Hampton Bay Y52YH5-06 Installation And Operation Instruction Manual

Brand: Hampton Bay

Model: Y52YH5-06

Category: Household fans

Type: Installation And Operation Instruction Manual

READ AND SAVE THESE INSTRUCTIONS

FAN RATING AC 120V. 60Hz

UL LISTED MODEL : AC-552

MODEL# Y52YH5-06

CEILING FAN INSTALLATION AND

OPERATION INSTRUCTION

2. PACKAGE CONTENTS

npack your fan and check the contents.

ou should have the following items;

. Fan blades (5)

. Hanger bracket

. Canopy

. Ball/downrod assembly (1)

& extra downrod (1)

. Fan motor assembly

. Set of blade brackets (5)

. Switch housing

. Light kit

. Glass shade

. Pull chain and fob (2)

. 60 Watt medium base bulbs (2)

. Package hardware

1) Mounting hardware :

wire nuts(3)

2) Blade attachment hardware:

screws(16)

3) Balance Kit

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

. TOOLS AND MATERIALS

REQUIRED

. To reduce the risk of electric shock,

insure electricity has been turned off

at the circuit breaker or fuse box

before beginning.

. All wiring must be in accordance with

the National Electrical Code and local

electrical codes. Electrical installation

should be performed by a qualified

licensed electrician.

. WARNING: To reduce the risk of

electrical shock and fire, do not use

this fan with any solid-state fan speed

control device.

. WARNING: To reduce the risk of

personal injury, use only the two steel

screws (and lock washers) provided

with the outlet box for mounting to

the outlet box. Most outlet boxes

commonly used for the support of

lighting fixtures are not acceptable for

fan support and may need to be

replaced, consult a qualified electrician

if in doubt.

. The outlet box and support structure

must be securely mounted and

capable of reliably supporting a

minimum of 50 pounds. Use only CUL

Listed outlet boxes marked "FOR FAN

SUPPORT".

. The fan must be mounted with a

minimum of 7 feet clearance from the

trailing edge of the blades to the floor.

7. Do not operate reversing switch whi

fan blades are in motion. Fan must b

turned off and blades stopped befo

reversing blade direction.

8. Avoid placing objects in the path of th

blades.

9. To avoid personal injury or damage

the fan and other items, be cautiou

when working around or cleaning th

fan.

10. Do not use water or detergents whe

cleaning the fan or fan blades. A d

dust cloth or lightly dampened clo

will be suitable for most cleaning.

11. After marking electrical connection

spliced conductors should be turne

upward and pushed carefully up in

outlet box. The wires should be sprea

apart with the grounded conduct

and the equipment-groundin

conductor on one side of the outl

box.

12. Electrical diagrams are reference on

ly.

Light kit that are not packed with th

fan must be CUL Listed and marke

suitable for use with the model fan yo

are installing. Switches must be CU

General Use Switches. Refer to th

Instructions packaged with the lig

kits and switches for proper assembly

3. SAFETY RULES

WARNING

TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX

MARKED "ACCEPTABLE FOR FAN

SUPPORT".

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR

AFTER INSTALLATION. DO NOT

INSERT OBJECTS IN THE PATH OF THE

BLADES.

. MOUNTING OPTIONS

If there isn't an existing CUL listed

mounting box, then read the following

instructions. Disconnect the power by

removing fuses or turning off circuit

breakers.

Secure the outlet box directly to the

building structure. Use appropriate

fasteners and building materials. The

outlet box and its support must be able to

fully support the moving weight of the fan

(at least 50 lbs). Do not use plastic outlet

boxes.

Figures 1,2 and 3 are examples of different

ways to mount the outlet box.

Note: You may need a longer downrod to

maintain proper blade clearance when

installing on a steep, sloped ceiling. (Fig. 3)

Outlet box

Provide strong

support

Recessed

outlet box

Ceiling

mounting

plate

Outlet box

Figure 1

Figure 3

Figure 4

Outlet box

Figure 2

Angled ceiling

maximum

angle

EMEMBER to turn off the power. Follow

he steps below to hang your fan properly:

tep 1. Pass the 120-volt supply wires

hrough the center hole in the ceiling

anger bracket as shown in Fig. 5.

tep 2. Secure the hanger bracket to the

eiling outlet box with the screws and

ashers provided with your outlet box.

tep 3. Remove the hanger pin, lock pin

nd set screws from the top of the motor

ssembly.

tep 4. Route wires exiting from the top

f the fan motor through the canopy and

hen through the ball / downrod. (Fig. 6)

tep 5. Align the holes at the bottom of

he downrod with the holes in the collar

n top of the motor housing (Fig.6).

arefully insert the hanger pin through

he holes in the collar and downrod. Be

areful not to jam the pin against the

iring inside the downrod. Insert the

ocking pin through the hole near the end

f the hanger pin until it snaps into its

ocked position. (Fig. 6)

tep 6. Tighten two set screws on top of

he fan motor firmly. (Fig. 6)

tep 7. Place the downrod ball into the

anger bracket socket. (Fig. 7)

HANGING THE DOWNROD (OPTIONAL)

OTE: Your fan comes with a 4" downrod

ttached to the hanger ball. In addition

ou have been provided with a 6"

ownrod to use if desired. If you choose

o use the 6" downrod, perform the

ollowing steps.

. Remove the hanger ball from the 4"

ownrod by loosening the set screw at

he top of the downrod which holds the

anger ball to the downrod.

. Slide the hanger ball down the

ownrod and remove the support pin.

. Insert the support pin in the holes at the

op of the 6" downrod and slide the

anger ball up the 6" downrod. Make sure

he support pin is properly seated in the

rooves in the top of the hanger ball.

. Tighten the set screw firmly.

5. Hanging the Fan

Mounting screws

(supplied with

electrical box)

Hook

Hanger

bracket

UL Listed

electrial

box

Figure 5

Figure 6

Figure 7

120V Wires

Washers

Registration slot

Downrod

Canopy

Set screws

Hitch pin

Lock pin

. MAKE THE ELECTRIC

CONNECTIONS

emember to disconnect the power.

ollow the steps below to connect the fan

o your household wiring. Use the wire

onnecting nuts supplied with your fan.

ecure the connectors with electrical tape.

ake sure there are no loose strands or

onnections.

tep 1 Connect the fan supply (black) wire

nd light supply (blue) wire to the black

ousehold supply wire as shown in Figure 8.

tep 2. Connect the neutral fan (white)

ire to the white neutral household wire.

tep 3 Connect the fan ground wire

(

green) to the household ground wire.

tep 4 After connecting the wires, spread

hem apart so that the green and white

ires are on one side of the outlet box and

he black and the blue wires are on the

ther side.

tep 5 Turn the connecting nuts upward

nd push the wiring into the outlet box.

igures 9 and 10 illustrate the wiring

onnections for optional wall control. (The

ire color out of wall control may vary, see

all control's installation manual for

orrect wire connections.)

OTE: LIGHT KITS ARE AVAILABLE AT YOU

AVOY HOUSE RETAILER. THE FAN IS

LREADY WIRED TO SUPPORT THE LIGHT

IT OPTION.

ARNING: TO REDUCE THE RISK OF FIRE,

LECTRIC SHOCK, OR OTHER PERSONAL

NJURY. MOUNT FAN ONLY ON AN OUTLET

OX OR SUPPORTING SYSTEM MARKED

ACCEPTABLE FOR FAN SUPPORT".

Figure 8

Figure 9

BLK

BLUE

BLK

GRN

WIRING

BOX

WIRING

BOX

GROUND TO

MOUNTING

BRACKET

OR DOWNROD

GROUND TO

MOUNTING

BRACKET

OR DOWNROD

BLUE

BLK

FAN

LIGHT

POWER LINES 120V

BLK

BLUE

BLK

FAN

LIGHT

BLK

BLUE

LIGHT

SWITCH

GREEN GROUND

Figure 10

GROUND TO

MOUNTING

BRACKET

OR DOWNROD

POWER LINES 120V

GREEN

GROUND

WIRING

BOX

BLK

BLUE

BLK

FAN

LIGHT

BLUE

BLK

LIGHT

FAN

. FINISHING THE

INSTALLATION

tep 1. Slide the canopy up to the

eiling and over the two screws on

anger bracket. Rotate canopy clockwise

ntil tight.

ote: adjust the canopy screws as

eeded until the canopy is snug. (Fig. 11)

Figure 11

Outlet box

Hanger

bracket

Canopy

Screws

. ATTACHING THE FAN

BLADES

tep 1 Attach the blades to the blade

rackets using the screws and rubber

ashers provided as shown in Figure 12.

tart a screw into the bracket, but do not

ighten. Repeat for the other 2 screws and

ashers.

tep 2 Tighten each screw securely

tarting with the center screw. Make sure

he blade is straight.

tep 3 Fasten the blade assemblies to the

otor by insert the tab from the blade

rackets to the slot in the bottom motor

ousing, then tighten the two screws and

ashers already installed in the blade

rackets (Figure 13).

tep 4 Install an optional light kit if

you wish. Follow the instructions

included with the kit.

Figure 12

Figure 13

Blade

Blade bracket

Screws

Rubber

washers

Motor

Blade

bracket

Slot

Tab

Figure 14

Figure 15

. INSTALLING THE LIGHT

KIT

OTE: Before starting installation,

isconnect the power by turning off the

ircuit breaker or removing the fuse at

use box.

urning power off using the fan switch is

ot sufficient to prevent electric shock.

. Remove the plug from the switch

ousing (Fig. 17), attach the light kit to the

witch housing by feeding the light kit

ires (black and white) through the hole

f switch housing and then screw it onto

he switch housing by nut & lock washer

rovided. Be sure it is tight enough to

revent light kit from vibrating loose.

OTE: For easy pull chain installation, be

ure that the location of the 3 speed

witch on the switch housing and the pull

hain holder on the light kit are in suitable

ocations as shown on Fig. 14 and 15.

. Locate two single white and blue wires

n the switch housing labeled FOR LIGHT.

. Make the polarized plug connections:

- White to white

- Blue to black

. While holding the light kit assembly

nder your fan, snap together the wire

onnection plugs .

. Carefully push all wires back into the

witch housing, then install the light kit

ssembly onto the mounting plate with 3

crews provided. Be sure to tighten all

crews. (Fig. 15)

. Pass the two pull chains on the switch

ousing through the chain holders

ocated on the light kit, install the fobs to

he pull chains. (Fig. 15)

. Install two 60 watt (max.) bulbs

(

included) and glass shade with four

humb screws, do not over tighten.

. Restore power and your light kit is ready

or operation.

. If the light kit does not work, turn off the

lectricity and lower either canopy on

our ceiling fan to make sure the blue wire

s connected to the black household wire.

Switch housing

Light kit

Nut

Lock washer

Pull chain

Plug

Pull chain holder

Mounting plate

Connection plug

Screws

Thumb screws

Light kit assembly

Glass shade

Bulbs

Pull chain holder

10. OPERATING YOUR FAN

OTE: Wait for fan to stop before

hanging the setting of the slide

witch.

urn on the power and check the

peration of your fan. The pull chain

ontrols the fan speed as follows: 1

ull- High, 2 pulls-Medium, 3 pulls-

ow, and 4 pulls-Off.

peed settings for warm or cool

eather depend on factors such as the

oom size, ceiling height, number of

ans and so on.

he slide switch controls directions:

orward (switch down) or reverse

(

switch up)

arm weather - (Forward) A

ownward airflow creates a cooling

ffect as shown in Fig. 16. This allows

ou to set your air conditioner on a

armer setting without affecting your

omfort.

ool weather - (Reverse) An upward

irflow moves warm air off the ceiling

rea as shown in Fig. 17. This allows

ou to set your heating unit on a

ooler setting without affecting your

omfort.

Figure 16

Figure 17

roblem

an will not start.

an sounds

oisy.

Solution

1. Check circuit fuses or breakers.

2. Check line wire connections to the fan and switch wire connection

in the switch housing.

CAUTION: Make sure main power is off.

1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade bracket to the mot

hub is tight.

3. Make sure wire nut connections are not rubbing against each oth

or the interior wall of the switch housing.

CAUTION: Make sure main power is off.

4. Allow a 24-hour "breaking-in" period. Most noise associated with

new fan disappear during this time.

5. If using an optional light kit, make sure the screws securing th

glassware are tight. Check that light bulb is also secure.

6. Some fan motors are sensitive to signals from solid-state variab

speed controls. If you have installed this type of control, choose an

install another type of control.

7. Make sure the upper canopy is a short distance from the ceiling.

should not touch the ceiling.

1. TROUBLESHOOTING

These are approximate measures. They do not include Amps and Wattage used by th

light kit.

12. SPECIFICATIONS

Fan Size

Speed Volts Amps Watts RPM CFM N.W. G.W. C.F.

52"

120

0,20

0,35

0,49

111

163

1025

3500

5400

9,7

kgs

11.8

kgs

1,81

Low

Medium

High

Hampton Bay Y52YH5-06 Installation And Operation Instruction Manual

Brand: Hampton Bay

Model: Y52YH5-06

Category: Household fans

Type: Installation And Operation Instruction Manual

Download PDF

report

Hampton Bay Y52YH5-06 Installation And Operation Instruction Manual

Hampton Bay Y52YH5-06 Installation And Operation Instruction Manual

Related papers

Other documents