Kichler Lighting 337010IV User manual

Brand
Kichler Lighting
Model
337010IV
Type
User manual
337010
WARNING
To avoid fire, shock and serious personal injury, follow these instructions:
1. Carefully read and retain this Instruction Manual for future reference.
2. To avoid possible electrical shock, be sure the electricity is turned off at
the main panel by removing the fuse or opening the circuit breaker.
3. This control switch is designed for use with "Ceiling Fans" ONLY. DO
NOT use with any other type of electrical appliance.
4. All wiring must conform to national and local electrical codes. If you feel
you do not have enough electrical knowledge, have a licensed electrician
install the control.
5. The amperage for your fan should not exceed 1.25A. The total wattage
for the lights 300W.
INSTALLATION AND OPERATING
INSTRUCTIONS
1. Disconnect the power and remove the existing wall plate and switch. (Fig. 1)
2. Push BOTH slide switches all the way down to the OFF position. (Fig.2)
3. Make each of the wire connections illustrated in Figure 3. Secure each
with the wire nuts provided.
Black wire going to the fan (motor) to the Black wire from the Switch.
In the Ceiling Outlet Box, connect the White (neutral) wire coming from
the Fan to the White (neutral) wire from the Household Supply.
Connect the Blue (For Light) wire coming from the fan to the Blue (For
Light) wire from the Switch.
Connect the Black & White (AC IN L) from the switch to the Black wire
going to the Household Supply.
4. If your ceiling outlet box has a ground wire (green or bare copper) connect
it to the ground wire from the ceiling fan and/or the ceiling mounting
bracket.
Fig. 2
Fig. 1
Fig. 3
1
DUAL SLIDE WALL CONTROL
INSTALLATION INSTRUCTIONS
Wall plate
Switch
Outlet box
Light
switch
Speed
switch
Blue (for light)
light switch lead
Black/white (AC IN L)
to hot household
Black (to motor)
speed control lead
Green ground ( ) lead
Fan
SUPPLY CIRCUIT
BLACK/
WHITE
BLACK
BLUE
BLACK
BLUE
BLACK
Ground Conductor
Outlet Box
Green Ground Lead
Ground to Downrod
GREEN
WHITE WHITE
5. Attach the Speed/Light Switch to the wall outlet box and secure with the
two screws provided. (Fig 4)
6. Attach the wall plate to the switch with the two screws provided. (Fig. 4)
NOTE: If your fan has the original pull chain speed control, you
MUST set and leave this control on High Speed. The On/Off switch
(pull chain) on the ceiling fan light fixture must be set to ON.
Fig. 4
Fig. 5
2
Wall plate
Switch
Outlet box
Screws
Screws
Restore power to the ceiling fan and test for proper operation.
Speed Slide Switch: The Slider is used to set each fan speed
separately. Move it up or down to select the desired speed.
1= High Speed
2 = Medium High Speed
3 = Medium Speed
4 = Low Speed
= Fan Off
Light Slide Switch: This Slider turns the light fixture On or OFF
and adjust the Brightness of the fixture. OFF is all the way down.
OPERATING YOUR WALL CONTROL
If either slide switch does not work correctly, check the following.
● Check the main power supply and make sure the circuit is
powered ON.
● Make sure the Manual Speed Pull Chain is set on HIGH SPEED.
● Make sure the Light Fixture pull chain is set in the ON position.
TROUBLESHOOTING GUIDE
Warning!
Hook up “in series” only
Do not connect to hot and common wire of electric circuit or
switch will be damaged. Refer to Fig. 6.
Fig. 6
3
6-32" x 3/4"
SCREWS
6-32" x 1/4"
SCREWS
BLACK
BLACK
BLUE
BLUE
BLACK
BLACK
WHITE
AC 120V
INPUT
BLACK WHITE
WHITE
GREEN
TO GROUND
BLACK/
WHITE
BLACK
BLACK
FAN
Date Issued: 8/8/08
BLACK
(AC L IN)
BLUE
BLUE
GREEN TO
GROUND
BLACK
  • Page 1 1
  • Page 2 2
  • Page 3 3

Kichler Lighting 337010IV User manual

Brand
Kichler Lighting
Model
337010IV
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents