Philips GC7703/20 Quick start guide

Category
Irons
Type
Quick start guide

This manual is also suitable for

Philips GC7703/20 is an advanced steam generator iron designed to make ironing easier and more efficient. With its powerful steam output, it can penetrate deep into fabrics, removing stubborn creases and leaving your clothes looking sharp and fresh. The device features an intuitive control panel with variable steam settings, allowing you to adjust the steam intensity based on the fabric type. Additionally, the GC7703/20 comes equipped with a self-clean function to maintain optimal performance and prolong the life of the iron.

Philips GC7703/20 is an advanced steam generator iron designed to make ironing easier and more efficient. With its powerful steam output, it can penetrate deep into fabrics, removing stubborn creases and leaving your clothes looking sharp and fresh. The device features an intuitive control panel with variable steam settings, allowing you to adjust the steam intensity based on the fabric type. Additionally, the GC7703/20 comes equipped with a self-clean function to maintain optimal performance and prolong the life of the iron.

FOR FIRST USE:
Turn the temperature
dial to
••
or higher
and press the trigger
continuously for up to
30 seconds for steam.
Important
information
Fastcare
DO NOT USE:
Perfumed water, vinegar,
descaling agents, ironing
aids etc.
Read and
keep me
Please
turn over for
descaling
Any questions?
OROR
R
ead and
keep me
1. Usage of right water type
2. Steam control
Steam will enhance your ironing performance.
Control the steam while ironing by using the steam trigger.
To enjoy the most out of your new steam generator, please read carefully.
For further information on usage and troubleshooting, please read
the user manual.
Recommended to use:
Demineralised water if you
live in hard water area
Tap water
Tap waterDemineralised water
OR
Don’t go back to store, Philips is here to help. Contact us directly.
www.philips.com/support
0207 949 0240 015245443
Press and hold the steam trigger
for steam during ironing.
GC7700_HULK_4239.001.0132.1_ENG_cHR.pdf 1 30-10-15 10:48
Press
2 sec
2 min
Do not leave the appliance unattended during the descaling process.
Hot water and steam will come out of the soleplate.
Do not interrupt the descaling process (approx. 2 minutes).
4239.001.0132.1
Calc-Clean
Container
Perform descaling once the
descaling light ashes and the
appliance beeps.
The steam function will be
disabled automatically if
descaling is not performed.
4. Performing descaling
Fill the water tank halfway and
switch on the appliance.
Turn the temperature dial
to ‘CALC CLEAN’.
Place the iron on the Calc-Clean
container on an even, stable surface.
Press and hold the ‘CALC CLEAN
button for 2 seconds until you
hear short beeps.
Wait approximately 2 minutes.
You will hear short beeps.
When the descaling process is
completed, the iron stops beeping.
With the
Calc-Clean container
provided, you can perform
descaling easily and
get clean steam.
3. Sound and light descaling reminder
With the new Smart Calc-Clean feature, you’ll be reminded to descale your appliance when this is needed.
Steam function
disabled
GC7700_HULK_4239.001.0132.1_ENG_cHR.pdf 2 30-10-15 10:48
  • Page 1 1
  • Page 2 2

Philips GC7703/20 Quick start guide

Category
Irons
Type
Quick start guide
This manual is also suitable for

Philips GC7703/20 is an advanced steam generator iron designed to make ironing easier and more efficient. With its powerful steam output, it can penetrate deep into fabrics, removing stubborn creases and leaving your clothes looking sharp and fresh. The device features an intuitive control panel with variable steam settings, allowing you to adjust the steam intensity based on the fabric type. Additionally, the GC7703/20 comes equipped with a self-clean function to maintain optimal performance and prolong the life of the iron.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI