Taylor Model 8756 User manual

Brand: Taylor

Model: Model 8756

Type: User manual

This manual is also suitable for

Frozen Dessert Maker Model 8756

OPERATOR'S

MANUAL

Model 8756

Single Stage Pump

Soft Serve Freezer

Original Operating Instructions

069071-M 11/15/10 (Original Publication)

(Updated 8/14/14)

Complete this page for quick reference when service is required:

Taylor Distributor:

Address:

Phone:

Fax:

E-mail:

Service:

Parts:

Date of Installation:

Information found on the data label:

Model Number:

Serial Number:

Electrical Specs: Voltage Cycle

Phase

Maximum F use Size: A

Minimum Wire Ampacity: A

E 2010 Carrier Commercial Refrigeration, Inc.

069071-M

Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this

work may be aviolationof Copyright Law of the United States of America and other countries, couldresult

in the awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result

Taylor Company

a division of Carrier Commercial Refrigeration, Inc.

750 N. Blackhawk Blvd.

Rockton, IL 61072

Model 8756 Table of Contents

Table of Contents

Section 1 To the Installer 1............................................

Installer Safety 1........................................................

Site Preparation 1.......................................................

Air Cooled Units 1.......................................................

Water Connections (Water Cooled Units Only) 2............................

Electrical Connections 2.................................................

Beater Rotation 3.......................................................

Refrigerant 3...........................................................

Section 2 To the Operator 4...........................................

Section 3 Safety 5....................................................

Section 4 Operator Parts Iden t ificatio n 8...............................

Beater Door Assembly 10.................................................

Air/Mix Pump Assembly 11................................................

Accessories 12..........................................................

Section 5 Important: To the Operator 13.................................

Symbol Definitions 14....................................................

Power Switch 14.........................................................

Indicator Lights - MIX LOW and MIX OUT 14................................

Reset Button 14.........................................................

MIX REF 14.............................................................

Standby 14..............................................................

Wash 15................................................................

Auto 15.................................................................

Pump 15................................................................

Adjustable Draw Handle 15...............................................

Section 6 Operating Procedures 16.....................................

Assembly 16............................................................

Air/Mix Pump Assembly 21................................................

Sanitizing 25............................................................

Priming 28..............................................................

Table of Contents Model 8756

Table of Contents - Page 2

Closing Procedure 29....................................................

Draining Product From the Freezing Cylinder 30.............................

Rinsing 30..............................................................

Cleaning 31.............................................................

Disassembly 32..........................................................

Brush Cleaning 33.......................................................

Section 7 Important: Operator Checklist 34..............................

During Cleaning and Sanitizing 34.........................................

Troubleshooting Bacterial Count 34........................................

Regular Maintenance Checks 34...........................................

The Air/Mix Pump 35.....................................................

Section 8 Troubleshooting Guide 36....................................

Section 9 Parts Replacement Schedule 41...............................

Section 10 Limited Warranty on Equipment 42............................

Section 11 Limited Warranty on Parts 44.................................

Section 12 Parts L ist 47.................................................

Wiring Diagram 56.......................................................

Note: Continuing research results in stead y improvements; therefore, information

in this manual is subject to change without notice.

Note: Only instructions originating from the factory or its authorized translation

representative(s) are considered to be the original set of in structions.

E 2010 Carrier Commercial Refrigeration, Inc. (Original Publication)

(Updated August, 2014)

069071-M

Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this

work may be a violationof Copyright Law of the United States of Americaand other countries, could result

in the awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result

Taylor Company

a division of Carrier Commercial Refrigeration, Inc.

750 N. Blackhawk Blvd.

Rockton, IL 61072

Model 8756 To the Installer

131220

Section 1 To the Installer

The following information has been included in the

manual as safety and regulatory guidelines. For

complete installation instructions, please see the

Installation Checklist.

Installer Safety

In all areas of the world, equipment should

be installed in accordance with existing local codes.

Please contact your local authorities if you have any

questions.

Care should be taken to ensure that all basic safety

practices are followed during the installation and

servicing activities related to the installation and

servicing of Taylor equipment.

S Only authorized Taylor service personnel

should perform installation and repairs on

the equipment.

S Authorized service personnel should consult

OSHA Standard 29CFRI910.147 or the

applicable code of the local area for the

industry standards on lockout/tagout

procedures before beginning any installation

or repairs.

S Authorized service personnel must ensure

that the proper PPE is available and worn

when required during installation and

service.

S Authorized service personnel must remove

all metal jewelry, rings, and watches before

working on electrical equipment.

The main power supply(s) to the freezer

must be disconnected prior to performing any

repairs. Failure to follow this instruction may result in

personal injury or death from electrical shock or

hazardous moving parts as well as poor

performance or damage to the equipment.

Note:Allrepairsmustbeperformedbyan

authorized Taylor Service Technician.

This unit has many sharp edges that can

cause severe injuries.

Site Preparation

Review the area where the unit will be installed

before uncrating the unit. Make sure all possible

hazards to the user or equipment have been

addressed.

For Indoor Use Only: This unit is designed to

operate indoors, under normal ambient

temperatures of 70_-75_F(21_-24_C). The freezer

has successfully performed in high ambient

temperatures of 104_(40_C) at reduced capacities.

This unit must NOT beinstalledinanarea

where a water jet or hose can be used. NEVER use

a water jet or hose to rinse or clean the unit. Failure

to follow this instruction may result in electrocution.

This unit must be installed on a level surface

to avoid the hazard of tipping. Extreme care should

be taken when moving this equipment for any

reason. Two or more people are required to safely

move this unit. Failure to comply may result in

personal injury or equipment damage.

Uncrate the unit and inspect it for damage. Report

any damage to your Taylor Distributor.

This piece of equipment is made in the USA and has

USA sizes of hardware. All metric conversions are

approximate and vary in size.

Air Cooled Units

DO NOT obstruct air intake and discharge openings:

Air cooled units require a minimum of 3” (76 mm) of

clearance around all sides of the freezer and 12”

(305 mm) on top to allow for adequate air flow

across the condenser(s). Failure to allow adequate

clearance can reduce the refrigeration capacity of

the freezer and possibly cause permanent damage

to the compressor.

Model 8756To the Installer

Water Connections

(Water Cooled Units Only)

An adequate cold water supply must be provided

with a hand shut-off valve. On the underside of the

base pan, two 3/8” I.P.S. (for single-head units) or

two 1/2” I.P.S. (for double-head units) water

connections for inlet and outlet have been provided

for easy hook-up. 1/2” inside diameter water lines

should be connected to the machine. (Flexible lines

are recommended, if local codes permit.) Depending

on local water conditions, it may be advisable to

install a water strainer to prevent foreign substances

from clogging the automatic water valve. There will

be only one water “in” and one water “out”

connection for both single-head and double-head

units. DO NOT install a hand shut-off valve on the

water “out” line! Water should always flow in this

order: first, through the automatic water valve;

second, through the condenser; and third, through

the outlet fitting to an opentrapdrain.

A back flow prevention device is

required on the incoming water connection side.

Please refer to the applicable National, State, and

local codes for determining the proper configuration.

Electrical Connections

In the United States, this equipment is intended to

be installed in accordance with the National

Electrical Code (NEC), ANSI/NFPA 70-1987. The

purpose of the NEC code is the practical

safeguarding of persons and property from hazards

arising from the use of electricity. This code contains

provisions considered necessary for safety. In all

other areas of the world, equipment should be

installed in accordance with the existing local codes.

Please contact your local authorities.

FOLLOW YOUR LOCAL ELECTRICAL CODES!

Each unit requires one power supply for each data

label on the unit. Check the data label(s) on the

freezer for branch circuit overcurrent protection or

fuse, circuit ampacity, and other electrical

specifications. Refer to the wiring diagram provided

inside of the electrical box for proper power

connections.

CAUTION: THIS EQUIPMENT MUST BE

PROPERLY GROUNDED! FAILURE TO DO SO

CAN RESULT IN SEVERE PERSONAL INJURY

FROM ELECTRICAL SHOCK!

This unit is provided with an equipotential

grounding lug that is to be properly attached to the

rear of the frame by the authorized installer. The

installation location is marked by the equipotential

bonding symbol (5021 of IEC 60417-1) on both the

removable panel and the equipment's frame.

S Stationary appliances which are not

equipped with a power cord and a plug or

another device to disconnect the appliance

from the power source must have an all-pole

disconnecting device with a contact gap of

at least 3 mm installed in the external

installation.

S Appliances that are permanently connected

to fixed wiring and for which leakage

currents may exceed 10 mA, particularly

when disconnected or not used for long

periods or during initial installation, shall

have protective devices such as a GFI, to

protect against the leakage of current,

installed by the authorized personnel to the

local codes.

Model 8756 To the Installer

131220

S Supply cords used with this unit shall be

oil-resistant, sheathed flexible cable not

lighter than ordinary polychloroprene or oth-

er equivalent synthetic elastomer-sheathed

cord (Code designation 60245 IEC 57) in-

stalled with the proper cord anchorage to

relieve conductors from strain, including

twisting, at the terminals and protect the in-

sulation of the conductors from abrasion.

If the supply cord is damaged, it must be

replaced by an authorized Taylor service

technician in order to avoid a hazard.

Beater Rotation

Beater rotation must be clockwise as viewed

looking into the freezing cylinder.

The following procedures must be

performed by an authorized Taylor service

technician.

To correct the rotation on a three-phase unit,

interchange any two incoming power supply lines at

freezer main terminal block only.

To correct rotation on a single-phase unit, change

the leads inside the beater motor. (Follow the

diagram printed on the motor.)

Electrical connections are made directly to the

terminal block provided in the main control box.

Refrigerant

In consideration of our environment, Taylor

uses only HFC refrigerants. The HFC refrigerant

used in this unit is R404A. This refrigerant is

generally considered non-toxic and non-flammable,

with an Ozone Depleting Potential (ODP) of zero (0).

However, any gas under pressure is potentially

hazardous and must be handled with caution.

NEVER fill any refrigerant cylinder completely with

liquid. Filling the cylinder to approximately 80% will

allow for normal expansion.

Use only R404A refrigerant that conforms

to the AHRI standard 700 specification. The use of

any other refrigerant may expose users and

operators to unexpected safety hazards.

Refrigerant liquid sprayed onto the skin may

cause serious damage to tissue. Keep eyes and skin

protected. If refrigerant burns should occur, flush

immediately with cold water. If burns are severe,

apply ice packs and contact a physician

immediately.

Taylor reminds technicians to be cautious of

government laws regarding refrigerant recovery,

recycling, and reclaiming systems. If you have any

questions regarding these laws, please contact the

factory Service Department.

WARNING: R404A refrigerant used in

conjunction with polyolester oils is extremely

moisture absorbent. When opening a refrigeration

system, the maximum time the system is open must

not exceed 15 minutes. Cap all open tubing to

prevent humid air or water from being absorbed by

the oil.

Model 8756To the Operator

131220

Section 2 To the Operator

The unit you have purchased has been carefully

engineered and manufactured to give you

dependable operation. This unit, when properly

operated and cared for, will produce a consistent

quality product. Like all mechanical products, it will

require cleaning and maintenance. A minimum

amount of care and attention is necessary if the

operating procedures outlined in this manual are

followed closely.

This Operator's Manual should be read before

operating or performing any maintenance on the

unit.

Your Taylor unit will NOT compensate for and/or

correct any errors made during the set-up or filling

operations. Thus, the initial assembly, set-up, and

priming procedures are of extreme importance. It is

strongly recommended that all personnel

responsible for the unit's operation, including

assembly and disassembly, go through these

procedures together in order to be properly trained

and to make sure that all understand their role in

using and maintaining the unit.

In the event you should require technical assistance,

please contact your local authorized Taylor

Distributor.

Note: Your Taylor warranty is valid only if the parts

are authorized Taylor parts, purchased from the

local authorized Taylor Distributor, and only if all

required service work is provided by an authorized

Taylor service technician. Taylor reserves the right

to deny warranty claims on units or parts if

non-Taylor approved parts or incorrect refrigerant

were installed in the unit, system modifications were

performed beyond factory recommendations, or it is

determined that the failure was caused by abuse,

misuse, neglect, or failure to follow all operating

instructions. For full details of your Taylor Warranty,

please see the Limited Warranty section in this

manual.

If the crossed out wheeled bin symbol is

affixed to this unit, it signifies that this unit is

compliant with the EU Directives as well as other

similar end of life legislation in effect after August

13, 2005. Therefore, it must be collected separately

after its use is completed, and cannot be disposed

as unsorted municipal waste. The user is

responsible for returning the unit to the appropriate

collection facility, as specified by your local code.

For additional information regarding applicable local

disposal laws, please contact the municipal waste

facility and/or local authorized Taylor distributor.

Compressor Warranty Disclaimer

The refrigeration compressor(s) on this unit are

warranted for the term stated in the Limited

Warranty section in this manual. However, due to

the Montreal Protocol and the U.S. Clean Air Act

Amendments of 1990, many new refrigerants are

being tested and developed, thus seeking their way

into the service industry. Some of these new

refrigerants are being advertised as drop-in

replacements for numerous applications. It should

be noted that in the event of ordinary service to this

unit's refrigeration system, only the refrigerant

specified on the affixed data label should be

used. The unauthorized use of alternate refrigerants

will void your Taylor compressor warranty. It is the

unit owner's responsibility to make this fact known to

any technician he employs.

It should also be noted that Taylor does not warrant

the refrigerant used in its equipment. For example, if

the refrigerant is lost during the course of ordinary

service to this unit, Taylor has no obligation to either

supply or provide replacement refrigerant either at

billable or unbillable terms. Taylor will recommend a

suitable replacement if the original refrigerant is

banned, obsoleted, or no longer available during the

five (5) year Taylor warranty of the compressor.

From time-to-time Taylor may test new refrigerant

alternates. Should a new refrigerant alternate prove,

through Taylor's testing, that it would be accepted as

a drop-in replacement for this unit, then the

disclaimer in this “Compressor Warranty Disclaimer”

section will not apply to the use of the alternate

refrigerant approved by Taylor.

To find out the current status of an alternate

refrigerant as it relates to your compressor warranty,

call Taylor or your local authorized Taylor distributor.

Be prepared to provide the Model/Serial Number of

the unit in question.

Note: Continuing research results in steady

improvements; therefore, information in this

Operator Manual is subject to change without

notice.

Model 8756 Safety

131220

Section 3 Safety

We, at Taylor Company, are concerned about the

safety of the operator at all times when they are

coming in contact with the unit and its parts. Taylor

makes every effort to design and manufacture

built-in safety features to protect both operators and

service technicians.

Installing and servicing refrigeration equipment can

be hazardous due to system pressure and electrical

components. Only trained and qualified service

personnel should install, repair, or service

refrigeration equipment. When working on

refrigeration equipment, observe precautions noted

in the literature, tags and labels attached to the unit,

and other safety precautions that may apply. Follow

all safety code requirements. Wear safety glasses

and work gloves.

IMPORTANT - Failure to adhere to the

following safety precautions may result in

severe personal injury or death. Failure to

comply with these warnings may also damage

the unit and/or its components. Such damage

may result in component replacement and

service repair expenses.

DO NOT operate the unit without reading

this entire Operator Manual first. Failure to follow all

of these operating instructions may result in damage

to the unit, poor performance, health hazards,

personal injury, or death.

This unit is to be used only by trained

personnel. It is not intended for use by children or

people with reduced physical, sensory, or mental

capabilities, or lack of experience and knowledge.

Where limited equipment operation is allowed for

public use, such as a self-serve application,

supervision or instruction concerning the use of the

appliance by a person responsible for their safety is

required. Children should be supervised to ensure

that they do not play with the appliance.

S All repairs should be performed by an

authorized Taylor service technician.

S The main power supplies to the unit must be

disconnected prior to performing installation,

repairs, or maintenance.

S DO NOT operate the unit unless it is

properly grounded.

S DO NOT operate the unit with larger fuses

than specified on the unit's data label.

S Cord Connected Units: Only Taylor

authorized service technicians or licensed

electricians may install a plug or

replacement cord on these units.

S Units that are permanently connected to

fixed wiring and for which leakage currents

may exceed 10 mA, particularly when

disconnected or not used for long periods,

or during initial installation, shall have

protective devices such as a GFI, to protect

against the leakage of current, installed by

the authorized personnel to the local codes.

S Stationary units which are not equipped with

a power cord and a plug or another device

to disconnect the appliance from the power

source must have an all-pole disconnecting

device with a contact gap of at least 3 mm

installed in the external installation.

S Supply cords used with this unit shall be

oil-resistant, sheathed flexible cable not

lighter than ordinary polychloroprene or

other equivalent synthetic

elastomer-sheathed cord (Code designation

60245 IEC 57) installed with the proper cord

anchorage to relieve conductors from strain,

including twisting, at the terminals and

protect the insulation of the conductors from

abrasion.

If the supply cord is damaged, it must be

replaced by an authorized Taylor service

technician in order to avoid a hazard.

Failure to follow these instructions may result in

electrocution. Contact your local authorized Taylor

Distributor for service.

Model 8756Safety

131220

DO NOT use a water jet to clean or rinse

the unit. Failure to follow these instructions may

result in serious electrical shock.

S DO NOT allow untrained personnel to

operate this unit.

S DO NOT operate the unit unless all service

panels and access doors are restrained with

screws.

S DO NOT remove any internal operating

parts (including, but not limited to, freezer

door, beater, or scraper blades), unless all

control switches are in the OFF position.

Failure to follow these instructions may result in

severe personal injury, especially to fingers or

hands, from hazardous moving parts.

This unit has many sharp edges that can

cause severe injuries.

S DO NOT put objects or fingers in the door

spout. This may contaminate the product

and cause severe personal injury from blade

contact.

S USE EXTREME CAUTION when removing

the beater assembly. The scraper blades

are very sharp.

This unit must be placed on a level surface.

Extreme care should be taken when moving the unit

for any reason. Two or more persons are required to

safely move this unit. Failure to comply may result in

personal injury or damage to the unit.

Access to the service area of the unit must

be restricted to persons having knowledge and

practical experience with the unit, in particular as far

as safety and hygiene are concerned.

Cleaning and sanitizing schedules are

governed by your state or local regulatory agencies

and must be followed accordingly. Please refer to

the cleaning section of this Operator Manual for the

proper procedure to clean this unit.

This unit is designed to maintain product

temperature under 41°F (5°C). Any product being

added to this unit must be below 41°F (5°C). Failure

to follow this instruction may result in health hazards

and poor freezer performance.

DO NOT run the unit without product. Failure to

follow this instruction can result in damage to the

unit.

DO NOT obstruct air intake and discharge

openings:

Air cooled units require a minimum of 3” (76 mm) of

clearance around all sides of the freezer and 12”

(305 mm) on top to allow for adequate air flow

across the condenser(s). Failure to allow adequate

clearance can reduce the refrigeration capacity of

the freezer and possibly cause permanent damage

to the compressor.

For Indoor Use Only: This unit is designed to

operate indoors, under normal ambient

temperatures of 70°-75°F (21°-24°C). The unit has

successfully performed in high ambient

temperatures of up to 104°F (40°C) at reduced

capacities.

NOISE LEVEL: Airborne noise emission does not

exceed 78 dB(A) when measured at a distance of

1.0 meter from the surface of the unit and at a

height of 1.6 meters from the floor.

Model 8756 Safety

Notes:

Model 8756Operator Parts Identification

Section 4 Operator Parts Identification

Figure 1

Model 8756 Operator Parts Identification

8756 Parts Identificatio n

ITEM DESCRIPTION PART NO.

1 PANEL A.-FRONT X22879

2 STUD-NOSE CONE 068410

3 BOLT-CARRIAGE 012347

4 PANEL A.-LOWER SIDE (R & L) X23956

5 PANEL-UPPER SIDE LEFT 028599

6 HOOD 048526

7 PANEL-UPPER REAR 022015

8 PANEL-LOWER REAR 023598

9 PANEL-UPPER SIDE RIGHT 028600

10 PAN-DRIP 17-1/4” LONG 027504

11 CASTER-SWIVEL 3/4-10 3” WHL 021279

12 GASKET-CABINET MIX DOOR 024629

13 PROBEA.-MIX(2) X35981

14 BOOT-MIX COVER 037200

15 TANK A.-MIX W/DECALS X38755

15a* TANK (ONLY) 034928

ITEM DESCRIPTION PART NO.

16 COVER-MIX TANK 024590

17 FUNNEL-MIX 036637

18 TRAY-DRIP 22-7/8 X 5-1/8 014533

19 SHIELD-SPLASH 23” LONG 022766

20 COVER-LEFT MIX STORAGE 037138

21 COVER-RIGHT MIX STORAGE 037139

22 TRIM-CORNER-LEFT/RIGHT 022013

23 TRIM A.-SIDE LEFT/RIGHT X22424

24 TRIM A.-SHELF X24813

25 TRIM-FRONT-LEFT 024824-SP

26 TRIM-FRONT-RIGHT 024825

27 TRIM-BOTTOM CABINET 024826

28 STRIP-TOP TRIM 024827

29 CASTER 3” SWIVEL (FRONT) 030307

30 SCREW-6-32 X 3/8 SLOTTED 002201

*NOT SHOWN

Model 8756Operator Parts Identification

Beater Door Assembly

Figure 2

ITEM DESCRIPTION PART NO.

1 HANDLE A.-DRAW ADJ X55096

1a HANDLE-ADJUSTABLE 028804

1b SCREW-ADJUSTMENT 055092

1c O-RING-1/4 OD X .070W 50 015872

1d NUT-5/16-24 FINISHED HEX 029639-BLK

2 ROD A.-PIVOT-SHORT X22388

3 O-RING-3/8 OD X .070W 016137

4 PLUG-PRIME 028805

5 GASKET-DOOR HT 4"-DOUBLE 048926

6 KIT A.-BEATER-FRONT SHOES X50350

6a SHOE-FRONT HELIX-REAR 050346

6b BEARING-FRONT-SHOE 050348

6c SHOE-FRONT HELIX-FRONT 050347

ITEM DESCRIPTION PART NO.

7 BEATER A.-3.4QT-1 PIN X46231

8 SHAFT-BEATER 032564

9 SEAL-DRIVE SHAFT 032560

10 BLADE-SCRAPER-PLASTIC 046235

11 CLIP-SCRAPER·BLADE-7.00·IN 046236

12 O-RING-5/16 OD X .070W 016272

13 ROD A.-PIVOT-LONG X22387

14 DOOR A.-3 SPOUT X51532-12

15 O-RING-7/8 OD X .103W 014402

16 CAP-DESIGN-1.010"ID-6 POINT 014218

17 VALVE A.-DRAW X18303

18 NUT-STUD-SHORT 034383

19 NUT-STUD-LONG 034382

Model 8756 Operator Parts Identification

Air/Mix Pump Assembly

ITEM DESCRIPTION PART NO.

1 CAP-PUMP 021276-9

2 PIN-RETAINING 021276-8

*3 PUMP A.-SOFT SERVE

COMPLETE

X22345

3a CYLINDER A.-PUMP 022345-1

3b PIN-RETAINING 021276-8

3c PISTON 021276-2

3d RING-CHECK 2” OD x 1 /2 020050

3e O-RING 2-1/8 OD x .139 W 020051

3f BODY A.-VALVE X22345-3

3g O-RING - 13/16 OD x .139 W 021278

3h ELBOW-INLET 90 DEGREE 022502-4

4 ORIFICE 023425-50

5 O-RING - 3/8 OD x .070 W 016137

6 LINE A.-FLARE 038299

7 LINE A.-PUMP PRESSUSRE X27139

8 DIAPHRAGM-PRESSURE

SWITCH

020249

9 TUBE-VINYL 5/8 ID X 1/8 WALL 020945-18

10 COUNTERWEIGHT-SUCTION

TUBE

020452

*INCLUDES ITEMS 3a-3h

Figure 3

Model 8756Operator Parts Identification

140814

Accessories

Figure 4

ITEM DESCRIPTION PART NO.

1 BRUSH-MIX PUMP BODY 023316

2 BRUSH-PRESSURE SWITCH 027647

3 BRUSH SET-LVB 050103

4 BRUSH-FEED TUBE 021101

5 BRUSH-DOUBLE ENDED 013072

6 BRUSH-REAR BEARING 013071

ITEM DESCRIPTION PART NO.

7 BRUSH-DRAW VALVE 013073

*8 SANITIZER-STERA SHEEN

GREEN

SEE NOTE

9 LUBRICANT-TAYLOR 4 OZ. 047518

10 KIT A.-TUNE UP X49463-2

11 PAIL-10 QT. 013163

*Note: A sample container of sanitizer is sent with the

unit. For reorders, order Stera Sheen part no. 055492

(100 packs) or Kay-5 part no. 041082 (125 packs).

Model 8756 Important: To the Operator

Section 5 Important: To the Operator

Figure 5

ITEM DESCRIPTION

1 POWER S WITCH (TOGGLE)

2 RESET SWITCH

3 MIX REFRIGERATION CONTROL

4 STANDBY KEY

5 WASH KEY

ITEM DESCRIPTION

6 AUTO KEY

7 PUMP KEY

8 MIX LOW INDICATOR

9 MIX OUT INDICATOR

Model 8756Important: To the Operator

Symbol Definitions

To better communicate in the International arena,

the words on many of our operator switches and

buttons have symbols to indicate their functions.

Your Taylor equipment is designed with these

International symbols.

=AUTO

=ON

=OFF

=MIXREF

= WASH

=PUMP

= STANDBY

=MIXLOW

= MIX OUT

Power Switch

When placed in the ON position, the power switch

allows SOFTECH control panel operation.

Indicator Lights -

MIX LOW and MIX OUT

When the MIX LOW light begins to flash, the mix

tank has a low supply of mix and should be refilled

as soon as possible. When the MIX OUT light

begins to flash, it indicates the mix tank has been

almost completely exhausted and has an insufficient

supply of mix to operate the freezer. At this time, the

STANDBY and AUTO modes are locked out and the

freezer shuts down. To initiate the refrigeration

system, add mix to the tank and press the AUTO

key. The freezer will automatically begin operation.

Reset Button

The reset button is located in the decorative plate

above the SOFTECH controls. The reset protects

the beater motor from an overload condition. Should

an overload occur, the reset mechanism will trip. To

properly reset the freezer, press the AUTO key to

cancel the cycle. Turn the power switch to the OFF

position. Press the reset button firmly. Turn the

power switch to the ON position. Press the WASH

key and observe the freezer's performance. The

beater motor should be turning the drive shaft in a

clockwise (from operator end) direction without

binding.

If it is turning properly, press the WASH key to

cancel the cycle. Press the AUTO key on both sides

to resume normal operation. If the freezer shuts

down again, contact a service technician.

MIX REF

When the MIX REF key is pressed, the light comes

on, indicating the mix cabinet refrigeration system is

operating. There are two touch-tone panels, one for

each freezing cylinder. The mix refrigeration system

is controlled by the MIX REF key found on the left

panel. By pressing the AUTO key on either side of

the freezer, the MIX REF function is automatically

turned on. The MIX REF function cannot be

cancelled unless the AUTO or STANDBY mode is

cancelled first.

Standby

During long “No Sale” periods it becomes necessary

to warm the product in the freezing cylinder to

approximately 35_ to 40_F(1.7_to 4.4_C) to prevent

overbeating and product breakdown.

When the STANDBY key is pressed, the light comes

on, indicating the CTR (Cylinder Temperature

Retention System) has been activated. In the

STANDBY mode, the WASH, PUMP, and AUTO

functions are automatically cancelled. The MIX REF

function is automatically locked in to maintain the

mix in the cabinet.

To resume normal operation, press the AUTO key.

When the unit cycles off, the product in the freezing

cylinder will be at serving viscosity.

Model 8756 Important: To the Operator

Wash

When the WASH key is pressed, the light comes on,

indicating beater motor operation. The STANDBY or

AUTO modes must be cancelled first to activate the

WASH mode.

Auto

When the AUTO key is pressed, the light comes on,

indicating the main refrigeration system has been

activated. In the AUTO mode, the WASH or

STANDBY functions are automatically cancelled.

The MIX REF function is automatically locked in to

maintain the mix in the cabinet and the PUMP

function is locked in to allow air/mix pump operation

as required.

Pump

When the PUMP key is pressed, the light comes on

indicating the air/mix pump will operate as required.

Note: An indicating light and an audible tone will

sound whenever a mode of operation has been

pressed. To cancel any function, press the key

again and the light and mode of operation will shut

off.

Adjustable Draw Handle

This unit features an adjustable draw handle to

provide the best portion control, giving a better,

consistent quality to your product and controlling

costs. The draw handle should be adjusted to

provide a flow rate of 5 to 7-1/2 oz. of product by

weight per 10 seconds. To increase the flow rate,

turn the screw counterclockwise. To decrease the

flow rate, turn the screw clockwise.

In addition, for purposes of sanitizing and rinsing,

the flow rate can be increased by removing the pivot

pin and placing the restrictive bar on the top.

When drawing product, always have the restrictive

bar on the bottom.

IMPORTANT! When dispensing product, pull

only one draw handle at a time.

Model 8756Operating Procedures

Section 6 Operating Procedures

The Model 8756 has two freezing cylinders. The size

of each freezing cylinder is 3.4 quarts (3.2 liters).

Mix is stored in the lower front refrigerated

compartment and is pumped up to the freezing

cylinder by an air/mix pump.

Duplicate the following procedures, where they

apply, for the second freezing cylinder.

We begin our instructions at the point where we

enter the store in the morning and find the parts laid

out to air dry from the previous night's brush

cleaning.

If you are disassembling the machine for the first

time, or need information to get to this starting point

in our instructions, turn to page 32, “Disassembly”

and start there.

Assembly

MAKE SURE THE POWER SWITCH IS IN

THE “OFF” POSITION. Failure to follow this

instruction may result in electrocution or injury to

fingers or hands from hazardous moving parts.

Step 1

Lubricate the groove and shaft portion that comes in

contact with the bearing on the beater drive shaft.

Slide the seal over the shaft and groove until it

snaps into place. DO NOT lubricate the hex end of

the drive shaft. Fill the inside portion of the seal

with1/4” more lubricant and evenly lubricate the end

of the seal that fits onto the rear shell bearing.

Figure 6

Note: For ease of cleaning, the seal may be turned

inside out. Be sure to position the seal correctly

during assembly.

Figure 7

Page is loading ...

Taylor Model 8756 User manual

Brand: Taylor

Model: Model 8756

Type: User manual

This manual is also suitable for

Frozen Dessert Maker Model 8756

Download PDF

report

Taylor Model 8756 User manual

This manual is also suitable for

Taylor Model 8756 User manual

Related papers

Other documents