Valid for Serial NO 815 XXX--XXXX0456 857 001 98.06. 10
MEK 44C
101103105107109111102021110025108024042106023061104022041100020040060001
Bruksanvisning
Brugsanvisning
Bruksanvisning
Käyttöohjeet
Instruction manual
Betriebsanweisung
Manual d’instructions
Gebruiksaanwijzing
Instrucciones de uso
Istruzioni per l’uso
Manual de instruções
Ïäçãßåò ÷ñÞóåùò
-- 2 --
Rätt till ändring av specifikationer utan avi sering förbehålles.
Ret til ændring af specifikationer uden varsel forbeholdes.
Rett til å endre spesifikasjoner uten varsel forbeholdes.
Oikeudet muutoksiin pidätetään.
Rights reserved to alter specifications without notice.
Änderungen vorbehal ten.
Sous réserve de modifications sans avis préalabl e.
Recht op wijzigingen zonder voorafgaande mededeling voorbehouden.
Reservado el derecho de cambiar las especifi caciones sin previo aviso.
Ci riserviamo il diritto di variare le specifiche senza preavviso.
Reservamo--nos o direito de alterar as especificações sem aviso prévio.
Äéáôçñåßôáé ôï äéêáßùìá ôñïðïðïßçóçò ðñïäéáãñáöþí ×ùñßò ðñïåéäïðïßçóç.
SVENSKA 3..............................................
DANSK 12................................................
NORSK 20................................................
SUOMI 28................................................
ENGLISH 36..............................................
DEUTSCH 44.............................................
FRANÇAIS 52.............................................
NEDERLANDS 60.........................................
ESPAÑOL 68..............................................
ITALIANO 76..............................................
PORTUGUÊS 84..........................................
ÅËËÇÍÉÊÁ 92.............................................
ENGLISH
TOCe
-- 3 6 --
1 DIRECTIVE 37........................................................
2SAFETY 37...........................................................
3 INTRODUCTION 38...................................................
3.1 TECHNICAL DATA 38........................................................
4 INSTALLATION 39....................................................
5 OPERATION 39.......................................................
5.1 Termination resistance 40.....................................................
6 MAINTENANCE 40....................................................
7 ORDERING SPARE PARTS 41..........................................
8 ACCESSOIRES 41....................................................
9 WEAR COMPONENTS 42..............................................
DIAGRAM 100............................................................
SPARE PARTS LIST 101...................................................
-- 3 7 --bm20d12e
1 DIRECTIVE
DECLARATION OF CONFORMITY
Esab Welding Equipment AB, S-- 695 81 Laxå, Sweden, gives its unreserved guarantee that
Wire feed unit MEK 44C from serial number 645 complies with standard EN 60974-- 1, in
accordance with the requirements of directive 73/23/ EEA and addendum 93/68/ EEA and
standard EN 50199 in accordance with the requirements of directive 89/336/ EEA and ad-
dendum 93/68/ EEA.
-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --
Paul Karlsson
Managing Director
Esab Welding Equipment AB
695 81 LAXÅ
SWEDEN Tel: + 46 584 81000 Fax: + 46 584 12336
Laxå 97--01--15
2SAFETY
WARNING
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.
ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU -
TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE
BASED ON MANUFACTURERS’ HAZARD DATA.
ELECTRIC SHOCK -- Can kill
S Install and earth the welding unit in accordance with applicable standards.
S Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S Insulate yourself from earth and the workpiece.
S Ensure your working stance is safe.
FUMES AND GASES -- Can be dangerous to health
S Keep your head out of the fumes.
S Use ventilation, extraction at the arc, or both, to keep fumes and gases from your breathing zone and
the general area.
ARC RAYS -- Can injure eyes and burn skin.
S Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE -- Excessive noise can damage hearing
S Protect your ears. Use ear defenders or other hearing protection.
S Warn bystanders of the risk.
MALFUNCTION -- Call for expert assistance in the event of malfunction.
PROTECT YOURSELF AND OTHERS!
-- 3 8 --
bm20d12e
3 INTRODUCTION
A10--MEK 44C is a four--wheel drive wire feed unit with double motors intended for
MIG/MAG welding where the wire is projected in accordance with Esab’s A10
system.
The unit has space for a wire reel with a diameter of up to 440 mm.
For a wire feed unit to be complete it must be equipped either with a turnable,
counterbalance device or a carriage. A turnable or counterbalance device allow the
wire feed unit to be mounted on a pivot on the power source. A carriage allows the
wire feed unit to be moved easily over the floor or work table.
A wire feed unit and turnable or carriage can also be fitted with a support device and
suspended over the work place.
All the settings are controlled by the PUA1 setting
box.
3.1 TECHNICAL DATA
Voltage 42 V 50--60 Hz
Power consumption 430 VA
Wire feed speed 1,5--25 m/min
Torch connection EURO
Weight 22 kg
Dimensions lxwxh 493x336x268 mm
-- 3 9 --bm20d12e
4 INSTALLATION
WARNING
This product is intended for industrial use. In a domestic environment this
product may cause radio interference. It is the user’s responsibility to take
adequate precautions.
5OPERATION
1 Connector, remote control /Intermediate wire feed unit (23--way)
2 Connector setting control
3 Adapter, welding torch
4 Connector, return cable (OKC)
5 Connector, control cable from welding power source (12--way)
6 Nipple, gas connection
7 Nipple, cooling water in Blue
8 Nipple, cooling water out Red
9 Setting control
1
4
5
6
78
7,8
9
2
3
IMPORTANT!
To prevent the reel sliding off the hub: Lock the reel in place
by turning the red knob as shown on the warning label atta-
ched next to the
hub.
-- 4 0 --
bm20d12e
5.1 Termination resistance
The termination resistance must be connected to the ends of the CAN bus to prevent
communication problems.
The controller has a built--in terminator, but the power source and wire feed unit do
not.
The terminator should be fitted as follows depending on how the units are
connected:
1. Controller con n ected to wire feed unit.
The termination resistance must be con-
nected to the rear of the power source.
(Already connected this way on delivery).
2. Controller connected to power source.
The termination resistance
must be connected to the front
of the wire feed unit.
6 MAINTENANCE
Regularly maintenance is important for r eliable and safe operations.
S Cleaning and replacement of the wire feed mechanism’s wear parts should take
place periodically to ensure trouble free wire feed.
Note that an excessive pressure setting can result in abnormal wear on the pres-
sure roller, feed roller and wire liner.
S Torch
Regularly blow the wire liner and clean the gas shroud.
-- 4 1 --bm20d12e
7 ORDERING SPARE PARTS
When ordering parts please state the m achine model, serial number and name and
spare part number as shown in the list of spare parts.
This facilitates dispatch and ensures a correct delivery.
8 ACCESSOIRES
See Spare part list.
Turntable
At the base of the turntable is a tube which can be fitted over a vertical pivot. The
turntable is delivered with an insulated pivot which can be fitted in a hole on top of
the power source, allowing the wire feed unit to be swung around as far as the gas
bottle.
Suspension device
The suspension device is intended to allow the wir e feed unit to be hung
above the work place.
There is a risk of tipping if the wire feed cabinet is fitted with a counterbalance arm.
Secure the equipment, especially if used on an uneven or sloping surface.
Limit the angle of rotation of the wire feed cabinet using the straps supplied.
When moving the equipment, do NOT pull on the torch.
WARNING!
-- 4 2 --
bm20d12e
9 WEAR COMPONENTS
Fig Qty Order no. Name Remarks
0366 942--886 Wire feed Compl.
1 1 0455 417 001 Outlet nozzles ø 0,6--1,6mm, A,B,C,D
0333 163 009 Outlet nozzles ø 2,0--2,4mm, A,B,C,D
3 1 Screw M10
4 1 0156 602 001*) Inlet nozzles ø 0,6--1,2mm, A,B,C
1 0156 602 002 Inlet nozzles ø 1,6--2,4mm, A,B,C
1 0332 318 001 Inlet nozzles ø 1,2--2,0mm, D
1 0332 318 002 Inlet nozzles ø 2,4mm, D
5 2 02157 027 08 Circlip
6 1 0156 603 001*) Intermediate nozzles ø 0,8--1,2mm, A,B,C
1 0156 603 002 Intermediate nozzles ø 1,6--2,4mm, A,B,C
1 0332 322 001 Intermediate nozzles ø 1,2--2,0mm, D
1 0332 322 002 Intermediate nozzles ø 2,4mm, D
7 1 0366 961 001 Intermediate nozzles Support
8 4 Screw M5x20
9 1 0366 941 880*) Boggie 0,6--1,2, A,B,C,(D)
1 0366 902 880 Boggie HD, A,B,C,(D)
1 0366 941 881 Boggie 1,4--2,4, A,B,C
1 0366 902 881 Boggie HD, A,B,C
1 0366 941 882 Boggie 1,2--2,0, D
1 0366 902 882 Boggie HD, D
1 0366 902 883 Boggie HD, 2,4, D
10 2 0366 966 880*) Feed rollers ø 0,,6--1,2 A,B,C,D
0366 966 881 Feed rollers ø 1,6--2,4, A,B,C,D
0366 966 882 Feed rollers ø 1,2--2,0, D
0366 966 883 Feed rollers ø2,4,D
11 4 0156 707--001 Spacer
12 2 0156 707--002 Adjustment spacer
13 2 0366 944--001 Washer
A=Fe--B=Ss--C=Al.
D= Cored wire (Knurled rollers)
HD=Heavy Duty (with ball bearings).
*) Standard.
-- 4 3 --bm20d12e
1
3
4
56
7
8
9
10
11
12
13
8
3
4
WARNING!
Rotating parts can cause injury, take great care .
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI