch, the phase can be varied over 180°.

Adjust the SUBWOOFER VOLUME control to

give bass output that is in balance with your

main speakers. Initially you may prefer the

subwoofer output at a relatively high level,

but this can become tiring, with an over-

emphasis on bass on extended listening.

Turn the volume down by degrees until the

subwoofer is not heard individually but

rather as an extension to the main

speakers.

On the e8as2 you can fine tune the bass

performance to suit your room. If the bass is

boomy, or appears uncontrolled at very low

frequencies, switch the SUBSONIC FILTER to

ON. Adjust the BASS CONTOUR to control

output at the very low frequencies.

8 9

General information

Loudspeaker

maintenance

Use the supplied cloth to polish dust and

fingermarks from the speakers. Rub the

surface to be cleaned with the inner cloth.

Remove tarnish and buff to a high shine with

the dark outer cloth. Do not use spray

polishes or solvent cleaners as these may

damage the highly polished multi-layer

lacquer finish. If necessary clean the speaker

grilles carefully with a soft brush.

Product

service

Should a fault occur with your loudspeakers

please pack them correctly, using the

original packaging.

Product for service should be returned to the

appointed dealer from whom you

purchased the product. If you experience

difficulties or there is no Mission dealer in

your area, contact the Mission distributor for

your country or the main service centre for

your region.

Important

Notice

Users

–

e8as1, e8as2

The power cord on your Mission powered

subwoofer is supplied with a plug

incorporating a fuse, the value of which is

indicated on the pin face of the plug. Should

the fuse need to be replaced, an ASTA or BSI

approved BS1362 fuse must be used of the

same rating. If the plug is cut off it must NOT

be re-used. Dispose of any such plug safely.

There is a danger of electric shock if a cut-off

plug is inserted into a mains socket.

The wires in the mains lead are coloured in

accordance with the following code:

Blue - Neutral: Brown - Live.

As the colours of the wires in the mains lead

may not correspond with the markings

identifying the terminals in the replacement

mains plug, proceed as follows:

The wire coloured Blue must be connected

to the terminal marked with the letter "N" or

coloured Black. The wire coloured Brown

must be connected to the terminal marked

with the letter "L" or coloured Red.

Recommended Amplifier:

50 - 150 W 50 - 150 W 50 - 150 W 50 - 200 W

Enclosure: 2-way sealed box 2-way sealed box 3-way reflex loaded 2-way ABR loaded

Frequency Response ±3dB: 80 Hz - 30 kHz 80 Hz - 30 kHz 48 Hz - 30 kHz 44 Hz - 30 kHz

Sensitivity SPL/M @ 2.83V: 85 dB 90 dB 90 dB 90 dB

Impedance: 8 Ohms compatible 8 Ohms compatible 8 Ohms compatible 8 Ohms compatible

(minimum 4.0 Ohms) (minimum 4.6 Ohms) (minimum 4.0 Ohms) (minimum 4.0 Ohms)

Bass: 110 mm Paramid-S Twin 110 mm Paramid-S 4 x 110 mm Paramid-S Twin 165 mm Paramid-S

Mid: - - 110 mm Paramid-S -

Treble: 25 mm Viotex-S 25 mm Viotex-S 25 mm Viotex-S 25 mm Viotex-S

Effective Volume: 3.75 litres 5.75 litres 23 litres 40 litres

Dimensions (H x W x D): 284 x 160 x 250 mm 403 x 160 x 250 mm 956 x 300 x 334 mm 1108 x 330 x 360 mm

11.2 x 6.3 x 9.8 inches 15.9 x 6.3 x 9.8 inches 37.6 x 11.8 x 13.2 inches 43.6 x 13 x 14.2 inches

Weight: 6 kg 8.7 kg 19.7 kg 22.1 kg

13.2 lbs 19.2 lbs 43.4 lbs 48.7 lbs

e80 e81 e82 e83

Specifications

Recommended Amplifier: 50 - 150 W Integrated 350 W Integrated 500 W

Enclosure: 2-way sealed box ABR loaded sealed box

Frequency Response ±3dB: 80 Hz - 30 kHz 36 Hz - 150 Hz 28 Hz - 280 Hz

Sensitivity SPL/M @ 2.83V:

90 dB - -

Impedance: 8 Ohms compatible

(minimum 4.6 Ohms)

Bass: Twin 110 mm Paramid-S 250 mm + twin ABR 4 x 210 mm

Mid: ---

Treble: 25 mm Viotex-S - -

Effective Volume: 6.5 litres 30 litres 46 litres

Dimensions (H x W x D): 172 x 443 x 250 mm 415 x 365 x 400 mm 430 x 400 x 560 mm

6.8 x 17.4 x 9.8 inches 16.3 x 14.4 x 15.7 inches 16.9 x 15.7 x 22 inches

Weight: 9.1 kg 17.3 kg 32 kg

20.1 lbs 38.1 lbs 70.5 lbs

e8c e8as1 e8as2

Specifications

Mission reserves the right to change specifications without notice. E & OE

Warning:

When an amplifier is driven beyond its power output capabilities it will produce distorted results which will

quickly damage your speakers by overheating. Make sure that your amplifier is not left unattended when playing, for

example at parties, and turn the volume control down at the first sign of audible distortion.

CORD GRIP

FUSE

BROWN

(LIVE)

OUTER

SLEEVE

BLUE

(NEUTRAL)

Page is loading ...

Mission Elegante e80 User manual

Brand: Mission

Model: Elegante e80

Category: Loudspeakers

Type: User manual

Download PDF

report

in other languages

français: Mission Elegante e80 Manuel utilisateur
español: Mission Elegante e80 Manual de usuario
Deutsch: Mission Elegante e80 Benutzerhandbuch

Mission Elegante e80 User manual

Mission Elegante e80 User manual

in other languages

Related papers

Other documents